MTD 5DM warranty Starter Rope, Engine Switch, Choke, Starting Log Splitter

Page 9

Starter Rope

The starter rope is located on the engine. See Figure 4-1. Pull the recoil starter rope to start the unit.

Engine Switch

The engine switch is located on the engine. Turn it on when starting the engine and use it to turn off the engine.

Choke

The choke is located on the engine and when activated, closes the choke plate on the carburetor and aids in starting the engine.

Starting Log Splitter

WARNING: Always keep hands and feet clear of equipment moving parts. Do not use a pressurized starting fluid. Vapors are flammable.

NOTE: Make sure hydraulic pump is primed as instructed in the “Setting Up Your Log Splitter” section.

1.Remove locking pin from cylinder storage position. See Figure 4-2.

2.Use handle to slide cylinder rearward into the operat- ing “Lock” position, engaging the safety switch, and reinsert locking pin. See Figure 4-3.

3.Place the log splitter on level, dry, and solid ground.

4.Pull out the choke knob located on the engine. See Figure 4-4 inset.

NOTE: Use of the choke may not be necessary if the engine is warm or the air temperature is high.

5.Turn engine switch to on. See Figure 4-4 inset.

6.Pull the starter grip lightly until resistance is felt, then pull rapidly to overcome compression, prevent kickback and start engine. See Figure 4-4. If engine does not start after ten seconds of repeated pulls, wait a few minutes and repeat.

IMPORTANT: Do not allow the starter grip to snap back against the rope guide. Return it gently to prevent damage to the starter.

7.When engine warms up, push in the choke knob.

8.Use the hydraulic valve control to extend and retract cylinder 4-6 cycles to remove trapped air in the system.

WARNING: When starting a warm engine, the muffler and surrounding areas are hot and can cause a burn. Do not touch.

Figure 4-2

Safety Switch

Figure 4-3

Figure 4-4

4

Operating

Your Log

Splitter

WARNING

Always keep hands and feet clear of equip- ment moving parts. Do not use a pressurized starting fluid. Vapors are flammable.

When starting a warm engine, the muffler and surrounding areas are hot and can cause a burn. Do not touch.



Page 8 Page 10
Image 9
Page 8 Page 10
Contents Log Splitter Model Series 5DM 769-0348325/07 Table of Contents Finding and Recording Model NumberCustomer Support Safety Labels Found On Your Log Splitter Safety LabelsDo not adjust the pressure settings of the pump or valve Your ResponsibilityDo not check for leaks with your hand Average Useful Life Spark ArrestorAllow machine to cool at least 5 minutes before storing Use only your hand to operate the controlsHandling equipment Setting Up Your Log SplitterIs hot or running When handlingExtinguish ciga IgnitionKnow Your Log Splitter Operating Your Log SplitterStarter Rope Engine SwitchChoke Starting Log SplitterOperating Forward Your Log Splitter Using the Log SplitterStopping Log Splitter Before Each UseUse when fluid is below 20 F or above 150 F Use clean fluid and check fluid level regularlyOperating Tips AlwaysMaintaining Your Log Splitter Storing Your Log Splitter Clean the log splitter thoroughlyEngine Pulley Pump Idler Pulley Nut Replace spark plugCause Remedy Problem Cause RemedyService dealer Engine stalls during Low horsepower/weak engineConditions Low horsepower/weak engine Gear sections damagedCm below lowest portion of neck to allow for fuel expansion When transporting equipment, transport with fuel tankDo not choke carburetor to stop engine Do not overfill fuel tank. Fill tank to approximatelyInternational Symbols and Meanings Safety Label LocationKnow Your Engine Operating Your EngineThis engine is Pre-Operation CheckStarting The Engine Turn engine switch to onStopping The Engine Fuel RecommendationsMaintaining Your Oil ServiceOil Change TasksAir Cleaner Service Spark Plug ServiceMaintaining Your Engine Clean Engine StorageRemoving From Storage TWO Year Limited Warranty Model Series 5DM For parts and/or accessories refer to customer support on Parts List Pièces DétachéesMANUFACTURER’S Warranty Coverage EPA-1 Air à Filtre BougiesPropriétaire DU Responsabilités 24 CA-1-EPAANS Deux DE Limitée Garantie Moteur du Entretien Service en RemiseBougie la de Entretien Air à filtre du EntretienJamais N’utilisez Avertissement ’huile de Vidange ’essence panneFacilement plus coule Moteur du Arrêt Le concernant RecommandationsMoteur du marche en Mise CarburantMoteur le avec vous-Familiarisez ’huile concernant Recommandations’huile niveau du Vérification Ambiante TempératureSignification leur et internationaux Symboles Existent d’entorsesBijoux Moteur le Bois Hydraulique système du problème de cas EnLentement CylindreDépannage Hydraulique système du problème de case EnFeudense la de Entretien Saison hors RemisageMoteur Poulie Fente de couteau et Poutre Courroie la de ChangementHydraulique Huile Garantie la annulant Situations’utilisation Conseils Fendeuse la de ment -FonctionneFendeuse la de Utilisation Emploi chaque AvantFendeuse la de Arrêt Moteur du Commutateur Fendeuse la de marche en MiseDépart de Volet Démarreur du CordePoignée Fendeuse la de CommandesHydraulique soupape la de Manette MouvementFendeuse la de Montage Bloquer le etÉpingle-goupille Fendeuse la de Préparation Chaud Responsabilité VotreSeulement Responsabilité VotreFendeuse la sur sécurité de Étiquettes Sécurité de ÉtiquettesVente-après Service Modèle de numéro le trouver PourMatières des Table 25/07 03483-769 Important 5DM série la de Fendeuse

