MTD 5DM warranty Storing Your Log Splitter, Clean the log splitter thoroughly, Replace spark plug

Page 13

5.Chock both wheels, front and rear, and have your helper grasp the front of the unit and carefully tilt it back to expose the belt drive underneath.

IMPORTANT: To prevent engine oil from entering carburetor and/or hydraulic oil from escaping through the air vent hole, do not tilt unit to the side.

6.While your partner continues to hold the unit up, grasp the idler pulley nut with a 9/16 hex wrench or socket and pivot the idler bracket as shown in Figure 5-2. This will enable the belt to be easily removed from the idler pulley.

WARNING: Avoid the possibility of a pinching injury. Do not place your fingers on the idler spring or between the belt and a pulley while removing the belt.

7.Remove the belt from around the engine and pump pulleys.

8.Route the new belt around the three pulleys as shown in Figure 5-2.

NOTE: Idler bracket must pivot freely.

9.Have your partner lower unit and remount the belt cover removed earlier. Do not over tighten.

10.Remove piece of plastic from gas cap (if used).

11.Reconnect spark plug.

Storing Your Log Splitter

Prepare your log splitter for storage at the end of the season or if the log splitter will not be used for 30 days or more.

WARNING: Never store machine with fuel in the fuel tank inside of building where fumes may reach an open flame or spark, or where ignition sources

are present such as hot water and space heaters, furnaces, clothes dryers, stoves, electric motors, etc.

1. Clean the log splitter thoroughly.

NOTE: We do not recommend the use of pressure wash- ers or garden hose to clean your unit. They may cause damage to bearings or the engine. The use of water will result in shortened life and reduce serviceability.

Engine

Pulley

Pump

Pulley

Idler Pulley

Nut

Figure 5-2

2.Wipe unit with an oiled rag to prevent rust, especially on the wedge and the beam.

3.Drain fuel tank. Always drain fuel into approved container outdoors, away from open flame. Be sure that engine is cool before draining the fuel. Do not smoke while handling fuel.

4.Start the engine and let it run until the fuel lines and carburetor are empty.

5.Remove spark plug. Holding a rag over the cylinder hole, pour approximately 1/2 ounce (approximately one tablespoon) of engine oil into cylinder and crank slowly to distribute the oil.

6.Replace spark plug.

7.Do not store gasoline from one season to another.

8.Replace your gasoline can if it starts to rust. Rust and/or dirt in the gasoline will cause problems.

NOTE: For more information on storing the engine, refer to the Engine Maintenance section.

9.Store unit in a clean, dry area. Do not store next to corrosive materials, such as fertilizer. DO NOT store unit in upright position.

NOTE: If storing in an unventilated or metal storage shed, be certain to rustproof the equipment by coating with a light oil or silicone.

5

Maintaining

Your Log

Splitter

WARNING

Avoid the possibility of a pinching injury. Do not place your fingers on the idler spring or between the belt and a pulley while removing the belt.

Avoid the possibility of a pinching injury. Do not place your fingers on the idler spring or between the belt and a pulley while removing the belt.

