Woods Equipment BW180HDQ, BW180HB manual Transportation, Operation

Page 8

SAFETY RULES

ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!

(Safety Rules continued from previous page)

Make sure driveline guard tether chains are attached to the tractor and equipment as shown in the pamphlet that accompanies the driveline. Replace if damaged or broken. Check that driveline guards rotate freely on driveline before putting equipment into service.

Before starting power unit, check all equipment driveline guards for damage. Replace any damaged guards. Make sure all guards rotate freely on all drivelines. If guards do not rotate freely on drive- lines, repair and replace bearings before putting equipment into service.

Power unit must be equipped with ROPS or ROPS cab and seat belt. Keep seat belt securely fastened. Falling off power unit can result in death from being run over or crushed. Keep foldable ROPS system in “locked up” position at all times.

Remove accumulated debris from this equip- ment, power unit, and engine to avoid fire hazard.

Make sure all safety decals are installed. Replace if damaged. (See Safety Decals section for location.)

Make sure shields and guards are properly installed and in good condition. Replace if damaged.

Always attach safety chain to tractor drawbar when transporting unit.

Always comply with all state and local lighting and marking requirements.

Never allow riders on power unit or attachment.

Do not operate PTO during transport.

Do not operate or transport on steep slopes.

Do not operate or transport equipment while under the influence of alcohol or drugs.

The maximum transport speed for towed and semi-mounted machines is 20 mph (32 km/h). Regardless of the maximum speed capability of the towing tractor, do not exceed the implement’s max- imum transport speed. Doing so could result in:

Loss of control of the implement and tractor

Reduced or no ability to stop during braking

Implement tire failure

Damage to the implement or its components.

Use additional caution and reduce speed when under adverse surface conditions, turning, or on inclines.

Never tow this implement with a motor vehicle.

Do not put this equipment into service unless all side skids are properly installed and in good condi- tion. Replace if damaged.

A minimum 20% of tractor and equipment weight must be on the tractor front wheels when attachments are in transport position. Without this weight, tractor could tip over, causing personal injury or death. The weight may be attained with a loader, front wheel weights, ballast in tires or front tractor weights. Weigh the tractor and equipment. Do not estimate.

Inspect and clear area of stones, branches, or other hard objects that might be thrown, causing injury or damage.

TRANSPORTATION

Power unit must be equipped with ROPS or ROPS cab and seat belt. Keep seat belt securely fastened. Falling off power unit can result in death from being run over or crushed. Keep foldable ROPS system in “locked up” position at all times.

Always raise unit and install transport locks before transporting. Leak down or failure of mechanical or hydraulic system can cause equip- ment to drop.

OPERATION

Do not allow bystanders in the area when oper- ating, attaching, removing, assembling, or servic- ing equipment.

Never walk, stand, or place yourself or others under a raised wing or in the path of a lowering wing. Hydraulic system leak-down, hydraulic sys- tem failures, mechanical failures, or movement of control levers can cause wings to drop unexpect- edly and cause severe injury or death.

Full chain or rubber shielding must be installed when operating in populated areas or other areas where thrown objects could injure people or dam- age property.

If this machine is not equipped with full chain or rubber shielding, operation must be stopped when anyone comes within 300 feet (92 m).

This shielding is designed to reduce the risk of thrown objects. The mower deck and protec- tive devices cannot prevent all objects from escaping the blade enclosure in every mowing condition. It is possible for objects to ricochet and escape, traveling as much as 300 feet (92 m).

Never direct discharge toward people, animals, or property.

8Safety

BW180_SR (Rev. 12/10/2007)

