Yazoo/Kees ZCBI48181 manual To Replace Deck Belt, FRONT-TO-BACKADJUSTMENTSee Fig

Page 28

SERVICE AND ADJUSTMENT

FRONT-TO-BACKADJUSTMENT(See Fig. 15).

IMPORTANT: DECK MUST BE LEVEL SIDE-

TO-SIDE. IF THE FOLLOWING FRONT-TO-

BACK ADJUSTMENT IS NECESSARY, BE

SURE TO ADJUST BOTH FRONT OR BOTH

REAR LINKAGES EQUALLY SO THE DECK

WILL STAY LEVEL.

BB

To obtain the best cutting performance, the deck should be adjusted so the front tip of the blades are approximately 1/8" to 1/4" lower than the rear tip. If the front tip is higher, this will create a poor quality of cut.

FIGURE 15

CZ-19

WARNING

Blades are sharp. Protect your hands with gloves and/or wrap blades with a heavy cloth when handling.

Check adjustment on the right side of the mower. Position any blade so that the tip is pointing straight forward. Measure distance “B” at the front and rear tip of the blade.

•Before making any necessary adjustments, check to make sure that the deck is level side-to-side.

•With the deck in the highest cutting position, (4 1/2") measure the front tip of the blade to see if the deck is higher or lower than 4 1/2".

•To lower the front tip of the blade, using a 9/16" wrench, loosen the hex nuts that are on the front lift linkages (be sure to loosen equal amounts).

•When distance “B” is 1/8" to 1/4" lower at the front than rear the adjustment is done.

•Reverse above step to raise the deck.

TO REPLACE DECK BELT

DECK BELT REMOVAL (See Fig. 16 and 17)

•Park on a level surface. Apply park brake.

•Lower the deck into the lowest cutting position

•Disengage the tension relief lever from the lock bracket.

WARNING

Lever is spring loaded. Have a tight grip on the lever and release slowly.

•Remove screws from both the left and right belt shields, and remove shields.

•Remove any dirt or grass that may have accumulated around the cutter housings and entire deck surface.

•Carefully roll the belt over the top of the cutter housing pulleys.

•Remove the belt from around the electric clutch on the engine shaft.

•The belt can now be removed.

28

Page 27 Page 29
Image 28
Page 27 Page 29
Contents Operators Manual Models ZCBI48181Good Service Contents Symbols and Decals Safety Instructions Safety InstructionsGeneral Use Personal protective equipment Driving on Slopes Do as followsChildren 8011-563 Transport Important InformationSpecifications Customer ResponsibilitiesAssembly Tools Required For AssemblyTo Remove the Mower from Crate Before Removing Mower from the SkidOn position Checklist Check the Tire PressureControls OperationIZT Integraded Zeroturn TransaxleBYPASS Linkages Deck Blades HOW to USE Your MowerEngine To Adjust the Deck Cutting Height See Fig To Adjust ANTI-SCALP Rollers See FigureTo Operate Mower To Operate on HillsTo Transport See Fig Before Starting the Engine To Start Engine See FigCheck Engine OIL Level ADD GasolineMowing Tips General Recommendations Maintenance ScheduleBefore Each USE Lubrication Chart Operator Presence SystemBlade Care TiresBattery To Sharpen Blade See FigClean AIR Screen Clean AIR INTAKE/COOLING AreasBelts EngineCleaning AIR FilterEngine OIL Filter Spark PlugsService and Adjustment Before Performing ANY Service or AdjustmentsMower To Level DeckFRONT-TO-BACKADJUSTMENTSee Fig To Replace Deck BeltTo Replace IZT Integraded Zeroturn Transaxle Belt See Fig To Adjust the Seat See Fig To Adjust Control Levers See FigTo Start AN Engine with a Weak Battery To Remove Wheels for RepairReplacing Battery See Fig To Attach Jumper CablesTo Adjust Park Brake Tracking AdjustmentBattery StorageFuel System Engine OILOther CylindersTroubleshooting Points Problem Cause CorrectionProblemcausecorrection Attachment Poor cut unevenWiring Schematic Page
Top Page Image Contents