MTD 5DM warranty Clean Engine, Removing From Storage

Page 22

10

Maintaining

Your

Engine

4.Check that the spark plug washer is in good condi- tion and thread the spark plug in by hand to prevent cross-threading.

5.After the spark plug is seated, tighten with a spark plug wrench to compress the washer.

NOTE: When installing a new spark plug, tighten 1/2 turn after the spark plug seats to compress the washer. When reinstalling a used spark plug, tighten 1/8-1/4 turn after the spark plug seats to compress the washer.

IMPORTANT: The spark plug must be securely tight- ened. An improperly tightened spark plug can become very hot and may damage the engine.

Storage

Engines stored over 30 days need to be drained of fuel to prevent deterioration and gum from forming in fuel system or on essential carburetor parts. If the gasoline in your engine deteriorates during storage, you may need to have the carburetor, and other fuel system components, serviced or replaced.

1.

Remove all fuel from tank by running engine until it

 

stops from lack of fuel.

2.

Change oil. See Oil Change section.

3.

Remove spark plug and pour about 1/2 an ounce of

 

engine oil into cylinder. Replace spark plug and crank

 

slowly to distribute oil.

4.

Clean debris from around engine, under finger guard,

 

and under, around and behind muffler. Touch up any

WARNING

Accumulation of debris around muffler could cause a fire. Inspect and clean before every use.

IMPORTANT

Do not spray engine with water to clean because water could contaminate fuel. Using a garden hose or pressure washing equipment can also force water into the air cleaner or muffler opening. Water in the air cleaner will soak the paper element, and water that passes through the element or muffler can enter the cylinder, causing damage.

Clean Engine

If the engine has been running, allow it to cool for at least half an hour before cleaning. Periodically remove dirt build-up from engine. Clean finger guard and around muffler. Clean with a brush or compressed air.

IMPORTANT: Do not spray engine with water to clean because water could contaminate fuel. Using a garden hose or pressure washing equipment can also force water into the air cleaner or muffler opening. Water in the air cleaner will soak the paper element, and water that passes through the element or muffler can enter the cylinder, causing damage.

WARNING: Accumulation of debris around muffler could cause a fire. Inspect and clean before every use.

 

damaged paint, and coat other areas that may rust with

 

a light film of oil.

5.

Store in a clean, dry and well ventilated area away from

 

any appliance that operates with a flame or pilot light,

 

such as a furnace, water heater, or clothes dryer. Also

 

avoid any area with a spark producing electric motor,

 

or where power tools are operated.

6.

If possible, also avoid storage areas with high humidity,

 

because that promotes rust and corrosion.

7.

Keep the engine level in storage. Tilting can cause fuel

 

or oil leakage.

Removing From Storage

1.Check your engine as described in the Pre-Operation Check section of this manual.

2.If the fuel was drained during storage preparation, fill the tank with fresh gasoline. If you keep a container of gasoline for refueling, make certain it contains only fresh fuel. Gasoline oxidizes and deteriorates over time, causing hard starting.

3.If the cylinder was coated with oil during storage preparation, the engine will smoke briefly at startup. This is normal.

