MTD 5DM Gear sections damaged, Speed while extending Excessive pump inlet vacuum, Retracting

Page 15

Problem

 

Cause

 

Remedy

Slow cylinder shaft

1.

Gear sections damaged.

1.

See authorized service dealer.

speed while extending

2.

Excessive pump inlet vacuum.

2.

Make certain pump inlet hoses are

and retracting.

 

 

 

clear and unblocked-use short,

 

 

 

 

large diameter inlet hoses.

 

3.

Slow engine speed.

3.

See authorized service dealer.

 

4.

See authorized service dealer.

 

4.

Damaged relief valve.

 

5.

Check oil level.

 

5.

Incorrect oil level.

 

6.

Drain oil, clean reservoir, and refill.

 

6.

Contaminated oil.

 

7.

See authorized service dealer.

 

7.

Directional valve leaking internally.

 

8.

See authorized service dealer.

 

8.

Internally damaged cylinder.

 

9.

Move log splitter to level ground.

 

9.

Unit not on level ground.

 

 

 

Leaking Cylinder

1.

Broken seals.

1.

See authorized service dealer.

 

2.

Scored cylinder.

2.

See authorized service dealer.

 

 

 

 

 

Engine runs but wood

1.

Small gear section damaged.

1.

See authorized service dealer.

will not split or wood

2.

Pump check valve leaking.

2.

See authorized service dealer.

splits too slowly

3.

Excessive pump inlet vacuum.

3.

Make certain pump inlet hoses are

 

 

 

 

clear and unblocked.

 

4.

Incorrect oil level.

4.

Check oil level.

 

 

 

 

5.

Contaminated oil.

5.

Drain oil, clean reservoir, and refill.

 

 

 

 

6.

Directional valve leaking internally.

6.

See authorized service dealer.

 

 

 

 

7.

Overloaded cylinder.

7.

Do not attempt to split wood

 

 

against the grain.

 

 

 

 

 

8.

Internally damaged cylinder.

8.

See authorized service dealer.

 

 

 

 

9.

Worn belt.

9.

Replace belt.

 

 

 

 

10. Unit not on level ground.

10. Move log splitter to level ground.

 

 

 

Engine stalls during

1.

Low horsepower/weak engine.

1.

See authorized service dealer.

splitting

2.

Overloaded cylinder.

2.

Do not attempt to split wood

 

 

 

 

against the grain or see authorized

 

 

 

 

service dealer.

 

 

 

 

 

Engine will not turn or

1.

Engine/pump misalignment.

1.

Correct alignment as necessary.

stalls under low load

2.

Frozen or seized pump.

2.

See authorized service dealer.

conditions

3.

Low horsepower/weak engine.

3.

See authorized service dealer.

 

4.

Hydraulic lines blocked.

4.

Flush and clean hydraulic system.

 

5.

Blocked directional valve.

5.

Flush and clean hydraulic system.

 

 

 

 

 

Leaking pump shaft

1.

Broken drive shaft.

1.

See authorized service dealer.

seal

2.

Engine/pump misalignment.

2.

Correct alignment as necessary.

 

3.

Gear sections damaged.

3.

See authorized service dealer.

 

4.

Poorly positioned shaft seal.

4.

See authorized service dealer.

 

5.

Plugged oil breather.

5.

Make certain reservoir is properly

 

 

 

 

vented.

 

 

 

 

 

6

Hydraulic

Trouble

Shooting

For repairs beyond the minor adjust- ments listed here, contact an authorized service dealer.

