Land Pride AFM4211 manual Hydraulic Hook-up, Pull Rope Hook-up, Gauge Wheel Assembly

Page 16

Table of Contents

Section 1: Assembly and Set-up

Land Pride

Hydraulic Hook-up

Refer to Figure 1-4:

This mower is equipped and plumbed from the factory with double acting cylinders, hydraulic hoses and couplings for folding the wings and center deck.

1.Cut plastic ties securing hydraulic hoses (#1) to hose support loop (#2). Be careful not to cut plastic tie securing the ten linch pins (#5) to the support loop.

2.Route hoses (#1) through hose support loop (#2) and connect to tractor remote outlets. Quick disconnect hydraulic fittings for your tractor are supplied attached to the hoses.

3.Locate carbon steel wire (#3) attached between wing cylinders (#4). This wire secures the wing decks in the folded position during shipment. Remove wire and dispose of it in a trash container.

Pull Rope Hook-up

Refer to Figure 1-5:

The operator on the tractor seat will need to be able to access the pull rope from the tractor seat when lowering the folded decks to ground level.

1.Attach pull rope (#1) to an area within the operator’s reach. Make sure the pull rope can not become tangled with the operator and driveline.

2.Unfold mower decks as follows:

a.Retract hydraulic cylinders to remove weight from transport locks.

b.Pull transport lock rope (#1) toward the tractor to disengage locks.

c.Hold locks in this position until all 3 mower decks have unfolded enough to allow lock lugs to become fully disengaged.

d.Extend all 3 cylinders to their maximum stroke.

Gauge Wheel Assembly

Refer to Figure 1-6:

IMPORTANT: Do not bend spring steel mounting bracket supporting the slow moving vehicle sign. This sign is purposely angled so that when the deck is folded up for transporting, the sign will face traffic.

Center deck gauge wheels (#1) are mounted in the carrier frames spindle support tubes upside down.

1.Remove nuts (#6) and bolts (#5) from the center deck carrier frames and remove gauge wheels from the frames.

2.Check spacer location on the other gauge wheels. Note how many and what sizes are above and below the gauge wheel spindle support tube and then place an equal number of spacers (#2, 3 & 4) and sizes above and below the spindle support tube while inserting the gauge wheel spindle into the spindle support tubes.

26622

Hydraulic Hook-up

Figure 1-4

Spring Loaded

Transport Locks

1

13660

Pull Ropes

Figure 1-5

Leave Slow Moving Vehicle Sign angled.

 

This sign should face traffic when deck

 

is folded up for transporting.

26880

Center Deck Rear Gauge Wheels

Figure 1-6

14 AFM4211 All-Flex Mowers 315-507M

11/14/08

Page 15 Page 17
Image 16
Page 15 Page 17
Contents All-Flex Mowers Table of Contents Safety at All Times Practice Safe Maintenance Use a Safety ChainTransport Machinery Safely Tire Safety Wear Protective EquipmentAvoid High Pressure Fluids Hazard Keep Riders Off MachinerySafety Labels 818-339C818-019C 818-561C818-337C 818-130C818-045C 818-552C 818-556C818-555C 818-003C 838-345C838-270C 818-543C0818-187C 818-229C 818-230C818-540C Application Using This ManualOwner Assistance Tractor Requirements Hardware Torque InformationPTO To Drawbar Set-Up Tractor Hook-upCheck Constant Velocity Driveline Length Main Driveline InstallationDriveline Shortening Hydraulic Hook-up Gauge Wheel AssemblyPull Rope Hook-up Bleeding Hydraulics Transport Fold Hydraulic PlumbingIntroduction Joint TimingTransporting Joint TimingConstant Velocity Driveline Angle Pre-Operation InstructionsOperating Instructions Table of Contents Center Deck Height Adjustments Cutting Height ChartBelt Tension Ball Swivel Hitch Accessory Part NumbersCutting Blades Maintenance Blade PlacementServicing Mower Blades Blade InspectionBlade Rotation Blade Removal And InstallationBlade Removal Belt Installation Blade SharpeningBlade Options Blade SharpeningClutch Disassembly, Inspection & Assembly Driveline ProtectionType a Clutches Clutch Run-In Clutch TypesPlate Disassembly Step Plate Assembly StepDisassembly and Assembly Type B Clutch AssemblyType B Clutch Clutch Run-In Hex Head Socket BoltsStorage Tires With Air PressureLubrication HoursDriveline Constant Velocity Shaft Driveline ShaftsWheel Support Bushings Wheel Bushings Gauge WheelsWheel Bushings Transport Hubs Blade Spindle Bearings, Center DeckRequired Way GearboxMower Deck Gearbox Blade Spindle Bearings, Wing DecksTransport Locks Wing Deck Pivot BushingsRear Deck Pivot Half Clamps Wing Flex Pivot LugsSpecification / Capacity AFM4211 All-Flex Grooming MowersTable of Contents Features Benefits Problem Cause Solution Discharge openings plugged Belt slippingPatches of uncut grass Gearbox noisyTire Inflation Chart Torque Values ChartAdditional Torque Values 40 AFM4211 All-Flex Mowers 315-507M Warranty Overall Unit and Drivelines One year Parts and LaborCorporate Office P.O. Box 5060 Salina, Kansas 67402-5060 USA
Related manuals
Manual 82 pages 29.47 Kb
Top Page Image Contents