5DM specifications

MTD 5DM is an innovative work scheduling and management solution designed to streamline operations for businesses across various sectors. At its core, MTD 5DM aims to enhance productivity by offering advanced tools and features that cater to the complex demands of modern workplaces.

One of the standout features of MTD 5DM is its intuitive user interface. The platform is designed with user experience in mind, making it accessible for employees at all levels. This ease of navigation means that organizations can implement the system with minimal training, enabling rapid adoption and reducing downtime.

Another significant characteristic of MTD 5DM is its advanced scheduling capabilities. The system utilizes smart algorithms to optimize work schedules, taking into account various factors such as employee availability, skill sets, and project deadlines. This adaptability ensures that businesses can effectively allocate resources, minimizing any potential delays and enhancing operational efficiency.

MTD 5DM also integrates state-of-the-art cloud technology, allowing for real-time data access and updates. This enables teams to collaborate seamlessly, regardless of their physical locations. With cloud synchronization, all team members can stay informed and aligned on project statuses, fostering improved communication and teamwork.

In terms of analytics, MTD 5DM boasts robust reporting features that provide organizations with valuable insights into their operations. Advanced data analytics tools allow managers to monitor performance metrics, resource utilization, and employee productivity. This data-driven approach empowers businesses to make informed decisions, identify areas for improvement, and create strategies for future growth.

Security is a top priority for MTD 5DM. The platform employs cutting-edge encryption technologies to protect sensitive data, ensuring compliance with industry regulations and safeguarding against potential breaches. This commitment to security builds trust among users, enhancing the overall user experience.

Compatibility is another key feature of MTD 5DM. The platform can be seamlessly integrated with existing systems, enhancing its functionality and allowing businesses to leverage their current technology investments effectively. By providing interconnectivity with various software solutions, MTD 5DM becomes a versatile tool that adapts to the unique needs of each organization.

In summary, MTD 5DM is a comprehensive work management solution characterized by its user-friendly interface, advanced scheduling capabilities, cloud technology, robust analytics, stringent security measures, and compatibility with existing systems. By leveraging these features, businesses can optimize their operations, enhance productivity, and stay competitive in an ever-evolving marketplace.
Top Page Image Contents