MTD 5DM Starting The Engine, Stopping The Engine, Fuel Recommendations, Turn engine switch to on

Page 19

2.Insert the dipstick into the engine block, but do not screw it in. See Figure 9-2.

3.If the level is low, slowly add oil to the upper limit on the dipstick.

4.Tighten dipstick firmly before starting engine.

IMPORTANT: Do not overfill. Overfilling with oil may cause smoking, hard starting, spark plug fouling, or oil saturation of air cleaner.

Fuel Recommendations

Use automotive gasoline (unleaded or low leaded to minimize combustion chamber deposits) with a minimum of 87 octane. Gasoline with up to 10% ethanol or 15% MTBE (Methyl Tertiary Butyl Ether) can be used. Never use an oil/gasoline mixture or dirty gasoline. Avoid getting dirt, dust, or water in the fuel tank. DO NOT use E85 gasoline.

WARNING: Gasoline is extremely flam- mable and is explosive under certain conditions.

Refuel in a well-ventilated area with the engine stopped. Do not smoke or allow flames or sparks in the area where the engine is refueled or where gasoline is stored.

Do not overfill the fuel tank (there should be no fuel in the filler neck). After refueling, make sure the tank cap is closed properly and securely.

Be careful not to spill fuel when refueling. Spilled fuel or fuel vapor may ignite. If any fuel is spilled, make sure the area is dry before starting the engine.

Avoid repeated or prolonged contact with skin or breathing of vapor.

Check Fuel Level

1.Clean around fuel fill before removing cap to fuel.

2.Fill tank to approximately one inch below lowest portion of neck to allow for fuel expansion. Be careful not to overfill.

IMPORTANT: Before refueling, allow engine to cool two minutes.

Starting The Engine

WARNING: Always keep hands and feet clear of equipment moving parts. Do not use a pressurized starting fluid. Vapors are flammable.

1.Check to make sure that cylinder is in the operating “Lock” position, engaging safety switch.

2.Pull out the choke knob located on the engine. See Figure 9-3 inset.

Oil Fill Cap/

Dipstick

Upper Level

Figure 9-2: Checking the oil level.

Figure 9-3: Starting the log splitter.

NOTE: Use of the choke may not be necessary if the engine is warm or the air temperature is high.

3.Turn engine switch to on.

4.Pull the starter grip lightly until resistance is felt, then pull rapidly to overcome compression, prevent kickback and start engine. See Figure 9-3. If engine does not start after ten seconds of repeated pulls, wait a few minutes and repeat.

IMPORTANT: Do not allow the starter grip to snap back against the rope guide. Return it gently to prevent damage to the starter.

5. When engine warms up, push in the choke knob.

Stopping The Engine

1. Turn off the engine switch.

9

Operating

Your

Engine

WARNING

Gasoline is extremely flammable and is explosive under certain conditions.

Always keep hands and feet clear of equipment moving parts. Do not use a pressurized starting fluid. Vapors are flam- mable.