22

Page 21 Page 23
Image 22
Page 21 Page 23
Contents 769-03483 Log Splitter Model Series 5DM25/07 Finding and Recording Model Number Table of ContentsCustomer Support Safety Labels Safety Labels Found On Your Log SplitterYour Responsibility Do not adjust the pressure settings of the pump or valveDo not check for leaks with your hand Allow machine to cool at least 5 minutes before storing Spark ArrestorAverage Useful Life Use only your hand to operate the controlsSetting Up Your Log Splitter Handling equipmentExtinguish ciga When handlingIs hot or running IgnitionOperating Your Log Splitter Know Your Log SplitterChoke Engine SwitchStarter Rope Starting Log SplitterStopping Log Splitter Using the Log SplitterOperating Forward Your Log Splitter Before Each UseOperating Tips Use clean fluid and check fluid level regularlyUse when fluid is below 20 F or above 150 F AlwaysMaintaining Your Log Splitter Engine Pulley Pump Idler Pulley Nut Clean the log splitter thoroughlyStoring Your Log Splitter Replace spark plugProblem Cause Remedy Cause RemedyConditions Low horsepower/weak engine Engine stalls during Low horsepower/weak engineService dealer Gear sections damagedDo not choke carburetor to stop engine When transporting equipment, transport with fuel tankCm below lowest portion of neck to allow for fuel expansion Do not overfill fuel tank. Fill tank to approximatelySafety Label Location International Symbols and MeaningsThis engine is Operating Your EngineKnow Your Engine Pre-Operation CheckStopping The Engine Turn engine switch to onStarting The Engine Fuel RecommendationsOil Change Oil ServiceMaintaining Your TasksSpark Plug Service Air Cleaner ServiceMaintaining Your Engine Storage Clean EngineRemoving From Storage TWO Year Limited Warranty Model Series 5DM Parts List Pièces Détachées For parts and/or accessories refer to customer support onMANUFACTURER’S Warranty Coverage EPA-1 Bougies Air à Filtre24 CA-1-EPA Propriétaire DU ResponsabilitésANS Deux DE Limitée Garantie Service en Remise Moteur du EntretienAir à filtre du Entretien Bougie la de EntretienJamais N’utilisez Avertissement ’essence panne ’huile de VidangeFacilement plus coule Moteur du marche en Mise Le concernant RecommandationsMoteur du Arrêt Carburant’huile niveau du Vérification ’huile concernant RecommandationsMoteur le avec vous-Familiarisez Ambiante TempératureExistent d’entorses Signification leur et internationaux SymbolesBijoux Moteur le Lentement Hydraulique système du problème de cas EnBois CylindreHydraulique système du problème de case En DépannageSaison hors Remisage Feudense la de EntretienMoteur Poulie Hydraulique Huile Courroie la de ChangementFente de couteau et Poutre Garantie la annulant SituationsFendeuse la de ment -Fonctionne ’utilisation ConseilsEmploi chaque Avant Fendeuse la de UtilisationFendeuse la de Arrêt Départ de Volet Fendeuse la de marche en MiseMoteur du Commutateur Démarreur du CordeHydraulique soupape la de Manette Fendeuse la de CommandesPoignée MouvementBloquer le et Fendeuse la de MontageÉpingle-goupille Fendeuse la de Préparation Responsabilité Votre ChaudResponsabilité Votre SeulementSécurité de Étiquettes Fendeuse la sur sécurité de ÉtiquettesModèle de numéro le trouver Pour Vente-après ServiceMatières des Table Important 5DM série la de Fendeuse 25/07 03483-769

5DM specifications

MTD 5DM is an innovative work scheduling and management solution designed to streamline operations for businesses across various sectors. At its core, MTD 5DM aims to enhance productivity by offering advanced tools and features that cater to the complex demands of modern workplaces.

One of the standout features of MTD 5DM is its intuitive user interface. The platform is designed with user experience in mind, making it accessible for employees at all levels. This ease of navigation means that organizations can implement the system with minimal training, enabling rapid adoption and reducing downtime.

Another significant characteristic of MTD 5DM is its advanced scheduling capabilities. The system utilizes smart algorithms to optimize work schedules, taking into account various factors such as employee availability, skill sets, and project deadlines. This adaptability ensures that businesses can effectively allocate resources, minimizing any potential delays and enhancing operational efficiency.

MTD 5DM also integrates state-of-the-art cloud technology, allowing for real-time data access and updates. This enables teams to collaborate seamlessly, regardless of their physical locations. With cloud synchronization, all team members can stay informed and aligned on project statuses, fostering improved communication and teamwork.

In terms of analytics, MTD 5DM boasts robust reporting features that provide organizations with valuable insights into their operations. Advanced data analytics tools allow managers to monitor performance metrics, resource utilization, and employee productivity. This data-driven approach empowers businesses to make informed decisions, identify areas for improvement, and create strategies for future growth.

Security is a top priority for MTD 5DM. The platform employs cutting-edge encryption technologies to protect sensitive data, ensuring compliance with industry regulations and safeguarding against potential breaches. This commitment to security builds trust among users, enhancing the overall user experience.

Compatibility is another key feature of MTD 5DM. The platform can be seamlessly integrated with existing systems, enhancing its functionality and allowing businesses to leverage their current technology investments effectively. By providing interconnectivity with various software solutions, MTD 5DM becomes a versatile tool that adapts to the unique needs of each organization.

In summary, MTD 5DM is a comprehensive work management solution characterized by its user-friendly interface, advanced scheduling capabilities, cloud technology, robust analytics, stringent security measures, and compatibility with existing systems. By leveraging these features, businesses can optimize their operations, enhance productivity, and stay competitive in an ever-evolving marketplace.
Top Page Image Contents