MB QUART SCR manual Neutral Adjustment, Travel Adjustments

Page 26

R

Section 6

1/16"

SCR 2K BAR

Spring Housing

Figure 6-3 Brake Actuator Rod Assembly

CAUTION:

Stop the engine and remove the key from the ignition before making any adjustments. Wait for all moving parts to come to a complete stop before beginning work.

CAUTION:

The engine and drive unit can get hot during operation causing burn injuries. Allow engine and drive components to cool before making any adjustments.

Neutral Adjustment

-IMPORTANT-

Before proceeding with this adjustment, be sure that the tire pressure is correct, that the caster wheels turn freely, and that the transmission drive belt tension spring is not broken.

1.Jack up the machine enough to lift the drive wheels and block securely.

2.Pull the speed control lever into the neutral position.

6.2 TRAVEL ADJUSTMENTS

Neutral or tracking adjustments will need to be made if:

A.The speed control lever is in neutral and the machine creeps forward or backward. (Neutral Adjustment)

B.The mower pulls to one side or the other when traveling in a forward direction. (Tracking Adjustment).

If the mower creeps forward or backward as indicated in "A" above, the neutral linkages must be adjusted. Start with adjusting the speed control lever and proceed as directed. To correct the tracking of the mower (mower pulls to one side when traveling in a forward direction), adjust the tracking of the mower as described on page 23.

3.Pull the park brake lever into the fully engaged position.

4.Adjust the speed control lever turnbuckle until the speed control lever contacts the park brake lever and tighten the jam nuts. (See Figure 6-4).

 

Speed Control

 

Linkage

Speed Control

 

Lever

No Gap

No Gap

 

 

Brake Lever

SCR 2K CDA

Figure 6-4 Speed Control Lever

24

Page 25 Page 27
Image 26
Page 25 Page 27
Contents OPERATOR’S Manual Remember Your Mower is only AS Safe AS the Operator Direction Reference General InformationIntroduction Servicing the Engine and Drive Train ComponentsISO Symbols CE Mark Symboldescription Before Operation Considerations Safety InformationSignal Words Operation Considerations Maintenance Considerations Read Operators Manual Electrical SpecificationsEngine TractorCutter Deck Weights and DimensionsTractor Contd Grass Catching SystemOperating Instructions Controls and Instrument IdentificationSafety Interlock System Dump Valves LocationStarting the Engine Ground Travel and SteeringForward Travel Reverse TravelEngaging the Deck Drive Cutter Blades Hillside OperationAfter Operation HOPPER, Mulch or Side Discharge OperationParking the Mower Grass Catching Operation 10 Tailgate OperationRemoving Clogged Material Mulching OperationSide Discharge Operation Recommendations for Mowing Adjusting Cutting HeightMoving Mower with Engine Stopped Tilting the Cutter Deck 15 Deck Locking PinTroubleshooting Cutting Conditions Condition Cause CureTroubleshooting Contd Condition Cause Cure Scalloped Cut, or Rough ContourTroubleshooting Contd GroundAdjustments Parking Brake AdjustmentNeutral Adjustment Travel AdjustmentsTracking Adjustment Drive linkageBelt Adjustment Cutter Deck Engagement Belt AdjustmentThrottle Control and Choke Adjustment Belt AlignmentCutter Deck Adjustments Maintenance Maintenance Chart Recommended Service IntervalsMaintenance Chart Recommended Service Intervals Contd Lubrication Grease Fitting Lubrication Chart see FigureRight Side Under Seat Changing Hydraulic Oil Checking Hydraulic Oil LevelChecking Engine Crankcase Oil Level Engine Fuel System Changing Engine Crankcase OilChanging Engine Oil Filter Filling the Fuel TankEngine AIR Cleaner BatteryChecking Electrolyte Level and Cleaning Battery Cleaning and/or Replacing Air Cleaner ElementCharging the Battery Jump StartingBlade Sharpening Blade ReplacementDrive Belts Cutter BladesCutter Deck Gearbox TiresHopper Checking Lubricant LevelPower Unit Gearbox 10 Gearbox Drain PlugBODY, DECK, Hopper and Upholstery 13 Fluid LevelPage Cutter Decks Cutter Decks Number DescriptionCutter Deck Support Components Cutter Deck Support Components Sheet Metal Sheet Metal Blower Assembly Blower Assembly Part Engine Engine and Attaching Parts Traction Drive Components Part Description Hydraulic Pump Housing Kit Includes Housing, Journal Bearing Cutter Deck Drive Gearbox Ref. Part No. No. Description Speed and Steering Controls Part Description Parking Brake Mechanism Parking Brake Mechanism Fuel and Hydraulic Components Ref. Part No. Number Description Kohler Electrical System Part Number Description Kawasaki Electrical System Kawasaki Electrical System Hopper Hopper Hopper Actuator Mechanism Ref. Part No. Number Description Replacement Decals and Information Plates Cutting HeightSCR 2K RD2 Kohler Electrical Schematic Limited Warranty Commercial Equipment 2002 Kawasaki Electrical Schematic
Top Page Image Contents