MTD MT700 manual Spark Arrestor Maintenance, Carburetor Adjustment, Check Fuel Mixture

Page 14

MAINTENANCE AND REPAIR INSTRUCTIONS

SPARK ARRESTOR MAINTENANCE

NOTE: The exhaust can only flow in one direction: AWAY

from the engine. Pay close attention when disassembling the muffler so you can put it back together correctly. Failure to do so will damage the unit and may cause serious personal injury.

1.Remove air filter/muffler cover. Refer to Removing the Air Filter/Muffler Cover.

2.Locate the muffler, but do not remove it. Find the two

(2) screws on the bottom of the muffler (Fig. 26). These two screws hold the Spark Arrestor Hood Assembly and the spark arrestor screen to the bottom of the muffler. Remove the two (2) screws using either a torx #20 or flat blade screwdriver.

3.Using a small flat blade screwdriver, carefully pry up the spark arrestor screen from the recessed hole, taking care to notice that the “raised” part of the spark arrestor screen is inside the recessed hole. Remove the spark arrestor screen from the muffler.

4.Clean the spark arrestor screen with a wire brush. Replace it if it is damaged, or if you are unable to clean it thoroughly.

5.Reinstall the spark arrestor screen by putting the “raised” portion of the screen inside the recessed hole of the muffler. Make sure that the spark arrestor screen fits flat against the muffler.

6.Place the spark arrestor plate on top of the spark arrestor with the “raised” side up and the opening facing towards the engine (Fig. 26).

7.Place the spark arrestor hood on top of the spark arrestor plate with the “raised” side up and the opening facing AWAY from the engine (Fig. 26). Verify that the exhaust will be directed AWAY from the engine.

8.Replace the two screws you removed in Step 2 and tighten them securely.

9.Reinstall the air filter/muffler cover.

WARNING: If the exhaust deflector assembly is

not tightened securely, it could fall off causing damage to the unit and possible serious personal injury.

Muffler

Spark Arrestor

Screen

Spark Arrestor

Plate

Opening

Engine

Recessed Hole

Spark Arrestor Hood

Spark Arrestor

Assembly Includes:

Spark Arrestor Plate

Hood

Spark Arrestor Hood

 

Screws

and Screws

 

 

 

 

 

 

 

Fig. 26

 

 

 

 

 

 

CARBURETOR ADJUSTMENT

The idle speed of the engine is adjustable through the air filter/muffler cover (Fig. 27).

NOTE: Careless adjustments can seriously damage your unit. An authorized service dealer should make carburetor adjustments.

Check Fuel Mixture

Old and/or improperly mixed fuel is usually the reason for improper unit performance. Drain and refill the tank with fresh, properly-mixed fuel prior to making any adjustments. Refer to Oil and Fuel Information.

