MTD MT700 manual Assembly Instructions, Install and Adjust the D-HANDLE

Page 7

ASSEMBLY INSTRUCTIONS

INSTALL AND ADJUST THE D-HANDLE

1.Push the D-handle down onto the shaft housing so that the handle slants towards the shaft grip (Fig. 1). The squared bolt hole in the handle is to the right.

2.Insert the shoulder bolt into the squared hole in the handle and push through. On the left side of the handle, place the washer on the bolt, then screw the wing nut onto the bolt. Do not tighten until you make the handle adjustment.

3.Rotate the D-handle to place the grip above the top of the shaft housing. Place it a minimum of 6 inches (15.24 cm) from the end of the shaft grip.

Shaft Grip

Shaft Housing

D-Handle

 

Tighten

Minimum 6 inches

Wing Nut

(15.24 cm)

Bolt

Washer

 

Fig. 1

4.While holding the unit in the operating position (Fig. 2), position the D-handle to the location that provides you the best grip.

5.Tighten the wing nut until the D-handle is secure.

Fig. 2

INSTALL THE CUTTING ATTACHMENT SHIELD

Use the following instructions if the cutting attachment shield on your unit is not installed.

WARNING: Never operate the trimmer without the

cutting attachment shield in place to prevent serious personal injury.

1.Place the cutting attachment shield onto the shaft housing. Be sure the guard mounting bracket slides into the slot on the edge of the cutting shield. Rotate the shield into place, counterclockwise. The holes in the guard mounting bracket and cutting attachment shield will line up (Fig. 3).

Shaft Housing

Guard

Mounting

Bracket

Cutting Attachment

Shield

Fig. 3

2.From inside the cutting attachment shield, push the square bolt through the hole until the threaded end protrudes through the guard mounting bracket (Fig. 4).

Guard

Mounting Washer

Bracket

Wing Nut

Square Bolt

Fig. 4

3.Put the washer on the bolt, then screw the wing nut onto the bolt and tighten. Figure 5 shows the installation process from underneath the unit.