19

Page 18 Page 20
Image 19
Page 18 Page 20
Contents 769-03483 Log Splitter Model Series 5DM25/07 Finding and Recording Model Number Table of ContentsCustomer Support Safety Labels Found On Your Log Splitter Safety LabelsYour Responsibility Do not adjust the pressure settings of the pump or valveDo not check for leaks with your hand Use only your hand to operate the controls Spark ArrestorAverage Useful Life Allow machine to cool at least 5 minutes before storingHandling equipment Setting Up Your Log SplitterIgnition When handlingIs hot or running Extinguish cigaKnow Your Log Splitter Operating Your Log SplitterStarting Log Splitter Engine SwitchStarter Rope ChokeBefore Each Use Using the Log SplitterOperating Forward Your Log Splitter Stopping Log SplitterAlways Use clean fluid and check fluid level regularlyUse when fluid is below 20 F or above 150 F Operating TipsMaintaining Your Log Splitter Replace spark plug Clean the log splitter thoroughlyStoring Your Log Splitter Engine Pulley Pump Idler Pulley NutCause Remedy Problem Cause RemedyGear sections damaged Engine stalls during Low horsepower/weak engineService dealer Conditions Low horsepower/weak engineDo not overfill fuel tank. Fill tank to approximately When transporting equipment, transport with fuel tankCm below lowest portion of neck to allow for fuel expansion Do not choke carburetor to stop engineInternational Symbols and Meanings Safety Label LocationPre-Operation Check Operating Your EngineKnow Your Engine This engine isFuel Recommendations Turn engine switch to onStarting The Engine Stopping The EngineTasks Oil ServiceMaintaining Your Oil ChangeSpark Plug Service Air Cleaner ServiceMaintaining Your Engine Storage Clean EngineRemoving From Storage TWO Year Limited Warranty Model Series 5DM For parts and/or accessories refer to customer support on Parts List Pièces DétachéesMANUFACTURER’S Warranty Coverage EPA-1 Air à Filtre BougiesPropriétaire DU Responsabilités 24 CA-1-EPAANS Deux DE Limitée Garantie Moteur du Entretien Service en RemiseAir à filtre du Entretien Bougie la de EntretienJamais N’utilisez Avertissement ’essence panne ’huile de VidangeFacilement plus coule Carburant Le concernant RecommandationsMoteur du Arrêt Moteur du marche en MiseAmbiante Température ’huile concernant RecommandationsMoteur le avec vous-Familiarisez ’huile niveau du VérificationExistent d’entorses Signification leur et internationaux SymbolesBijoux Moteur le Cylindre Hydraulique système du problème de cas EnBois LentementDépannage Hydraulique système du problème de case EnSaison hors Remisage Feudense la de EntretienMoteur Poulie Garantie la annulant Situations Courroie la de ChangementFente de couteau et Poutre Hydraulique Huile’utilisation Conseils Fendeuse la de ment -FonctionneEmploi chaque Avant Fendeuse la de UtilisationFendeuse la de Arrêt Démarreur du Corde Fendeuse la de marche en MiseMoteur du Commutateur Départ de VoletMouvement Fendeuse la de CommandesPoignée Hydraulique soupape la de ManetteBloquer le et Fendeuse la de MontageÉpingle-goupille Fendeuse la de Préparation Chaud Responsabilité VotreSeulement Responsabilité VotreFendeuse la sur sécurité de Étiquettes Sécurité de ÉtiquettesModèle de numéro le trouver Pour Vente-après ServiceMatières des Table 25/07 03483-769 Important 5DM série la de Fendeuse

5DM specifications

MTD 5DM is an innovative work scheduling and management solution designed to streamline operations for businesses across various sectors. At its core, MTD 5DM aims to enhance productivity by offering advanced tools and features that cater to the complex demands of modern workplaces.

One of the standout features of MTD 5DM is its intuitive user interface. The platform is designed with user experience in mind, making it accessible for employees at all levels. This ease of navigation means that organizations can implement the system with minimal training, enabling rapid adoption and reducing downtime.

Another significant characteristic of MTD 5DM is its advanced scheduling capabilities. The system utilizes smart algorithms to optimize work schedules, taking into account various factors such as employee availability, skill sets, and project deadlines. This adaptability ensures that businesses can effectively allocate resources, minimizing any potential delays and enhancing operational efficiency.

MTD 5DM also integrates state-of-the-art cloud technology, allowing for real-time data access and updates. This enables teams to collaborate seamlessly, regardless of their physical locations. With cloud synchronization, all team members can stay informed and aligned on project statuses, fostering improved communication and teamwork.

In terms of analytics, MTD 5DM boasts robust reporting features that provide organizations with valuable insights into their operations. Advanced data analytics tools allow managers to monitor performance metrics, resource utilization, and employee productivity. This data-driven approach empowers businesses to make informed decisions, identify areas for improvement, and create strategies for future growth.

Security is a top priority for MTD 5DM. The platform employs cutting-edge encryption technologies to protect sensitive data, ensuring compliance with industry regulations and safeguarding against potential breaches. This commitment to security builds trust among users, enhancing the overall user experience.

Compatibility is another key feature of MTD 5DM. The platform can be seamlessly integrated with existing systems, enhancing its functionality and allowing businesses to leverage their current technology investments effectively. By providing interconnectivity with various software solutions, MTD 5DM becomes a versatile tool that adapts to the unique needs of each organization.

In summary, MTD 5DM is a comprehensive work management solution characterized by its user-friendly interface, advanced scheduling capabilities, cloud technology, robust analytics, stringent security measures, and compatibility with existing systems. By leveraging these features, businesses can optimize their operations, enhance productivity, and stay competitive in an ever-evolving marketplace.
Top Page Image Contents