Woods Equipment BW180HB, BW180HDQ manual PRE-OPERATION Check List, Owners Responsibility

Page 18

STORAGE

Follow these steps when storing your cutter:

1.Clean cutter before storing. See page 23 for cleaning instructions. Store on level, solid ground.

2.Disconnect driveline and secure up off the ground.

3.Lower wings to ground.

4.Raise cutter center section and pin transport bar in raised position.

5.Attach parking jack and raise tongue weight off tractor drawbar.

6.Place wedge blocks at front and rear of wheels on center section and each wing to prevent wheel rotation.

7.Securely block all four corners of center section and each wing with jack stands.

8.Remove hydraulic hoses after tractor is turned off and all system pressure is released by operating valve levers several times.

9.Remove safety tow chain.

10.Remove retainer pin and high strength drawbar pin.

11.Keep children and bystanders away from storage area.

PRE-OPERATION CHECK LIST

(OWNER'S RESPONSIBILITY)

___ Review and follow all safety rules and safety decal instructions on page 7 through page 13.

___ Check that all safety decals are installed and in good condition. Replace if damaged.

___ Check that equipment is properly and securely attached to tractor.

___ Make sure driveline spring-activated locking pin or collar slides freely and is seated firmly in trac- tor PTO spline groove.

___ Check all lubrication points and grease as instructed in lubrication information. Make sure

 

the PTO slip joint is lubricated and that the gear-

 

box fluid levels are correct.

___

Set tractor PTO at correct rpm for your equip-

 

ment.

___

Lubricate all grease fitting locations. Make sure

 

PTO shaft slip joint is lubricated.

___

Check that all hydraulic hoses and fittings are in

 

good condition and not leaking before starting

 

tractor. Check that hoses are not twisted, bent

 

sharply, kinked, frayed, or pulled tight. Replace

 

any damaged hoses immediately.

___

Check that all hardware is properly installed and

 

secured.

___

Check cutting height and attitude adjustment.

___

Raise and lower equipment to make sure air is

 

purged from hydraulic cylinders and hoses. Raise

 

and lower equipment to make sure air is purged

 

from hydraulic cylinders and hoses.

___

Check that blades are sharp and secure and cut-

 

ting edge is positioned to lead in a counterclock-

 

wise rotation.

___

Make sure tractor ROPS or ROPS cab and seat

 

belt are in good condition. Keep seat belt

 

securely fastened during operation.

___ Check that shields and guards are properly installed and in good condition. Replace if dam- aged.

___ Before starting engine, operator must be in trac- tor seat with seat belt fastened. Place transmis- sion in neutral or park, engage brake and disengage tractor PTO.

___ Inspect area to be cut and remove stones, branches, or other hard objects that might be

 

thrown and cause injury or damage.

___

Inspect rubber or chain shielding and replace any

 

damaged rubber shield or missing links.

___

Make sure tractor 3-point lift links do not interfere

 

with hydraulic hoses or driveline throughout full

 

turning range.

18 Operation

MAN0805 (4/30/2009)

 

