MTD 5DM warranty Maintaining Your Engine, Air Cleaner Service, Spark Plug Service

Page 21

IMPORTANT: Used motor oil may cause skin cancer if repeatedly left in contact with the skin for prolonged periods. Although this is unlikely unless you handle used oil on a daily basis, it is still advisable to thoroughly wash your hands with soap and water as soon as possible after handling used oil.

NOTE: Please dispose of used motor oil in a manner that is compatible with the environment. We suggest you take it in a sealed container to your local service station for reclamation. Do not throw it in the trash or pour it on the ground.

Air Cleaner Service

Paper filters cannot be cleaned and must be replaced once a year or every 100 operating hours; more often if used in extremely dusty conditions.

WARNING: Never use gasoline or low flash point solvents for cleaning the air cleaner element. A fire or explosion could result.

IMPORTANT: Never run the engine without the air cleaner. Rapid engine wear will result.

1.Remove the wing bolt and the air cleaner cover. Remove the elements and separate them. See Figure 10-2. Replace paper element when dirty or damaged. Replace foam element when damaged.

2.To clean foam element, separate it from the paper element and wash in liquid detergent and water. Allow to dry thoroughly before using. Do not oil the foam element.

Spark Plug Service

WARNING: DO NOT check for spark with spark plug removed. DO NOT crank engine with spark plug removed.

To ensure proper engine operation, the spark plug must be properly gapped and free of deposits.

1.Remove the spark plug boot and use a spark plug wrench to remove the plug. See Figure 10-3.

WARNING: If the engine has been running, the muffler will be very hot. Be careful not to touch the muffler.

2.Visually inspect the spark plug. Discard the spark plug if there is apparent wear, or if the insulator is cracked or chipped. Clean the spark plug with a wire brush if it is to be reused.

3.Measure the plug gap with a feeler gauge. Correct as necessary by bending side electrode. See Figure 10-4. The gap should be set to 0.030 in.

Paper Element

Foam Element

Figure 10-2: Servicing the air cleaner.

Spark Plug

Spark Plug Boot

Figure 10-3: The spark plug and boot.

Electrode

0.030 in.

Figure 10-4: Measure the plug gap with a feeler gauge.

10

Maintaining

Your

Engine

WARNING

Never use gasoline or low flash point sol- vents for cleaning the air cleaner element. A fire or explosion could result.

DO NOT check for spark with spark plug removed. DO NOT crank engine with spark plug removed.

If the engine has been running, the muffler will be very hot. Be careful not to touch the muffler.