Image 8
Contents Batwing Introduction To the DealerTable of Contents LEA EL InstructivoSpecifications General InformationFree Mower Safety Video SafetyTraining Package for Rotary Mowers/Cutters-English Training Package for Rotary Mowers/Cutters-English/SpanishSafety Rules InstallationTraining PreparationTransportation OperationMaintenance Storage Safety & Instructional Decals Be Careful1000 RPM Safety Connecting Cutter to Tractor OperationOperation Hydraulic ConnectionCutting Height Adjustment Interference CheckCV Driveline Turning Limits Tractor OperationShredding Cutter OperationMowing Tips Transporting Lock-UpPRE-OPERATION Check List Owners ResponsibilityBlocking Method Owner ServiceOwner Service Driveline Lubrication LubricationGearbox Lubrication Blade Installation Figure Seasonal LubricationBlades Blade Removal FigureSlip Clutch Adjustment Figure Blade SharpeningServicing Tires Safely CleaningShielding Repair Troubleshooting TroubleshootingDealer Service Dealer ServiceGearbox Maintenance Seal Replacement FigureRemoval from Cutter Figure Disassembly FigureGearbox Repair Reinstallation GearboxSplitter Gearbox Repair Figure Removal from Cutter DisassemblyAssembly Reinstallation on Cutter Check GearboxCrossbar Removal Crossbar RemovalUniversal Joint Repair Crossbar InstallationJoint Disassembly Joint Assembly Dealer SET-UP Instructions AssemblyAssembly Instructions Install Height Adjustment Cylinder BW180HD Install SMV Emblem BW180HDInstall Wheel and Hub BW180HD Install Tongue BW180HDInstall 3-Joint Drive 540 RPM Only BW180HD Joint Drive InstallationInstall Wing Cylinder & Lock-up Bar BW180HD Install CV Drive BW180HD- OptionalInstall Wing BW180HD Install Wing Wheel and Hub All Models Left Wing Lock-Up Bar InstalledInstall Wing Wheel Yoke Adjustment Link BW180HD Install Wing Driveline BW180HDInstall Hose Kit BW180HD Winch Kit Installation OptionalInstall Chain or Belt Shielding BW180HD Chain Shielding Installation Center SectionChain Shielding Installation Right Wing Shown Belt Shielding Installation Right Wing Dealer Check Lists Dealer Check ListsPRE-DELIVERY Check List Delivery Check ListMAN0805 4/30/2009 Parts BW180HD, BW180HDQ BW180HB, BW180HBQ BW126HB, BW126HBQMain Frame Assembly Front Section Part QTY Description BW180HD Main Frame Assembly Rear Section Tire & hub see BW180HB Main Frame Assembly Rear Section REF Part QTY Description Wing Assembly See Wing & Center Gearbox Assembly Center Splitter Gearbox Assembly Gear, 540 rpmCenter Deck Drive Assembly Front Drive Assembly Equal Angle Rear Drive Assembly Equal Angle Type a 540 RPM & 1000 RPM Front CV Drive Type B 540 RPM & 1000 RPM Front CV Drive Wing Drive Assembly Bolt Wheel & Tire Assembly 1027468 Rubber Shielding Wing Front & Rear Standard on BW180 Models Chain Shielding Center Section Front & Rear Single ROW Double ROWChain Shielding Wing Front & Rear Single ROWHydraulic Cylinders Crossbar Puller Optional Hydraulic Cylinder Stroke Control KITBW126HB / BW126HBQ Weight BOX Assembly Optional Winch Kit Operation Winch Kit InstallationWinch KIT Optional Bolt Torque Chart SAE Series Torque ChartAppendix Metric SeriesBolt Size Chart AbbreviationsIndex IndexWarranty Rev /23/2005

BW180HDQ, BW180HD, BW180HB specifications

Woods Equipment has long been a leader in the agricultural and landscaping industry, providing exceptional products that enhance productivity and efficiency. Among its standout offerings are the BW180HB, BW180HD, and BW180HDQ models. These versatile implements are primarily designed for use with tractors, making them invaluable for a variety of tasks.

The BW180HB model is known for its high-performance capabilities combined with a compact design. One of its main features is its heavy-duty construction, which ensures durability and longevity even under strenuous conditions. The implement is equipped with a balanced weight distribution system that allows for better stability and control during operation. Additionally, the BW180HB is designed to handle a range of tasks from grading and leveling to scraping and light dozing.

Moving up the series, the BW180HD offers a higher capacity and is built for more demanding applications. This model features a robust hydraulic system that enhances lifting capabilities, allowing operators to tackle heavier loads with ease. Its advanced blade adjustment features allow for precise angle and depth control, making it ideal for a variety of terrains. The BW180HD is particularly praised for its reliability in tough environments, thanks to its reinforced frame and high-quality materials.

The BW180HDQ model represents the pinnacle of Woods Equipment's offerings in this series. It features all the capabilities of the BW180HD but includes advanced technological enhancements for improved performance. The inclusion of an automated hydraulic control system streamlines operations, enabling operators to adjust settings on-the-fly to adapt to changing conditions. Additionally, the BW180HDQ comes with integrated safety features that protect both the operator and the equipment during use.

All three models share several common characteristics that make them preferred choices among landscaping and construction professionals. They are compatible with a wide range of tractor types, ensuring versatility for various users. The quick-connect attachment points allow for rapid changes between implements, saving time and increasing productivity. With easy maintenance designs, these models ensure that downtime is minimized, allowing operators to focus on the task at hand.

In summary, the Woods Equipment BW180HB, BW180HD, and BW180HDQ models are exceptional tools for anyone looking to enhance their operational efficiency in agriculture or landscaping. With their robust features, advanced technologies, and commitment to durability, these implements represent some of the best options available in the market today.