13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents 769-03483 Log Splitter Model Series 5DM25/07 Finding and Recording Model Number Table of ContentsCustomer Support Safety Labels Found On Your Log Splitter Safety LabelsYour Responsibility Do not adjust the pressure settings of the pump or valveDo not check for leaks with your hand Average Useful Life Spark ArrestorAllow machine to cool at least 5 minutes before storing Use only your hand to operate the controlsHandling equipment Setting Up Your Log SplitterIs hot or running When handlingExtinguish ciga IgnitionKnow Your Log Splitter Operating Your Log SplitterStarter Rope Engine SwitchChoke Starting Log SplitterOperating Forward Your Log Splitter Using the Log SplitterStopping Log Splitter Before Each UseUse when fluid is below 20 F or above 150 F Use clean fluid and check fluid level regularlyOperating Tips AlwaysMaintaining Your Log Splitter Storing Your Log Splitter Clean the log splitter thoroughlyEngine Pulley Pump Idler Pulley Nut Replace spark plugCause Remedy Problem Cause RemedyService dealer Engine stalls during Low horsepower/weak engineConditions Low horsepower/weak engine Gear sections damagedCm below lowest portion of neck to allow for fuel expansion When transporting equipment, transport with fuel tankDo not choke carburetor to stop engine Do not overfill fuel tank. Fill tank to approximatelyInternational Symbols and Meanings Safety Label LocationKnow Your Engine Operating Your EngineThis engine is Pre-Operation CheckStarting The Engine Turn engine switch to onStopping The Engine Fuel RecommendationsMaintaining Your Oil ServiceOil Change TasksSpark Plug Service Air Cleaner ServiceMaintaining Your Engine Storage Clean EngineRemoving From Storage TWO Year Limited Warranty Model Series 5DM For parts and/or accessories refer to customer support on Parts List Pièces DétachéesMANUFACTURER’S Warranty Coverage EPA-1 Air à Filtre BougiesPropriétaire DU Responsabilités 24 CA-1-EPAANS Deux DE Limitée Garantie Moteur du Entretien Service en RemiseAir à filtre du Entretien Bougie la de EntretienJamais N’utilisez Avertissement ’essence panne ’huile de VidangeFacilement plus coule Moteur du Arrêt Le concernant RecommandationsMoteur du marche en Mise CarburantMoteur le avec vous-Familiarisez ’huile concernant Recommandations’huile niveau du Vérification Ambiante TempératureExistent d’entorses Signification leur et internationaux SymbolesBijoux Moteur le Bois Hydraulique système du problème de cas EnLentement CylindreDépannage Hydraulique système du problème de case EnSaison hors Remisage Feudense la de EntretienMoteur Poulie Fente de couteau et Poutre Courroie la de ChangementHydraulique Huile Garantie la annulant Situations’utilisation Conseils Fendeuse la de ment -FonctionneEmploi chaque Avant Fendeuse la de UtilisationFendeuse la de Arrêt Moteur du Commutateur Fendeuse la de marche en MiseDépart de Volet Démarreur du CordePoignée Fendeuse la de CommandesHydraulique soupape la de Manette MouvementBloquer le et Fendeuse la de MontageÉpingle-goupille Fendeuse la de Préparation Chaud Responsabilité VotreSeulement Responsabilité VotreFendeuse la sur sécurité de Étiquettes Sécurité de ÉtiquettesModèle de numéro le trouver Pour Vente-après ServiceMatières des Table 25/07 03483-769 Important 5DM série la de Fendeuse

5DM specifications

MTD 5DM is an innovative work scheduling and management solution designed to streamline operations for businesses across various sectors. At its core, MTD 5DM aims to enhance productivity by offering advanced tools and features that cater to the complex demands of modern workplaces.

One of the standout features of MTD 5DM is its intuitive user interface. The platform is designed with user experience in mind, making it accessible for employees at all levels. This ease of navigation means that organizations can implement the system with minimal training, enabling rapid adoption and reducing downtime.

Another significant characteristic of MTD 5DM is its advanced scheduling capabilities. The system utilizes smart algorithms to optimize work schedules, taking into account various factors such as employee availability, skill sets, and project deadlines. This adaptability ensures that businesses can effectively allocate resources, minimizing any potential delays and enhancing operational efficiency.

MTD 5DM also integrates state-of-the-art cloud technology, allowing for real-time data access and updates. This enables teams to collaborate seamlessly, regardless of their physical locations. With cloud synchronization, all team members can stay informed and aligned on project statuses, fostering improved communication and teamwork.

In terms of analytics, MTD 5DM boasts robust reporting features that provide organizations with valuable insights into their operations. Advanced data analytics tools allow managers to monitor performance metrics, resource utilization, and employee productivity. This data-driven approach empowers businesses to make informed decisions, identify areas for improvement, and create strategies for future growth.

Security is a top priority for MTD 5DM. The platform employs cutting-edge encryption technologies to protect sensitive data, ensuring compliance with industry regulations and safeguarding against potential breaches. This commitment to security builds trust among users, enhancing the overall user experience.

Compatibility is another key feature of MTD 5DM. The platform can be seamlessly integrated with existing systems, enhancing its functionality and allowing businesses to leverage their current technology investments effectively. By providing interconnectivity with various software solutions, MTD 5DM becomes a versatile tool that adapts to the unique needs of each organization.

In summary, MTD 5DM is a comprehensive work management solution characterized by its user-friendly interface, advanced scheduling capabilities, cloud technology, robust analytics, stringent security measures, and compatibility with existing systems. By leveraging these features, businesses can optimize their operations, enhance productivity, and stay competitive in an ever-evolving marketplace.
Top Page Image Contents