Yazoo/Kees ZCBI48181 manual On position

Page 13

ASSEMBLY

Adjustments may be required to get uniform positioning of the control lever. Refer to the "Service and Adjustment" section of this manual.

NOTE: You may now roll or drive the mower off of the skid. Follow the appropriate instruction below to remove the mower from the skid.

CONTROL

LEVER

CONTROL

ARM

HEX

BOLTS

NEUTRAL

SLOT

TO DRIVE THE MOWER OFF OF THE SKID (See Operation section for location and function of controls)

WARNING

Before starting, read, understand and follow all instructions in the Operation section of this manual. Be sure the mower is in a well-ventilated area. Be sure the area in front of the mower is clear of other people and objects.

• Be sure all of the above assembly

steps have been completed.

• Check engine oil level and fill fuel

tank with gasoline.

• Place the IZT(Integraded Zeroturn

Transaxle) bypass linkages into the

drive position (See “TRANSPORT” in

the Operation section of this manual).

• Sit on the seat in the operating

position, set the park brake lever to

FIGURE 2

CZ-2

the on position.

• Rotate the control levers outward

into the neutral slot.

TO ROLL THE MOWER OFF OF THE SKID (See Operation section for location and function of controls

•Move to the rear of the mower, and place the IZT (Integraded Zeroturn Transaxle) bypass linkages into the bypass position to disengage the IZT’s (See “TO TRANSPORT” in the Operation section of this manual).

•Sitting on the mower, press the deck lift pedal in to the highest cutting position.

•Release park brake lever.

•Roll the mower forward or backward off of the skid.

• Press forward on the deck lift pedal

to raise the deck into the highest

cutting position.

• Place the throttle control into the

choke position.

• Start the engine. After the engine

has started, move the throttle control

to the idle position.

• Release the park brake.

• Move the control levers into the

operate position.

• Slowly move the control levers

forward and slowly drive the mower

off of the skid.

• Return the control levers back to the

neutral position.

• Apply the park brake.

• Turn the ignition key to the “OFF”

position.

13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents ZCBI48181 Operators Manual ModelsGood Service Contents Symbols and Decals Safety Instructions Safety InstructionsGeneral Use Personal protective equipment Do as follows Driving on SlopesChildren 8011-563 Important Information TransportCustomer Responsibilities SpecificationsTools Required For Assembly AssemblyTo Remove the Mower from Crate Before Removing Mower from the SkidOn position Check the Tire Pressure ChecklistControls OperationIZT Integraded Zeroturn TransaxleBYPASS Linkages Deck Blades HOW to USE Your MowerEngine To Adjust the Deck Cutting Height See Fig Rollers See Figure To Adjust ANTI-SCALPTo Operate Mower To Operate on HillsTo Transport See Fig To Start Engine See Fig Before Starting the EngineCheck Engine OIL Level ADD GasolineMowing Tips General Recommendations Maintenance ScheduleBefore Each USE Operator Presence System Lubrication ChartBlade Care TiresTo Sharpen Blade See Fig BatteryClean AIR INTAKE/COOLING Areas Clean AIR ScreenBelts EngineAIR Filter CleaningEngine OIL Filter Spark PlugsBefore Performing ANY Service or Adjustments Service and AdjustmentMower To Level DeckTo Replace Deck Belt FRONT-TO-BACKADJUSTMENTSee FigTo Replace IZT Integraded Zeroturn Transaxle Belt See Fig To Adjust Control Levers See Fig To Adjust the Seat See FigTo Start AN Engine with a Weak Battery To Remove Wheels for RepairTo Attach Jumper Cables Replacing Battery See FigTracking Adjustment To Adjust Park BrakeStorage BatteryFuel System Engine OILCylinders OtherProblem Cause Correction Troubleshooting PointsAttachment Poor cut uneven ProblemcausecorrectionWiring Schematic Page
Top Page Image Contents