MB QUART SCR manual Tilting the Cutter Deck, Deck Locking Pin

Page 21

Section 4

4.15 TILTING THE CUTTER DECK

WARNING:

Do not tilt the mower deck with the mower blades rotating. Shut off the engine and remove the ignition key. Bodily injury could occur from the rotating blades.

The mower deck can be tilted up for trailering, blade replacement, etc. To tilt the deck up:

1.Shut off the engine, remove the ignition key and engage the park brake.

Deck Locking

Pin

Locking Pin Hole

SCR 2K DLP

Figure 4-15 Deck Locking Pin

2.Lift up on the caster wheel arm until the lock pin engages into the lock pin hole (Figure 4-15).

3.To release the deck and lower it to its operating position:

A.Lift up on the caster wheel arm while pulling up on the lock pin.

B.Carefully lower the deck to the ground.

19

Image 21
Contents OPERATOR’S Manual Remember Your Mower is only AS Safe AS the Operator Introduction General InformationDirection Reference Servicing the Engine and Drive Train ComponentsISO Symbols CE Mark Symboldescription Safety Information Signal WordsBefore Operation Considerations Operation Considerations Maintenance Considerations Read Operators Manual Engine SpecificationsElectrical TractorTractor Contd Weights and DimensionsCutter Deck Grass Catching SystemControls and Instrument Identification Operating InstructionsDump Valves Location Safety Interlock SystemGround Travel and Steering Starting the EngineReverse Travel Forward TravelHillside Operation Engaging the Deck Drive Cutter BladesHOPPER, Mulch or Side Discharge Operation Parking the MowerAfter Operation 10 Tailgate Operation Grass Catching OperationMulching Operation Side Discharge OperationRemoving Clogged Material Adjusting Cutting Height Moving Mower with Engine StoppedRecommendations for Mowing 15 Deck Locking Pin Tilting the Cutter DeckCondition Cause Cure Troubleshooting Cutting ConditionsScalloped Cut, or Rough Contour Troubleshooting Contd Condition Cause CureGround Troubleshooting ContdParking Brake Adjustment AdjustmentsTravel Adjustments Neutral AdjustmentDrive linkage Tracking AdjustmentThrottle Control and Choke Adjustment Cutter Deck Engagement Belt AdjustmentBelt Adjustment Belt AlignmentCutter Deck Adjustments Maintenance Chart Recommended Service Intervals MaintenanceLubrication Grease Fitting Lubrication Chart see Figure Maintenance Chart Recommended Service Intervals ContdRight Side Under Seat Checking Hydraulic Oil Level Checking Engine Crankcase Oil LevelChanging Hydraulic Oil Changing Engine Oil Filter Changing Engine Crankcase OilEngine Fuel System Filling the Fuel TankChecking Electrolyte Level and Cleaning Battery BatteryEngine AIR Cleaner Cleaning and/or Replacing Air Cleaner ElementJump Starting Charging the BatteryDrive Belts Blade ReplacementBlade Sharpening Cutter BladesHopper TiresCutter Deck Gearbox Checking Lubricant Level10 Gearbox Drain Plug Power Unit Gearbox13 Fluid Level BODY, DECK, Hopper and UpholsteryPage Cutter Decks Number Description Cutter DecksCutter Deck Support Components Cutter Deck Support Components Sheet Metal Sheet Metal Blower Assembly Blower Assembly Part Engine Engine and Attaching Parts Traction Drive Components Part Description Hydraulic Pump Housing Kit Includes Housing, Journal Bearing Cutter Deck Drive Gearbox Ref. Part No. No. Description Speed and Steering Controls Part Description Parking Brake Mechanism Parking Brake Mechanism Fuel and Hydraulic Components Ref. Part No. Number Description Kohler Electrical System Part Number Description Kawasaki Electrical System Kawasaki Electrical System Hopper Hopper Hopper Actuator Mechanism Ref. Part No. Number Description Cutting Height Replacement Decals and Information PlatesSCR 2K RD2 Kohler Electrical Schematic Limited Warranty Commercial Equipment 2002 Kawasaki Electrical Schematic