21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents Log Splitter Model Series 5DM 769-0348325/07 Table of Contents Finding and Recording Model NumberCustomer Support Safety Labels Found On Your Log Splitter Safety LabelsDo not adjust the pressure settings of the pump or valve Your ResponsibilityDo not check for leaks with your hand Average Useful Life Spark ArrestorAllow machine to cool at least 5 minutes before storing Use only your hand to operate the controlsHandling equipment Setting Up Your Log SplitterIs hot or running When handlingExtinguish ciga IgnitionKnow Your Log Splitter Operating Your Log SplitterStarter Rope Engine SwitchChoke Starting Log SplitterOperating Forward Your Log Splitter Using the Log SplitterStopping Log Splitter Before Each UseUse when fluid is below 20 F or above 150 F Use clean fluid and check fluid level regularlyOperating Tips AlwaysMaintaining Your Log Splitter Storing Your Log Splitter Clean the log splitter thoroughlyEngine Pulley Pump Idler Pulley Nut Replace spark plugCause Remedy Problem Cause RemedyService dealer Engine stalls during Low horsepower/weak engineConditions Low horsepower/weak engine Gear sections damagedCm below lowest portion of neck to allow for fuel expansion When transporting equipment, transport with fuel tankDo not choke carburetor to stop engine Do not overfill fuel tank. Fill tank to approximatelyInternational Symbols and Meanings Safety Label LocationKnow Your Engine Operating Your EngineThis engine is Pre-Operation CheckStarting The Engine Turn engine switch to onStopping The Engine Fuel RecommendationsMaintaining Your Oil ServiceOil Change TasksAir Cleaner Service Spark Plug ServiceMaintaining Your Engine Clean Engine StorageRemoving From Storage TWO Year Limited Warranty Model Series 5DM For parts and/or accessories refer to customer support on Parts List Pièces DétachéesMANUFACTURER’S Warranty Coverage EPA-1 Air à Filtre BougiesPropriétaire DU Responsabilités 24 CA-1-EPAANS Deux DE Limitée Garantie Moteur du Entretien Service en RemiseBougie la de Entretien Air à filtre du EntretienJamais N’utilisez Avertissement ’huile de Vidange ’essence panneFacilement plus coule Moteur du Arrêt Le concernant RecommandationsMoteur du marche en Mise CarburantMoteur le avec vous-Familiarisez ’huile concernant Recommandations’huile niveau du Vérification Ambiante TempératureSignification leur et internationaux Symboles Existent d’entorsesBijoux Moteur le Bois Hydraulique système du problème de cas EnLentement CylindreDépannage Hydraulique système du problème de case EnFeudense la de Entretien Saison hors RemisageMoteur Poulie Fente de couteau et Poutre Courroie la de ChangementHydraulique Huile Garantie la annulant Situations’utilisation Conseils Fendeuse la de ment -FonctionneFendeuse la de Utilisation Emploi chaque AvantFendeuse la de Arrêt Moteur du Commutateur Fendeuse la de marche en MiseDépart de Volet Démarreur du CordePoignée Fendeuse la de CommandesHydraulique soupape la de Manette MouvementFendeuse la de Montage Bloquer le etÉpingle-goupille Fendeuse la de Préparation Chaud Responsabilité VotreSeulement Responsabilité VotreFendeuse la sur sécurité de Étiquettes Sécurité de ÉtiquettesVente-après Service Modèle de numéro le trouver PourMatières des Table 25/07 03483-769 Important 5DM série la de Fendeuse

5DM specifications

MTD 5DM is an innovative work scheduling and management solution designed to streamline operations for businesses across various sectors. At its core, MTD 5DM aims to enhance productivity by offering advanced tools and features that cater to the complex demands of modern workplaces.

One of the standout features of MTD 5DM is its intuitive user interface. The platform is designed with user experience in mind, making it accessible for employees at all levels. This ease of navigation means that organizations can implement the system with minimal training, enabling rapid adoption and reducing downtime.

Another significant characteristic of MTD 5DM is its advanced scheduling capabilities. The system utilizes smart algorithms to optimize work schedules, taking into account various factors such as employee availability, skill sets, and project deadlines. This adaptability ensures that businesses can effectively allocate resources, minimizing any potential delays and enhancing operational efficiency.

MTD 5DM also integrates state-of-the-art cloud technology, allowing for real-time data access and updates. This enables teams to collaborate seamlessly, regardless of their physical locations. With cloud synchronization, all team members can stay informed and aligned on project statuses, fostering improved communication and teamwork.

In terms of analytics, MTD 5DM boasts robust reporting features that provide organizations with valuable insights into their operations. Advanced data analytics tools allow managers to monitor performance metrics, resource utilization, and employee productivity. This data-driven approach empowers businesses to make informed decisions, identify areas for improvement, and create strategies for future growth.

Security is a top priority for MTD 5DM. The platform employs cutting-edge encryption technologies to protect sensitive data, ensuring compliance with industry regulations and safeguarding against potential breaches. This commitment to security builds trust among users, enhancing the overall user experience.

Compatibility is another key feature of MTD 5DM. The platform can be seamlessly integrated with existing systems, enhancing its functionality and allowing businesses to leverage their current technology investments effectively. By providing interconnectivity with various software solutions, MTD 5DM becomes a versatile tool that adapts to the unique needs of each organization.

In summary, MTD 5DM is a comprehensive work management solution characterized by its user-friendly interface, advanced scheduling capabilities, cloud technology, robust analytics, stringent security measures, and compatibility with existing systems. By leveraging these features, businesses can optimize their operations, enhance productivity, and stay competitive in an ever-evolving marketplace.
Top Page Image Contents