MB QUART SCR manual Forward Travel, Reverse Travel

Page 15

Section 4

In case of an emergency, such as loss of control, stop the mower’s movement by quickly pulling the forward speed control lever to the neutral position.

Forward Travel

-NOTE-

Use one hand on both steering levers as shown in Figure 4-4 to minimize overcontrol.

To travel forward with the mower, move the speed control lever forward. Do not push the steering control levers forward as they are used only for steering the mower left or right. When the speed control is moved forward, the mower will travel forward at the speed the control lever is set at. To increase the speed, push the control lever forward and to decrease the speed, pull the control lever back. It is not necessary to hold the speed control in position, since a friction system holds the lever in position.

To stop the forward travel, pull the speed control lever back to the neutral position.

To steer the mower left while traveling forward, pull the left steering lever back. The further the lever is pulled back, the sharper the mower will turn left.

To steer the mower right while traveling forward, pull the right steering control lever back. The further the lever is pulled back, the sharper the mower will turn right.

-NOTE-

Smooth operation of the steering levers will produce a smooth mower operation. While learning the operation of the steering controls, keep the travel speed low.

-IMPORTANT-

Do not travel forward over a curb. The mower will hang up on the curb. Tilt the deck and travel backwards over the curb at a 45 degree angle. (See section 4.15 for cutter deck tilting instructions)

Reverse Travel

SCR 2K HOC

Figure 4-4 Hands On Controls

CAUTION:

Before backing up, observe the rear for persons and obstructions. Clear the area before backing up. Possible injury or property damage could occur.

CAUTION:

Disengage power to the mower before backing up. Do not mow in reverse unless absolutely necessary and then only after observation of the entire area behind the mower.

To travel in reverse, pull both handles all the way back. Keep the travel speed low while traveling in reverse.

-NOTE-

The mower will not travel straight in reverse. Slight adjustments must be made using the steering controls.

13

Image 15
Contents OPERATOR’S Manual Remember Your Mower is only AS Safe AS the Operator Servicing the Engine and Drive Train Components General InformationIntroduction Direction ReferenceISO Symbols CE Mark Symboldescription Safety Information Signal WordsBefore Operation Considerations Operation Considerations Maintenance Considerations Read Operators Manual Tractor SpecificationsEngine ElectricalGrass Catching System Weights and DimensionsTractor Contd Cutter DeckControls and Instrument Identification Operating InstructionsDump Valves Location Safety Interlock SystemGround Travel and Steering Starting the EngineReverse Travel Forward TravelHillside Operation Engaging the Deck Drive Cutter BladesHOPPER, Mulch or Side Discharge Operation Parking the MowerAfter Operation 10 Tailgate Operation Grass Catching OperationMulching Operation Side Discharge OperationRemoving Clogged Material Adjusting Cutting Height Moving Mower with Engine StoppedRecommendations for Mowing 15 Deck Locking Pin Tilting the Cutter DeckCondition Cause Cure Troubleshooting Cutting ConditionsScalloped Cut, or Rough Contour Troubleshooting Contd Condition Cause CureGround Troubleshooting ContdParking Brake Adjustment AdjustmentsTravel Adjustments Neutral AdjustmentDrive linkage Tracking AdjustmentBelt Alignment Cutter Deck Engagement Belt AdjustmentThrottle Control and Choke Adjustment Belt AdjustmentCutter Deck Adjustments Maintenance Chart Recommended Service Intervals MaintenanceLubrication Grease Fitting Lubrication Chart see Figure Maintenance Chart Recommended Service Intervals ContdRight Side Under Seat Checking Hydraulic Oil Level Checking Engine Crankcase Oil LevelChanging Hydraulic Oil Filling the Fuel Tank Changing Engine Crankcase OilChanging Engine Oil Filter Engine Fuel SystemCleaning and/or Replacing Air Cleaner Element BatteryChecking Electrolyte Level and Cleaning Battery Engine AIR CleanerJump Starting Charging the BatteryCutter Blades Blade ReplacementDrive Belts Blade SharpeningChecking Lubricant Level TiresHopper Cutter Deck Gearbox10 Gearbox Drain Plug Power Unit Gearbox13 Fluid Level BODY, DECK, Hopper and UpholsteryPage Cutter Decks Number Description Cutter DecksCutter Deck Support Components Cutter Deck Support Components Sheet Metal Sheet Metal Blower Assembly Blower Assembly Part Engine Engine and Attaching Parts Traction Drive Components Part Description Hydraulic Pump Housing Kit Includes Housing, Journal Bearing Cutter Deck Drive Gearbox Ref. Part No. No. Description Speed and Steering Controls Part Description Parking Brake Mechanism Parking Brake Mechanism Fuel and Hydraulic Components Ref. Part No. Number Description Kohler Electrical System Part Number Description Kawasaki Electrical System Kawasaki Electrical System Hopper Hopper Hopper Actuator Mechanism Ref. Part No. Number Description Cutting Height Replacement Decals and Information PlatesSCR 2K RD2 Kohler Electrical Schematic Limited Warranty Commercial Equipment 2002 Kawasaki Electrical Schematic