Square Bolt

Hole

Cutting

AttachmentWasher

Shield

Wing Nut

Cutting Attachment and Shield: Underside View

Fig. 5

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Operator’s Manual Introduction Rules for Safe Operation Safety Warnings for GAS TrimmersBefore Operating While Operating Other Safety WarningsSymbol Meaning Safety and International SymbolsApplications Know Your UnitInstall and Adjust the D-HANDLE Assembly InstructionsInstall the Cutting Attachment Shield OIL and Fuel Mixing Instructions Using Blended FuelsUsing Fuel Additives OIL and Fuel InformationStarting Instructions STARTING/STOPPING InstructionsTips for Best Trimming Results Adjusting Trimming Line LengthOperating Instructions Holding the TrimmerFrequency Maintenance Required Refer to Maintenance and Repair InstructionsMaintenance Schedule Line InstallationSplitLine Installation Single Line InstallationReinstalling the Air Filter/Muffler Cover Installing a Prewound ReelAIR Filter Maintenance Cleaning the Air FilterCarburetor Adjustment Spark Arrestor MaintenanceCheck Fuel Mixture Adjust Idle Speed Screw Clean Air FilterReplacing the Spark Plug Transporting CleaningStorage Long Term StorageTroubleshooting Engine SpecificationsOwners Warranty Responsibilities Your Warranty Rights and ObligationsManufacturer’s Warranty Coverage MTD LLC Manuel de Lutilisateur PARE-ÉTINCELLES Tous NOS RemerciementsNformations D’ENTRETIEN Table DES MatièresConsignes DE Sécurité Avertissement le nonMise EN Garde le non Avertissement lessenceestAutres Avertissements DE Sécurité Pendant Lutilisation DE LappareilSymboles DE Sécurité ET Internationaux Applications FAMILIARISEZ-VOUS Avec L’APPAREILInstructions DE Montage Installation ET Réglage DE LA Poignée EN DInstallation DU Protecteur Daccessoire DE Coupe Avertissement nutilisezInformations SUR Lhuile ET LE Carburant Mise EN Garde PourassurerAvertissement Enlevezle Avertissement AjoutezduInstructions Darrêt Avertissement évitez toutInstructions DE Démarrage ET Arrêt Instructions DE DémarrageMise EN Garde nenlevez Mode DemploiRembobiner le moulinet intérieur existant Installation DU FILAvertissement pouréviter Entretien ET RéparationsInstallation du SplitLineMC Installation du fil simpleEntretien DU Filtre À AIR Avertissement pour éviterNettoyage DU Filtre Á Aire Nettoyage du filtre à air Entretien DU PARE-ÉTINCELLESRéglage DU Carburateur Vérification du mélange de carburantMise EN Garde évitez de Remplacement DE LA BougieAvertissement ilquese peut Avertissement une foisTransport NettoyageEntreposage Entreposage DE Longue DuréeDépannage Moteur CaractéristiquesResponsabilités du propriétaire en vertu de cette garantie Vos droits et obligations en vertu de cette garantieGarantie du fabricant Garantie Limitée DU Fabricant Pour Manuel del Dueño/Operador Introduccion Advertencias DE Seguridad Para LOS Recortadores a Gasolina Advertencia Laes muygasolinaNormas Para UNA Operacion Segura LEA Todas LAS InstruccionesOtras Advertencias DE Seguridad Durante LA OperacionSimbolos DE Seguridad E Internacionales Aplicaciones Conozca SU UnidadInstalacion DEL Protector Accesorio DE Corte Advertencia No opereInstrucciones DE Ensamble Instalación Y Ajuste DE LA Manija EN DAdvertencia Cargue el Precaucion Para que elAdvertencia Lagasolina es Advertencia Saque laInstrucciones DE Apagado Advertencia Evite losInstrucciones DE Arranque Y Apagado Instrucciones DE ArranqueAjuste DE LA Longitud DE LA Linea DE Corte Advertencia UsesiempreInstrucciones DE Operacion Como Sostener EL RecortadorPrograma DE Mantenimiento Advertencia Para evitarAdvertencia No use Instrucciones DE Mantenimiento Y ReparacionInstalación de la línea SplitLine Instalación de la línea individualLimpieza del Filtro de Aire Instalación DE UN Carrete PrebobinadoMantenimiento DEL Filtro DE Aire Remoción de la cubierta del silenciador/filtro de aireControle la mezcla del combustible Advertencia SiconjuntoelMantenimiento DEL Parachispas Ajuste DEL CarburadorCambio DE LA Bujia DE Encendido Advertencia ElaccesorioPrecaucion No limpie Ajuste del tornillo de marcha lentaTransporte LimpiezaAlmacenamiento Almacenamiento ProlongadoResolucion DE Problemas Motor EspecificacionesEJE Impulsor Y Accesorio DE Corte Sus Derechos y Obligaciones de la Garantía Notas E21 Engine Parts MT700 Cycle GAS Trimmer Parts ListBoom & Trimmer Parts MT700 Cycle GAS Trimmer Garantía Limitada DEL Fabricante Para

MT700 specifications

The MTD MT700 is a highly sophisticated tractor designed to meet the demands of modern agriculture. Its advanced engineering showcases a blend of power, efficiency, and flexibility, making it a valuable asset for farmers and agricultural professionals.

One of the standout features of the MTD MT700 is its powerful engine. Equipped with a robust powertrain, the MT700 delivers impressive horsepower, providing operators with the capability to tackle heavy workloads and challenging terrains. This reliability ensures that farmers can depend on the tractor for at various tasks such as plowing, tilling, and hauling.

The MT700 incorporates cutting-edge technology to enhance performance and operational efficiency. It features a highly responsive hydrostatic transmission, allowing for smooth acceleration and deceleration. This transmission system enables operators to maintain precise control over speed and torque, essential for various farming applications. Moreover, the tractor's intuitive control system streamlines operation, reducing the learning curve for new users and increasing productivity.

A notable characteristic of the MT700 is its innovative design aimed at comfort and convenience. The spacious cab is ergonomically designed with user-friendly controls and ample visibility, allowing operators to work long hours without fatigue. The climate-controlled environment ensures comfort regardless of external conditions, which is crucial for prolonged operations in the field.

Additionally, the MT700 is designed for versatility. Its mounting system accommodates a wide range of implements, from seeders to mowers, making it suitable for various agricultural tasks. This adaptability further enhances its utility on diverse farms.

Furthermore, the MTD MT700 is built with durability in mind. Constructed with high-quality materials and components, it withstands the rigors of demanding agricultural operations. The tractor's maintenance-friendly design facilitates easy servicing, ensuring that it remains in optimal working condition year-round.

In summary, the MTD MT700 tractor represents the pinnacle of agricultural engineering, combining powerful performance, advanced technologies, and user-centric design. Farmers and agricultural professionals can rely on this tractor to enhance productivity and efficiency, making it an essential tool in modern farming operations. With its impressive features and capabilities, the MTD MT700 is poised to transform the way agriculture is conducted, setting new standards in the industry.
Top Page Image Contents