Yazoo/Kees ZCBI48181 manual To Replace IZT Integraded Zeroturn Transaxle Belt See Fig

Page 29
FIGURE 16

SERVICE AND ADJUSTMENT

DECK BELT INSTALLATION (See Figs. 16 and 17)

NOTE: For ease in installing the deck belt, refer to the routing decal on the front edge of the deck.

•Wrap the deck belt around the electric clutch that is located on the engine shaft.

•Push the rest of the belt through the IZT(Integraded Zeroturn Transaxle) support and up onto the deck.

•Starting on the right hand side of the deck, wrap the belt around the large right side idler, right cutter housing pulley, small center idler, center pulley, left side pulley and then around the large left side idler.

•The belt will be loose at this point.

•Tightly secure the belt tension rod and reengage it in the lock bracket.

TO REPLACE IZT (Integraded Zeroturn Transaxle) BELT (See Fig. 17)

Park the mower on a level surface. Engage the park brake.

IZT BELT REMOVAL

NOTE: Be careful not to damage the fan blades on the IZT’s as this can affect cooling or damage the IZT’s

•Remove the deck belt (see “TO REPLACE DECK BELT” in this section of the manual).

•Create slack in the belt by removing the spring on the pump idler arm.

•The belt should now be able to be removed from the engine pulley and IZT pulleys.

BELT INSTALLATION

•Wrap the IZT belt around the IZT pulleys

•Route the belt around the inside of the idler pulley.

•Now you can wrap the belt around the engine pulley.

•Reattach the spring on the pump idler arm.

•Reinstall the deck belt onto the electric clutch belt (see “TO REPLACE DECK BELT” in this section of the manual).

TENSION RELIEF LEVER

PUMP IDLER ARM SPRING

PUMP IDLER

ELECTRIC CLUTCH

IZT BELT

DECK BELT

IZT SUPPORT

CZ-20

FIGURE 16A

CZ-21

FIGURE 17

29

Page 28 Page 30
Image 29
Page 28 Page 30
Contents ZCBI48181 Operators Manual ModelsGood Service Contents Symbols and Decals General Use Safety InstructionsSafety Instructions Personal protective equipment Do as follows Driving on SlopesChildren 8011-563 Important Information TransportCustomer Responsibilities SpecificationsTools Required For Assembly AssemblyTo Remove the Mower from Crate Before Removing Mower from the SkidOn position Check the Tire Pressure ChecklistIZT Integraded Zeroturn TransaxleBYPASS Linkages OperationControls Engine HOW to USE Your MowerDeck Blades To Adjust the Deck Cutting Height See Fig Rollers See Figure To Adjust ANTI-SCALPTo Operate Mower To Operate on HillsTo Transport See Fig To Start Engine See Fig Before Starting the EngineCheck Engine OIL Level ADD GasolineMowing Tips Before Each USE Maintenance ScheduleGeneral Recommendations Operator Presence System Lubrication ChartBlade Care TiresTo Sharpen Blade See Fig BatteryClean AIR INTAKE/COOLING Areas Clean AIR ScreenBelts EngineAIR Filter CleaningEngine OIL Filter Spark PlugsBefore Performing ANY Service or Adjustments Service and AdjustmentMower To Level DeckTo Replace Deck Belt FRONT-TO-BACKADJUSTMENTSee FigTo Replace IZT Integraded Zeroturn Transaxle Belt See Fig To Adjust Control Levers See Fig To Adjust the Seat See FigTo Start AN Engine with a Weak Battery To Remove Wheels for RepairTo Attach Jumper Cables Replacing Battery See FigTracking Adjustment To Adjust Park BrakeStorage BatteryFuel System Engine OILCylinders OtherProblem Cause Correction Troubleshooting PointsAttachment Poor cut uneven ProblemcausecorrectionWiring Schematic Page
Top Page Image Contents