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Log Splitter Model Series 5DM 769-0348325/07 Table of Contents Finding and Recording Model NumberCustomer Support Safety Labels Found On Your Log Splitter Safety LabelsDo not adjust the pressure settings of the pump or valve Your ResponsibilityDo not check for leaks with your hand Use only your hand to operate the controls Spark ArrestorAverage Useful Life Allow machine to cool at least 5 minutes before storingHandling equipment Setting Up Your Log SplitterIgnition When handlingIs hot or running Extinguish cigaKnow Your Log Splitter Operating Your Log SplitterStarting Log Splitter Engine SwitchStarter Rope ChokeBefore Each Use Using the Log SplitterOperating Forward Your Log Splitter Stopping Log SplitterAlways Use clean fluid and check fluid level regularlyUse when fluid is below 20 F or above 150 F Operating TipsMaintaining Your Log Splitter Replace spark plug Clean the log splitter thoroughlyStoring Your Log Splitter Engine Pulley Pump Idler Pulley NutCause Remedy Problem Cause RemedyGear sections damaged Engine stalls during Low horsepower/weak engineService dealer Conditions Low horsepower/weak engineDo not overfill fuel tank. Fill tank to approximately When transporting equipment, transport with fuel tankCm below lowest portion of neck to allow for fuel expansion Do not choke carburetor to stop engineInternational Symbols and Meanings Safety Label LocationPre-Operation Check Operating Your EngineKnow Your Engine This engine isFuel Recommendations Turn engine switch to onStarting The Engine Stopping The EngineTasks Oil ServiceMaintaining Your Oil ChangeAir Cleaner Service Spark Plug ServiceMaintaining Your Engine Clean Engine StorageRemoving From Storage TWO Year Limited Warranty Model Series 5DM For parts and/or accessories refer to customer support on Parts List Pièces DétachéesMANUFACTURER’S Warranty Coverage EPA-1 Air à Filtre BougiesPropriétaire DU Responsabilités 24 CA-1-EPAANS Deux DE Limitée Garantie Moteur du Entretien Service en RemiseBougie la de Entretien Air à filtre du EntretienJamais N’utilisez Avertissement ’huile de Vidange ’essence panneFacilement plus coule Carburant Le concernant RecommandationsMoteur du Arrêt Moteur du marche en MiseAmbiante Température ’huile concernant RecommandationsMoteur le avec vous-Familiarisez ’huile niveau du VérificationSignification leur et internationaux Symboles Existent d’entorsesBijoux Moteur le Cylindre Hydraulique système du problème de cas EnBois LentementDépannage Hydraulique système du problème de case EnFeudense la de Entretien Saison hors RemisageMoteur Poulie Garantie la annulant Situations Courroie la de ChangementFente de couteau et Poutre Hydraulique Huile’utilisation Conseils Fendeuse la de ment -FonctionneFendeuse la de Utilisation Emploi chaque AvantFendeuse la de Arrêt Démarreur du Corde Fendeuse la de marche en MiseMoteur du Commutateur Départ de VoletMouvement Fendeuse la de CommandesPoignée Hydraulique soupape la de ManetteFendeuse la de Montage Bloquer le etÉpingle-goupille Fendeuse la de Préparation Chaud Responsabilité VotreSeulement Responsabilité VotreFendeuse la sur sécurité de Étiquettes Sécurité de ÉtiquettesVente-après Service Modèle de numéro le trouver PourMatières des Table 25/07 03483-769 Important 5DM série la de Fendeuse

5DM specifications

MTD 5DM is an innovative work scheduling and management solution designed to streamline operations for businesses across various sectors. At its core, MTD 5DM aims to enhance productivity by offering advanced tools and features that cater to the complex demands of modern workplaces.

One of the standout features of MTD 5DM is its intuitive user interface. The platform is designed with user experience in mind, making it accessible for employees at all levels. This ease of navigation means that organizations can implement the system with minimal training, enabling rapid adoption and reducing downtime.

Another significant characteristic of MTD 5DM is its advanced scheduling capabilities. The system utilizes smart algorithms to optimize work schedules, taking into account various factors such as employee availability, skill sets, and project deadlines. This adaptability ensures that businesses can effectively allocate resources, minimizing any potential delays and enhancing operational efficiency.

MTD 5DM also integrates state-of-the-art cloud technology, allowing for real-time data access and updates. This enables teams to collaborate seamlessly, regardless of their physical locations. With cloud synchronization, all team members can stay informed and aligned on project statuses, fostering improved communication and teamwork.

In terms of analytics, MTD 5DM boasts robust reporting features that provide organizations with valuable insights into their operations. Advanced data analytics tools allow managers to monitor performance metrics, resource utilization, and employee productivity. This data-driven approach empowers businesses to make informed decisions, identify areas for improvement, and create strategies for future growth.

Security is a top priority for MTD 5DM. The platform employs cutting-edge encryption technologies to protect sensitive data, ensuring compliance with industry regulations and safeguarding against potential breaches. This commitment to security builds trust among users, enhancing the overall user experience.

Compatibility is another key feature of MTD 5DM. The platform can be seamlessly integrated with existing systems, enhancing its functionality and allowing businesses to leverage their current technology investments effectively. By providing interconnectivity with various software solutions, MTD 5DM becomes a versatile tool that adapts to the unique needs of each organization.

In summary, MTD 5DM is a comprehensive work management solution characterized by its user-friendly interface, advanced scheduling capabilities, cloud technology, robust analytics, stringent security measures, and compatibility with existing systems. By leveraging these features, businesses can optimize their operations, enhance productivity, and stay competitive in an ever-evolving marketplace.
Top Page Image Contents