MTD 5DM warranty Spark Arrestor, Average Useful Life, Use only your hand to operate the controls

Page 5

f.Never overfill the fuel tank. Fill tank to no more than 1/2 inch below bottom of filler neck to provide space for fuel expansion.

g.Replace gasoline cap and tighten securely.

h.If gasoline is spilled, wipe it off the engine and equipment. move machine to another area. Wait 5 minutes before starting the engine.

i.Never store the machine or fuel container inside where there is an open flame, spark or pilot light as on a water heater, space heater, furnace, clothes dryer or other gas appliances.

j.Allow machine to cool at least 5 minutes before storing.

OPERATION

1.Before staring this machine, review the “Safety Instructions”. Failure to follow these rules may result in serious injury to the operator or bystanders.

2.Never leave this machine unattended with the engine running.

3.Do not operate machine while under the influence of alcohol, drugs, or medication.

4.Never allow anyone to operate this machine without proper instruction.

5.Always operate this machine with all safety equipment in place and working. Make sure all controls are properly adjusted for safe operation.

6.Do not change the engine governor settings or overspeed the engine. The governor controls the maximum safe operating speed of the engine.

7.When loading a log, always place your hands on the sides of the log, not on the ends, and never use your foot to help stabilize a log. Failure to do so, may result in crushed or amputated fingers, toes, hand, or foot.

8.Use only your hand to operate the controls.

9.Never attempt to split more than one log at a time unless the ram has fully extended and a second log is needed to complete the separation of the first log.

10.For logs which are not cut square, the least square end and the longest portion of the log should be placed toward the beam and wedge, and the square end placed toward the end plate.

11.Always keep fingers away from any cracks that open in the log while splitting. They can quickly close and pinch or amputate your fingers.

12.Keep your work area clean. Immediately remove split wood around the machine so that you do not stumble over it.

13.Never move this machine while the engine is running.

14.This machine should not be towed on any street, highway, or public road behind a vehicle.

MAINTENANCE AND STORAGE

1.Stop the engine, disconnect the spark plug and ground it against the engine before cleaning, or inspecting the machine.

2.Stop the engine and relieve hydraulic system pressure before repairing or adjusting fittings, hoses, tubing, or other system components.

3.To prevent fires, clean debris and chaff from the engine and muffler areas. If the engine is equipped with a spark arrester muffler, clean and inspect it regularly according to manufacturers instructions. Replace if damaged.

4.Periodically check that all nuts and bolts, hose clamps, and hydraulic fittings are tight to be sure equipment is in safe working condition.

5.Check all safety guards and shields to be sure they are in the proper position. Never operate with safety guards, shields, or other protective features removed.

6.The pressure relief valve is preset at the factory. Do not adjust the valve.

7.Never attempt to move this machine over hilly or uneven terrain without a tow vehicle or adequate help.

8.For your safety, replace all damaged or worn parts immediately with original equipment manufacturer’s (O.E.M.) parts only. “Use of parts which do not meet the original equipment specifications may lead to improper performance and compromise safety!”

9.Do not alter this machine in any manner, alterations such as attaching a rope or extension to the control lever, or adding to the width or height of the wedge may result in personal injury.

Spark Arrestor

Warning: This machine is equipped with an internal combustion engine and should not be used on or near any unimproved forest-covered, brushcov- ered or grass-covered land unless the engine’s exhaust system is equipped with a spark arrester meeting appli- cable local or provincial laws (if any).

If a spark arrester is used, it should be maintained in effective working order by the operator.

A spark arrester for the muffler is available through your nearest engine authorized service dealer.

Average Useful Life

According to the Consumer Products Safety Commis- sion (CPSC) and the U.S. Environmental Protection Agency (EPA), this product has an Average Useful Life of seven (7) years, or 60 hours of operation. At the end of the Average Useful Life, buy a new machine or have the machine inspected annually by an authorized service dealer to ensure that all mechanical and safety systems are working properly and not worn excessively. Failure to do so can result in accidents, injuries or death.

2

Safe

Operation

Practices

WARNING

This symbol points out important safety instructions which, if not followed, could endanger the personal safety and/or property of yourself and others. Read and follow all instructions in this manual before at- tempting to operate this machine. Failure to comply with these instructions may result in personal injury. When you see this symbol,

HEED ITS WARNING!

Your Responsibility Restrict the use

of this power machine to persons who read, understand

and follow the warnings and instructions

in this manual

and on the machine.

