Yazoo/Kees ZCBI48181 manual Service and Adjustment, Mower, To Level Deck

Page 27

SERVICE AND ADJUSTMENT

WARNING

BEFORE PERFORMING ANY SERVICE OR ADJUSTMENTS:

Set park brake to engaged position.

Place PTO switch in the disengaged position (pressed down).

Turn ignition key "OFF" and remove the key.

Make sure the blades and all moving parts have completely stopped.

Disconnect spark plug wire from spark plug and place the wire where it cannot come in contact with the plug.

and rear lift linkages (be sure to tighten equal amounts).

To lower one side of the deck, reverse previous step.

Recheck measurements after adjustment.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

A

 

 

 

 

 

 

 

 

 

 

 

 

A

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

CZ-16

FIGURE 13

MOWER

TO LEVEL DECK

Adjust the deck while the mower is on a level surface. Make sure the tires are inflated to the correct pressure (see “SPECIFICATIONS” section in this manual). If tires are under or over inflated, you can not properly adjust your deck.

NOTE: It may be easier to adjust the front lift linkages by removing the floor pan before any adjustments are made

SIDE-TO-SIDE ADJUSTMENT (See Figs. 13 and 14)

Raise the deck into the highest cutting

 

position (4 1/2")

Measure height from the bottom edge of

 

the deck to the ground at both front

 

corners. Distance “A” at both corners

HEX NUT

FRONT LIFT

LINKAGE

FIGURE 14

CZ-17

 

REAR LIFT

LINKAGE

should be the same.

• If adjustment is necessary, make

adjustment to one side the deck only

• To raise one side of the deck, using a 9/16"

wrench, tighten the hex nuts on both the

front

HEX NUT

FIGURE 14A

CZ-18

27

Image 27
Contents ZCBI48181 Operators Manual ModelsGood Service Contents Symbols and Decals Safety Instructions Safety InstructionsGeneral Use Personal protective equipment Do as follows Driving on SlopesChildren 8011-563 Important Information TransportCustomer Responsibilities SpecificationsBefore Removing Mower from the Skid AssemblyTools Required For Assembly To Remove the Mower from CrateOn position Check the Tire Pressure ChecklistOperation ControlsIZT Integraded Zeroturn TransaxleBYPASS Linkages HOW to USE Your Mower Deck BladesEngine To Adjust the Deck Cutting Height See Fig To Operate on Hills To Adjust ANTI-SCALPRollers See Figure To Operate MowerTo Transport See Fig ADD Gasoline Before Starting the EngineTo Start Engine See Fig Check Engine OIL LevelMowing Tips Maintenance Schedule General RecommendationsBefore Each USE Tires Lubrication ChartOperator Presence System Blade CareTo Sharpen Blade See Fig BatteryEngine Clean AIR ScreenClean AIR INTAKE/COOLING Areas BeltsSpark Plugs CleaningAIR Filter Engine OIL FilterTo Level Deck Service and AdjustmentBefore Performing ANY Service or Adjustments MowerTo Replace Deck Belt FRONT-TO-BACKADJUSTMENTSee FigTo Replace IZT Integraded Zeroturn Transaxle Belt See Fig To Remove Wheels for Repair To Adjust the Seat See FigTo Adjust Control Levers See Fig To Start AN Engine with a Weak BatteryTo Attach Jumper Cables Replacing Battery See FigTracking Adjustment To Adjust Park BrakeEngine OIL BatteryStorage Fuel SystemCylinders OtherProblem Cause Correction Troubleshooting PointsAttachment Poor cut uneven ProblemcausecorrectionWiring Schematic Page