14

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Operator’s Manual Introduction Before Operating Safety Warnings for GAS TrimmersRules for Safe Operation Other Safety Warnings While OperatingSafety and International Symbols Symbol MeaningKnow Your Unit ApplicationsInstall the Cutting Attachment Shield Assembly InstructionsInstall and Adjust the D-HANDLE OIL and Fuel Information Using Blended FuelsUsing Fuel Additives OIL and Fuel Mixing InstructionsSTARTING/STOPPING Instructions Starting InstructionsHolding the Trimmer Adjusting Trimming Line LengthOperating Instructions Tips for Best Trimming ResultsLine Installation Maintenance and Repair InstructionsMaintenance Schedule Frequency Maintenance Required Refer toSingle Line Installation SplitLine InstallationCleaning the Air Filter Installing a Prewound ReelAIR Filter Maintenance Reinstalling the Air Filter/Muffler CoverCheck Fuel Mixture Spark Arrestor MaintenanceCarburetor Adjustment Replacing the Spark Plug Clean Air FilterAdjust Idle Speed Screw Long Term Storage CleaningStorage TransportingTroubleshooting Specifications EngineManufacturer’s Warranty Coverage Your Warranty Rights and ObligationsOwners Warranty Responsibilities MTD LLC Manuel de Lutilisateur Table DES Matières Tous NOS RemerciementsNformations D’ENTRETIEN PARE-ÉTINCELLESAvertissement lessenceest Avertissement le nonMise EN Garde le non Consignes DE SécuritéPendant Lutilisation DE Lappareil Autres Avertissements DE SécuritéSymboles DE Sécurité ET Internationaux FAMILIARISEZ-VOUS Avec L’APPAREIL ApplicationsAvertissement nutilisez Installation ET Réglage DE LA Poignée EN DInstallation DU Protecteur Daccessoire DE Coupe Instructions DE MontageAvertissement Ajoutezdu Mise EN Garde PourassurerAvertissement Enlevezle Informations SUR Lhuile ET LE CarburantInstructions DE Démarrage Avertissement évitez toutInstructions DE Démarrage ET Arrêt Instructions DarrêtMode Demploi Mise EN Garde nenlevezEntretien ET Réparations Installation DU FILAvertissement pouréviter Rembobiner le moulinet intérieur existantInstallation du fil simple Installation du SplitLineMCNettoyage DU Filtre Á Aire Avertissement pour éviterEntretien DU Filtre À AIR Vérification du mélange de carburant Entretien DU PARE-ÉTINCELLESRéglage DU Carburateur Nettoyage du filtre à airAvertissement une fois Remplacement DE LA BougieAvertissement ilquese peut Mise EN Garde évitez deEntreposage DE Longue Durée NettoyageEntreposage TransportDépannage Caractéristiques MoteurGarantie du fabricant Vos droits et obligations en vertu de cette garantieResponsabilités du propriétaire en vertu de cette garantie Garantie Limitée DU Fabricant Pour Manuel del Dueño/Operador Introduccion LEA Todas LAS Instrucciones Advertencia Laes muygasolinaNormas Para UNA Operacion Segura Advertencias DE Seguridad Para LOS Recortadores a GasolinaDurante LA Operacion Otras Advertencias DE SeguridadSimbolos DE Seguridad E Internacionales Conozca SU Unidad AplicacionesInstalación Y Ajuste DE LA Manija EN D Advertencia No opereInstrucciones DE Ensamble Instalacion DEL Protector Accesorio DE CorteAdvertencia Saque la Precaucion Para que elAdvertencia Lagasolina es Advertencia Cargue elInstrucciones DE Arranque Advertencia Evite losInstrucciones DE Arranque Y Apagado Instrucciones DE ApagadoComo Sostener EL Recortador Advertencia UsesiempreInstrucciones DE Operacion Ajuste DE LA Longitud DE LA Linea DE CorteInstrucciones DE Mantenimiento Y Reparacion Advertencia Para evitarAdvertencia No use Programa DE MantenimientoInstalación de la línea individual Instalación de la línea SplitLineRemoción de la cubierta del silenciador/filtro de aire Instalación DE UN Carrete PrebobinadoMantenimiento DEL Filtro DE Aire Limpieza del Filtro de AireAjuste DEL Carburador Advertencia SiconjuntoelMantenimiento DEL Parachispas Controle la mezcla del combustibleAjuste del tornillo de marcha lenta Advertencia ElaccesorioPrecaucion No limpie Cambio DE LA Bujia DE EncendidoAlmacenamiento Prolongado LimpiezaAlmacenamiento TransporteResolucion DE Problemas EJE Impulsor Y Accesorio DE Corte EspecificacionesMotor Sus Derechos y Obligaciones de la Garantía Notas E21 Parts List Engine Parts MT700 Cycle GAS TrimmerBoom & Trimmer Parts MT700 Cycle GAS Trimmer Garantía Limitada DEL Fabricante Para

MT700 specifications

The MTD MT700 is a highly sophisticated tractor designed to meet the demands of modern agriculture. Its advanced engineering showcases a blend of power, efficiency, and flexibility, making it a valuable asset for farmers and agricultural professionals.

One of the standout features of the MTD MT700 is its powerful engine. Equipped with a robust powertrain, the MT700 delivers impressive horsepower, providing operators with the capability to tackle heavy workloads and challenging terrains. This reliability ensures that farmers can depend on the tractor for at various tasks such as plowing, tilling, and hauling.

The MT700 incorporates cutting-edge technology to enhance performance and operational efficiency. It features a highly responsive hydrostatic transmission, allowing for smooth acceleration and deceleration. This transmission system enables operators to maintain precise control over speed and torque, essential for various farming applications. Moreover, the tractor's intuitive control system streamlines operation, reducing the learning curve for new users and increasing productivity.

A notable characteristic of the MT700 is its innovative design aimed at comfort and convenience. The spacious cab is ergonomically designed with user-friendly controls and ample visibility, allowing operators to work long hours without fatigue. The climate-controlled environment ensures comfort regardless of external conditions, which is crucial for prolonged operations in the field.

Additionally, the MT700 is designed for versatility. Its mounting system accommodates a wide range of implements, from seeders to mowers, making it suitable for various agricultural tasks. This adaptability further enhances its utility on diverse farms.

Furthermore, the MTD MT700 is built with durability in mind. Constructed with high-quality materials and components, it withstands the rigors of demanding agricultural operations. The tractor's maintenance-friendly design facilitates easy servicing, ensuring that it remains in optimal working condition year-round.

In summary, the MTD MT700 tractor represents the pinnacle of agricultural engineering, combining powerful performance, advanced technologies, and user-centric design. Farmers and agricultural professionals can rely on this tractor to enhance productivity and efficiency, making it an essential tool in modern farming operations. With its impressive features and capabilities, the MTD MT700 is poised to transform the way agriculture is conducted, setting new standards in the industry.
Top Page Image Contents