Page 4 Page 6
Image 5
Page 4 Page 6
Contents 25/07 Log Splitter Model Series 5DM769-03483 Customer Support Table of ContentsFinding and Recording Model Number Safety Labels Found On Your Log Splitter Safety LabelsDo not check for leaks with your hand Do not adjust the pressure settings of the pump or valveYour Responsibility Average Useful Life Spark ArrestorAllow machine to cool at least 5 minutes before storing Use only your hand to operate the controlsHandling equipment Setting Up Your Log SplitterIs hot or running When handlingExtinguish ciga IgnitionKnow Your Log Splitter Operating Your Log SplitterStarter Rope Engine SwitchChoke Starting Log SplitterOperating Forward Your Log Splitter Using the Log SplitterStopping Log Splitter Before Each UseUse when fluid is below 20 F or above 150 F Use clean fluid and check fluid level regularlyOperating Tips AlwaysMaintaining Your Log Splitter Storing Your Log Splitter Clean the log splitter thoroughlyEngine Pulley Pump Idler Pulley Nut Replace spark plugCause Remedy Problem Cause RemedyService dealer Engine stalls during Low horsepower/weak engineConditions Low horsepower/weak engine Gear sections damagedCm below lowest portion of neck to allow for fuel expansion When transporting equipment, transport with fuel tankDo not choke carburetor to stop engine Do not overfill fuel tank. Fill tank to approximatelyInternational Symbols and Meanings Safety Label LocationKnow Your Engine Operating Your EngineThis engine is Pre-Operation CheckStarting The Engine Turn engine switch to onStopping The Engine Fuel RecommendationsMaintaining Your Oil ServiceOil Change TasksMaintaining Your Engine Air Cleaner ServiceSpark Plug Service Removing From Storage Clean EngineStorage TWO Year Limited Warranty Model Series 5DM For parts and/or accessories refer to customer support on Parts List Pièces DétachéesMANUFACTURER’S Warranty Coverage EPA-1 Air à Filtre BougiesPropriétaire DU Responsabilités 24 CA-1-EPAANS Deux DE Limitée Garantie Moteur du Entretien Service en RemiseJamais N’utilisez Avertissement Bougie la de EntretienAir à filtre du Entretien Facilement plus coule ’huile de Vidange’essence panne Moteur du Arrêt Le concernant RecommandationsMoteur du marche en Mise CarburantMoteur le avec vous-Familiarisez ’huile concernant Recommandations’huile niveau du Vérification Ambiante TempératureBijoux Signification leur et internationaux SymbolesExistent d’entorses Moteur le Bois Hydraulique système du problème de cas EnLentement CylindreDépannage Hydraulique système du problème de case EnMoteur Poulie Feudense la de EntretienSaison hors Remisage Fente de couteau et Poutre Courroie la de ChangementHydraulique Huile Garantie la annulant Situations’utilisation Conseils Fendeuse la de ment -FonctionneFendeuse la de Arrêt Fendeuse la de UtilisationEmploi chaque Avant Moteur du Commutateur Fendeuse la de marche en MiseDépart de Volet Démarreur du CordePoignée Fendeuse la de CommandesHydraulique soupape la de Manette MouvementÉpingle-goupille Fendeuse la de MontageBloquer le et Fendeuse la de Préparation Chaud Responsabilité VotreSeulement Responsabilité VotreFendeuse la sur sécurité de Étiquettes Sécurité de ÉtiquettesMatières des Table Vente-après ServiceModèle de numéro le trouver Pour 25/07 03483-769 Important 5DM série la de Fendeuse

5DM specifications

MTD 5DM is an innovative work scheduling and management solution designed to streamline operations for businesses across various sectors. At its core, MTD 5DM aims to enhance productivity by offering advanced tools and features that cater to the complex demands of modern workplaces.

One of the standout features of MTD 5DM is its intuitive user interface. The platform is designed with user experience in mind, making it accessible for employees at all levels. This ease of navigation means that organizations can implement the system with minimal training, enabling rapid adoption and reducing downtime.

Another significant characteristic of MTD 5DM is its advanced scheduling capabilities. The system utilizes smart algorithms to optimize work schedules, taking into account various factors such as employee availability, skill sets, and project deadlines. This adaptability ensures that businesses can effectively allocate resources, minimizing any potential delays and enhancing operational efficiency.

MTD 5DM also integrates state-of-the-art cloud technology, allowing for real-time data access and updates. This enables teams to collaborate seamlessly, regardless of their physical locations. With cloud synchronization, all team members can stay informed and aligned on project statuses, fostering improved communication and teamwork.

In terms of analytics, MTD 5DM boasts robust reporting features that provide organizations with valuable insights into their operations. Advanced data analytics tools allow managers to monitor performance metrics, resource utilization, and employee productivity. This data-driven approach empowers businesses to make informed decisions, identify areas for improvement, and create strategies for future growth.

Security is a top priority for MTD 5DM. The platform employs cutting-edge encryption technologies to protect sensitive data, ensuring compliance with industry regulations and safeguarding against potential breaches. This commitment to security builds trust among users, enhancing the overall user experience.

Compatibility is another key feature of MTD 5DM. The platform can be seamlessly integrated with existing systems, enhancing its functionality and allowing businesses to leverage their current technology investments effectively. By providing interconnectivity with various software solutions, MTD 5DM becomes a versatile tool that adapts to the unique needs of each organization.

In summary, MTD 5DM is a comprehensive work management solution characterized by its user-friendly interface, advanced scheduling capabilities, cloud technology, robust analytics, stringent security measures, and compatibility with existing systems. By leveraging these features, businesses can optimize their operations, enhance productivity, and stay competitive in an ever-evolving marketplace.
Top Page Image Contents