MTD 5DM Operating Forward Your Log Splitter, Stopping Log Splitter, Using the Log Splitter

Page 10

4

Neutral

Reverse

 

 

 

Operating Forward

Your Log

Splitter

Figure 4-5

WARNING

Never remove partially split wood from the wedge with your hands. Fingers may be- come trapped between split wood.

Stopping Log Splitter

1.Turn off the engine switch.

2.Disconnect spark plug wire and ground against the engine to prevent unintended starting.

3.Remove locking pin.

4.Return cylinder back to original position.

5.Place locking pin back into cylinder base to lock unit.

Before Each Use

1.Remove the oil plug and check hydraulic fluid level on level ground. Maintain fluid level to just below oil plug. Refill if necessary. Approved fluids include Dexron® III, or 10 weight AW hydraulic oil.

2.Check engine oil level. Refill if necessary.

3.Fill up gasoline if necessary.

4.Lubricate the beam area where cylinder will slide with engine oil. Do not use grease to lubricate. Make sure to lubricate both the top and bottom of the beam face.

5.Attach spark plug wire to the spark plug.

Using the Log Splitter

IMPORTANT: Always operate on level ground, otherwise fluid may be forced out through the air vent hole.

1.Block the front and back of both wheels.

2.Place the log against the splitting wedge. Only split wood in the direction of the grain.

3.Stabilize log, if needed, with your left hand on the side of the log only. Never place hand on the end between the log and the ram.

IMPORTANT: Only one adult should stabilize the log and operate the hydraulic valve control, so the operator has full control over the log and the ram.

4.Move hydraulic valve control FORWARD until ram touches log. Release the hydraulic valve control to NEUTRAL position to stop the ram movement. See Figure 4-5.

5.Remove your left hand from log. Move hydraulic valve control FORWARD to split log.

6.Move hydraulic valve control BACK to fully retract the ram to the locked position.

WARNING: Never remove partially split wood from the wedge with your hands. Fingers may become trapped between split wood.

10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents 769-03483 Log Splitter Model Series 5DM25/07 Finding and Recording Model Number Table of ContentsCustomer Support Safety Labels Safety Labels Found On Your Log SplitterYour Responsibility Do not adjust the pressure settings of the pump or valveDo not check for leaks with your hand Allow machine to cool at least 5 minutes before storing Spark ArrestorAverage Useful Life Use only your hand to operate the controlsSetting Up Your Log Splitter Handling equipmentExtinguish ciga When handlingIs hot or running IgnitionOperating Your Log Splitter Know Your Log SplitterChoke Engine SwitchStarter Rope Starting Log SplitterStopping Log Splitter Using the Log SplitterOperating Forward Your Log Splitter Before Each UseOperating Tips Use clean fluid and check fluid level regularlyUse when fluid is below 20 F or above 150 F AlwaysMaintaining Your Log Splitter Engine Pulley Pump Idler Pulley Nut Clean the log splitter thoroughlyStoring Your Log Splitter Replace spark plugProblem Cause Remedy Cause RemedyConditions Low horsepower/weak engine Engine stalls during Low horsepower/weak engineService dealer Gear sections damagedDo not choke carburetor to stop engine When transporting equipment, transport with fuel tankCm below lowest portion of neck to allow for fuel expansion Do not overfill fuel tank. Fill tank to approximatelySafety Label Location International Symbols and MeaningsThis engine is Operating Your EngineKnow Your Engine Pre-Operation CheckStopping The Engine Turn engine switch to onStarting The Engine Fuel RecommendationsOil Change Oil ServiceMaintaining Your TasksSpark Plug Service Air Cleaner ServiceMaintaining Your Engine Storage Clean EngineRemoving From Storage TWO Year Limited Warranty Model Series 5DM Parts List Pièces Détachées For parts and/or accessories refer to customer support onMANUFACTURER’S Warranty Coverage EPA-1 Bougies Air à Filtre24 CA-1-EPA Propriétaire DU ResponsabilitésANS Deux DE Limitée Garantie Service en Remise Moteur du EntretienAir à filtre du Entretien Bougie la de EntretienJamais N’utilisez Avertissement ’essence panne ’huile de VidangeFacilement plus coule Moteur du marche en Mise Le concernant RecommandationsMoteur du Arrêt Carburant’huile niveau du Vérification ’huile concernant RecommandationsMoteur le avec vous-Familiarisez Ambiante TempératureExistent d’entorses Signification leur et internationaux SymbolesBijoux Moteur le Lentement Hydraulique système du problème de cas EnBois CylindreHydraulique système du problème de case En DépannageSaison hors Remisage Feudense la de EntretienMoteur Poulie Hydraulique Huile Courroie la de ChangementFente de couteau et Poutre Garantie la annulant SituationsFendeuse la de ment -Fonctionne ’utilisation ConseilsEmploi chaque Avant Fendeuse la de UtilisationFendeuse la de Arrêt Départ de Volet Fendeuse la de marche en MiseMoteur du Commutateur Démarreur du CordeHydraulique soupape la de Manette Fendeuse la de CommandesPoignée MouvementBloquer le et Fendeuse la de MontageÉpingle-goupille Fendeuse la de Préparation Responsabilité Votre ChaudResponsabilité Votre SeulementSécurité de Étiquettes Fendeuse la sur sécurité de ÉtiquettesModèle de numéro le trouver Pour Vente-après ServiceMatières des Table Important 5DM série la de Fendeuse 25/07 03483-769

5DM specifications

MTD 5DM is an innovative work scheduling and management solution designed to streamline operations for businesses across various sectors. At its core, MTD 5DM aims to enhance productivity by offering advanced tools and features that cater to the complex demands of modern workplaces.

One of the standout features of MTD 5DM is its intuitive user interface. The platform is designed with user experience in mind, making it accessible for employees at all levels. This ease of navigation means that organizations can implement the system with minimal training, enabling rapid adoption and reducing downtime.

Another significant characteristic of MTD 5DM is its advanced scheduling capabilities. The system utilizes smart algorithms to optimize work schedules, taking into account various factors such as employee availability, skill sets, and project deadlines. This adaptability ensures that businesses can effectively allocate resources, minimizing any potential delays and enhancing operational efficiency.

MTD 5DM also integrates state-of-the-art cloud technology, allowing for real-time data access and updates. This enables teams to collaborate seamlessly, regardless of their physical locations. With cloud synchronization, all team members can stay informed and aligned on project statuses, fostering improved communication and teamwork.

In terms of analytics, MTD 5DM boasts robust reporting features that provide organizations with valuable insights into their operations. Advanced data analytics tools allow managers to monitor performance metrics, resource utilization, and employee productivity. This data-driven approach empowers businesses to make informed decisions, identify areas for improvement, and create strategies for future growth.

Security is a top priority for MTD 5DM. The platform employs cutting-edge encryption technologies to protect sensitive data, ensuring compliance with industry regulations and safeguarding against potential breaches. This commitment to security builds trust among users, enhancing the overall user experience.

Compatibility is another key feature of MTD 5DM. The platform can be seamlessly integrated with existing systems, enhancing its functionality and allowing businesses to leverage their current technology investments effectively. By providing interconnectivity with various software solutions, MTD 5DM becomes a versatile tool that adapts to the unique needs of each organization.

In summary, MTD 5DM is a comprehensive work management solution characterized by its user-friendly interface, advanced scheduling capabilities, cloud technology, robust analytics, stringent security measures, and compatibility with existing systems. By leveraging these features, businesses can optimize their operations, enhance productivity, and stay competitive in an ever-evolving marketplace.
Top Page Image Contents