Yazoo/Kees ZCBI48181 manual Tools Required For Assembly, To Remove the Mower from Crate

Page 12

ASSEMBLY

Your new mower has been assembled at the factory with the exception of those parts left un- assembled for shipping purposes. To ensure safe and proper operation of your mower, all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to insure proper tightness.

TOOLS REQUIRED

FOR ASSEMBLY

1.9/16" wrench or 9/16" socket w/ drive ratchet

2.Tire pressure gauge

3.Nail bar or claw hammer

4.Wire snips

When right or left hand is mentioned in this manual, it means when you are in the operating position (seated).

TO REMOVE THE MOWER FROM CRATE

UNPACK CRATE

Using the nail bar or hammer, remove the top of the crate first. Then remove the sides of the crate and place these out of the way. Be careful of any exposed nails or staples.

Remove the plastic bag that covers the mower.

Using the wire snips, cut any plastic ties that are holding the mower to the crate.

Remove the seat off of the front of the mower and place in a safe location.

BEFORE REMOVING THE

MOWER FROM THE SKID

ATTACH SEAT (See Fig. 1)

The seat position should be adjusted forward or backward so that the operator can comfortably reach the deck lift pedal and safely operate the mower. See "Service and Adjustment" Section of this manual.

Remove protective wrap from the seat.

Remove the three prong knobs and washers from the seat and place in the storage area in the right side console.

Raise the seat pan up so that the bottom can be easily accessed.

Securing one of the three prong knobs and washers, insert it thru the seat pan slot and into the corresponding threaded hole in the seat bottom.

Repeat for the other three holes.

Tighten the three prong knobs in the approximate position desired for the seat.

Connect the wiring harness to the seat switch.

Adjustments may be required to position the seat in the desired position. Refer to the "Service and Adjustment" section of this manual.

SEAT PAN

 

 

KNOBS

WIRE

 

HARNESS

 

FIGURE 1

CZ-1

 

ATTACH CONTROL LEVERS (See Fig. 2)

Using the 9/16" wrench or socket and ratchet, remove the bottom hex bolt and spring washer from the control arm.

Rotate the control lever up until the bolt and spring washer can be placed thru the slot in the bottom of the control lever and threaded back into the control arm.

Center the hex bolt in the slot on the control lever. Using the wrench or ratchet, tighten both the top and bottom hex bolts.

Repeat on opposite side of the mower.

12

Image 12
Contents Operators Manual Models ZCBI48181Good Service Contents Symbols and Decals Safety Instructions Safety InstructionsGeneral Use Personal protective equipment Driving on Slopes Do as followsChildren 8011-563 Transport Important InformationSpecifications Customer ResponsibilitiesAssembly Tools Required For AssemblyTo Remove the Mower from Crate Before Removing Mower from the SkidOn position Checklist Check the Tire PressureOperation ControlsIZT Integraded Zeroturn TransaxleBYPASS Linkages HOW to USE Your Mower Deck BladesEngine To Adjust the Deck Cutting Height See Fig To Adjust ANTI-SCALP Rollers See FigureTo Operate Mower To Operate on HillsTo Transport See Fig Before Starting the Engine To Start Engine See FigCheck Engine OIL Level ADD GasolineMowing Tips Maintenance Schedule General RecommendationsBefore Each USE Lubrication Chart Operator Presence SystemBlade Care TiresBattery To Sharpen Blade See FigClean AIR Screen Clean AIR INTAKE/COOLING AreasBelts EngineCleaning AIR FilterEngine OIL Filter Spark PlugsService and Adjustment Before Performing ANY Service or AdjustmentsMower To Level DeckFRONT-TO-BACKADJUSTMENTSee Fig To Replace Deck BeltTo Replace IZT Integraded Zeroturn Transaxle Belt See Fig To Adjust the Seat See Fig To Adjust Control Levers See FigTo Start AN Engine with a Weak Battery To Remove Wheels for RepairReplacing Battery See Fig To Attach Jumper CablesTo Adjust Park Brake Tracking AdjustmentBattery StorageFuel System Engine OILOther CylindersTroubleshooting Points Problem Cause CorrectionProblemcausecorrection Attachment Poor cut unevenWiring Schematic Page