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Batwing Introduction To the DealerTable of Contents LEA EL InstructivoSpecifications General InformationFree Mower Safety Video SafetyTraining Package for Rotary Mowers/Cutters-English Training Package for Rotary Mowers/Cutters-English/SpanishTraining Safety RulesInstallation PreparationTransportation OperationMaintenance Storage Safety & Instructional Decals Be Careful1000 RPM Safety Operation Connecting Cutter to TractorOperation Hydraulic ConnectionCV Driveline Turning Limits Cutting Height AdjustmentInterference Check Tractor OperationCutter Operation Mowing TipsShredding Transporting Lock-UpPRE-OPERATION Check List Owners ResponsibilityOwner Service Owner ServiceBlocking Method Lubrication Gearbox LubricationDriveline Lubrication Blades Blade Installation FigureSeasonal Lubrication Blade Removal FigureSlip Clutch Adjustment Figure Blade SharpeningCleaning Shielding RepairServicing Tires Safely Troubleshooting TroubleshootingGearbox Maintenance Dealer ServiceDealer Service Seal Replacement FigureDisassembly Figure Gearbox RepairRemoval from Cutter Figure Reinstallation GearboxDisassembly AssemblySplitter Gearbox Repair Figure Removal from Cutter Reinstallation on Cutter Check GearboxCrossbar Removal Crossbar RemovalCrossbar Installation Joint DisassemblyUniversal Joint Repair Joint Assembly Assembly Assembly InstructionsDealer SET-UP Instructions Install Height Adjustment Cylinder BW180HD Install SMV Emblem BW180HDInstall Wheel and Hub BW180HD Install Tongue BW180HDInstall 3-Joint Drive 540 RPM Only BW180HD Joint Drive InstallationInstall CV Drive BW180HD- Optional Install Wing BW180HDInstall Wing Cylinder & Lock-up Bar BW180HD Install Wing Wheel and Hub All Models Left Wing Lock-Up Bar InstalledInstall Hose Kit BW180HD Install Wing Wheel Yoke Adjustment Link BW180HDInstall Wing Driveline BW180HD Winch Kit Installation OptionalInstall Chain or Belt Shielding BW180HD Chain Shielding Installation Center SectionChain Shielding Installation Right Wing Shown Belt Shielding Installation Right Wing PRE-DELIVERY Check List Dealer Check ListsDealer Check Lists Delivery Check ListMAN0805 4/30/2009 Parts BW180HD, BW180HDQ BW180HB, BW180HBQ BW126HB, BW126HBQMain Frame Assembly Front Section Part QTY Description BW180HD Main Frame Assembly Rear Section Tire & hub see BW180HB Main Frame Assembly Rear Section REF Part QTY Description Wing Assembly See Wing & Center Gearbox Assembly Center Splitter Gearbox Assembly Gear, 540 rpmCenter Deck Drive Assembly Front Drive Assembly Equal Angle Rear Drive Assembly Equal Angle Type a 540 RPM & 1000 RPM Front CV Drive Type B 540 RPM & 1000 RPM Front CV Drive Wing Drive Assembly Bolt Wheel & Tire Assembly 1027468 Rubber Shielding Wing Front & Rear Standard on BW180 Models Chain Shielding Center Section Front & Rear Single ROW Double ROWChain Shielding Wing Front & Rear Single ROWHydraulic Cylinders Crossbar Puller Optional Hydraulic Cylinder Stroke Control KITBW126HB / BW126HBQ Weight BOX Assembly Optional Winch Kit Installation Winch KIT OptionalWinch Kit Operation Appendix Bolt Torque ChartSAE Series Torque Chart Metric SeriesBolt Size Chart AbbreviationsIndex IndexWarranty Rev /23/2005

BW180HDQ, BW180HD, BW180HB specifications

Woods Equipment has long been a leader in the agricultural and landscaping industry, providing exceptional products that enhance productivity and efficiency. Among its standout offerings are the BW180HB, BW180HD, and BW180HDQ models. These versatile implements are primarily designed for use with tractors, making them invaluable for a variety of tasks.

The BW180HB model is known for its high-performance capabilities combined with a compact design. One of its main features is its heavy-duty construction, which ensures durability and longevity even under strenuous conditions. The implement is equipped with a balanced weight distribution system that allows for better stability and control during operation. Additionally, the BW180HB is designed to handle a range of tasks from grading and leveling to scraping and light dozing.

Moving up the series, the BW180HD offers a higher capacity and is built for more demanding applications. This model features a robust hydraulic system that enhances lifting capabilities, allowing operators to tackle heavier loads with ease. Its advanced blade adjustment features allow for precise angle and depth control, making it ideal for a variety of terrains. The BW180HD is particularly praised for its reliability in tough environments, thanks to its reinforced frame and high-quality materials.

The BW180HDQ model represents the pinnacle of Woods Equipment's offerings in this series. It features all the capabilities of the BW180HD but includes advanced technological enhancements for improved performance. The inclusion of an automated hydraulic control system streamlines operations, enabling operators to adjust settings on-the-fly to adapt to changing conditions. Additionally, the BW180HDQ comes with integrated safety features that protect both the operator and the equipment during use.

All three models share several common characteristics that make them preferred choices among landscaping and construction professionals. They are compatible with a wide range of tractor types, ensuring versatility for various users. The quick-connect attachment points allow for rapid changes between implements, saving time and increasing productivity. With easy maintenance designs, these models ensure that downtime is minimized, allowing operators to focus on the task at hand.

In summary, the Woods Equipment BW180HB, BW180HD, and BW180HDQ models are exceptional tools for anyone looking to enhance their operational efficiency in agriculture or landscaping. With their robust features, advanced technologies, and commitment to durability, these implements represent some of the best options available in the market today.
Top Page Image Contents