Cutter Operation, Mowing Tips, Shredding

Be sure operator is familiar with all controls and can stop tractor and cutter quickly in an emergency. The operator should give complete, undivided attention to operating tractor and cutter.

CUTTER OPERATION

When beginning operation of the cutter, make sure that all persons are in a safe location.

Power for operating the cutter is supplied by the tractor PTO. Operate PTO at 540 (1000 RPM for "Q" models).

Know how to stop the tractor and cutter quickly in an emergency.

Engage PTO at a low engine, rpm to minimize stress on the drive system and gearbox.

With PTO engaged, raise PTO speed to 540 or 1000 RPM depending on model and maintain throughout cutting operation.

Gearbox protection is provided by a slip clutch with replacement fiber disc. The slip clutch is designed to slip when excessive torsional loads occur.

Move slowly into material. Adjust tractor ground speed to provide a clean cut without lugging the tractor engine.

Use a slow ground speed for better shredding.

Proper ground speed will depend on the terrain and the material’s height, type, and density.

Normally, ground speed will range from 2 to 5 mph. Tall, dense material should be cut at a low speed; thin, medium-height material can be cut at a faster ground speed.

Always operate tractor PTO at proper RPM (540 or 1000 depending on model) to maintain blade speed and to produce a clean cut.

Under certain conditions tractor tires may roll down some grass and prevent cutting at the same height as the surrounding area. When this occurs, reduce your ground speed but maintain PTO at 540 or 1000 RPM. The lower ground speed will permit grass to rebound partially.

Mowing Tips

Look down and to the rear and make sure area is clear before operating in reverse.

Do not operate or transport on steep slopes.

Do not stop, start, or change directions sud- denly on slopes.

Use extreme care and reduce ground speed on slopes and rough terrain.

Watch for hidden hazards on the terrain during operation.

CAUTION

Stop power unit and equipment immediately upon striking an obstruction. Turn off engine, remove key, inspect, and repair any damage before resuming operation.

Maximum recommended ground speed for cutting or shredding is 6 miles per hour. Adjust tractor ground speed by using higher or lower gears to provide a clean cut without lugging tractor engine.

Tall material should be cut twice. Cut material higher the first pass. Cut at desired height at 90 degrees the second pass.

Remember, sharp blades produce cleaner cuts and use less power.

Before entering an area, analyze it to determine the best procedure. Consider the height and type of mate- rial to be cut and the terrain type (hilly, level or rough, etc.).

Shredding

The cutter may be used to shred various crops includ- ing green manure, straw, stubble, asparagus residue, corn stalks and similar crops in preparation for tilling. It may also be used to shred pruning in orchards, groves and vineyards.

Each shredding operation may require a different set- up. Start with front edge of cutter high. Adjust up or down as necessary with attitude rod. Experiment until you obtain the results you want.

When shredding attitude is set, check that the distance from the bottom rear edge of the wing to the ground matches the bottom edge of the rear center section to the ground. With the cutting height and attitude estab- lished, adjust the driveline carrier bearing in the H- frame to ensure the front driveline is parallel to the ground.

16 Operation	MAN0805 (4/30/2009)

BW180HDQ, BW180HD, BW180HB specifications

Woods Equipment has long been a leader in the agricultural and landscaping industry, providing exceptional products that enhance productivity and efficiency. Among its standout offerings are the BW180HB, BW180HD, and BW180HDQ models. These versatile implements are primarily designed for use with tractors, making them invaluable for a variety of tasks.

The BW180HB model is known for its high-performance capabilities combined with a compact design. One of its main features is its heavy-duty construction, which ensures durability and longevity even under strenuous conditions. The implement is equipped with a balanced weight distribution system that allows for better stability and control during operation. Additionally, the BW180HB is designed to handle a range of tasks from grading and leveling to scraping and light dozing.

Moving up the series, the BW180HD offers a higher capacity and is built for more demanding applications. This model features a robust hydraulic system that enhances lifting capabilities, allowing operators to tackle heavier loads with ease. Its advanced blade adjustment features allow for precise angle and depth control, making it ideal for a variety of terrains. The BW180HD is particularly praised for its reliability in tough environments, thanks to its reinforced frame and high-quality materials.

The BW180HDQ model represents the pinnacle of Woods Equipment's offerings in this series. It features all the capabilities of the BW180HD but includes advanced technological enhancements for improved performance. The inclusion of an automated hydraulic control system streamlines operations, enabling operators to adjust settings on-the-fly to adapt to changing conditions. Additionally, the BW180HDQ comes with integrated safety features that protect both the operator and the equipment during use.

All three models share several common characteristics that make them preferred choices among landscaping and construction professionals. They are compatible with a wide range of tractor types, ensuring versatility for various users. The quick-connect attachment points allow for rapid changes between implements, saving time and increasing productivity. With easy maintenance designs, these models ensure that downtime is minimized, allowing operators to focus on the task at hand.

In summary, the Woods Equipment BW180HB, BW180HD, and BW180HDQ models are exceptional tools for anyone looking to enhance their operational efficiency in agriculture or landscaping. With their robust features, advanced technologies, and commitment to durability, these implements represent some of the best options available in the market today.