Land Pride Official Lawn Mower Manual for your AFM4211: Assembly, Setup, and Safety

Page 15

Land PrideTable of Contents

Section 1: Assembly and Set-up

Main Driveline Installation

!WARNING!

Damaged drivelines can cause serious injury or death.

!CAUTION!

Tractor PTO shield and all Grooming Mower guards must be in place at all times during operation!

!CAUTION!

Always engage parking brake, shut off tractor and remove key before dismounting from tractor.

IMPORTANT: The driveline must be lubricated before putting it into service. Refer to “Lubrication” on page 30.

IMPORTANT: Some tractors are equipped with multispeed PTO ranges. Be certain your tractor ‘s PTO is set for 540 rpm.

Always engage PTO at low engine rpm to minimize start-up torque on driveline. Drivelines with friction clutches must go through a “run-in” operation prior to initial use and after long periods of inactivity. See “Driveline Protection” on page 26” for a detailed run-in description.

Check Constant Velocity Driveline Length

IMPORTANT: Always check driveline length during initial setup and when connecting to a different tractor. Too long a driveline can damage tractor, gearbox and the driveline.

23557

Refer to Figure 1-3

1.Place tractor gear selector in park, shut tractor engine off, set park brake and remove switch key.

2.Attach driveline to mower and tractor as follows:

a.Slide inner yoke of driveline over mower gearbox shaft and secure with locking collar.

b.Slide outer yoke with constant velocity joint over tractor PTO shaft and secure with locking collar.

c.Skip to Step 4 if driveline fits between tractor and Grooming Mower.

3.The driveline will require shortening if it is too long to fit between the tractor and Grooming Mower. Shorten driveline as follows:

a.Pull driveline profiles apart into two sections as shown in Figure 1-3.

b.Attach outer driveline universal joint to tractor PTO shaft and inner driveline universal joint to gearbox shaft. Pull on each driveline section to be sure universal joints are secured.

c.Hold driveline sections parallel to each other to determine if they are too long. The inner and outer shields on each section should end approximately 1" short of reaching the universal joint shield on the adjacent section (see “B” dimension). If they are too long, measure 1" (“B” dimension) back from the universal joint shield and make a mark at this location on the inner and outer shields.

d.Cut off inner shield at mark (“X” dimension). Cut same amount off inner shaft (“X1” dimension). Repeat cut off procedure (“Y” & “Y1” dimensions) to cut outer driveline half.

e.Remove all burrs and cuttings.

4.With driveline profiles pulled apart, apply multi-purpose grease to the inside of the outer profile and then reassemble the two profiles.

5.Attach inner driveline yoke to gearbox shaft and outer driveline yoke to tractor's PTO shaft.

6.The driveline should now be moved back and forth to insure that both ends are secured. Reattach any end that is loose.

IMPORTANT: Two small chains supplied with the driveline must be attached to restrict driveline shield rotation.

7.Hook a safety chain in the hole on the outer driveline yoke shield and its opposite end to the tractor.

8.Hook the other safety chain in the hole on the inner driveline yoke shield and its opposite end to the mower.

Driveline Shortening

Figure 1-3

11/14/08

AFM4211 All-Flex Mowers 315-507M

13

Image 15
Contents All-Flex Mowers Table of Contents Safety at All Times Use a Safety Chain Practice Safe MaintenanceTransport Machinery Safely Keep Riders Off Machinery Tire SafetyWear Protective Equipment Avoid High Pressure Fluids Hazard818-339C Safety Labels818-561C 818-019C818-130C 818-337C818-552C 818-556C 818-045C818-555C 818-543C 818-003C838-345C 838-270C818-230C 0818-187C 818-229C818-540C Using This Manual ApplicationOwner Assistance Tractor Hook-up Tractor RequirementsHardware Torque Information PTO To Drawbar Set-UpMain Driveline Installation Check Constant Velocity Driveline LengthDriveline Shortening Gauge Wheel Assembly Hydraulic Hook-upPull Rope Hook-up Transport Fold Hydraulic Plumbing Bleeding HydraulicsJoint Timing IntroductionJoint Timing TransportingPre-Operation Instructions Constant Velocity Driveline AngleOperating Instructions Table of Contents Cutting Height Chart Center Deck Height AdjustmentsBelt Tension Accessory Part Numbers Ball Swivel HitchCutting Blades Blade Inspection MaintenanceBlade Placement Servicing Mower BladesBlade Removal And Installation Blade RotationBlade Removal Blade Sharpening Belt InstallationBlade Sharpening Blade OptionsClutch Types Clutch Disassembly, Inspection & AssemblyDriveline Protection Type a Clutches Clutch Run-InPlate Assembly Step Plate Disassembly StepHex Head Socket Bolts Disassembly and AssemblyType B Clutch Assembly Type B Clutch Clutch Run-InTires With Air Pressure StorageDriveline Shafts LubricationHours Driveline Constant Velocity ShaftBlade Spindle Bearings, Center Deck Wheel Support BushingsWheel Bushings Gauge Wheels Wheel Bushings Transport HubsBlade Spindle Bearings, Wing Decks RequiredWay Gearbox Mower Deck GearboxWing Flex Pivot Lugs Transport LocksWing Deck Pivot Bushings Rear Deck Pivot Half ClampsAFM4211 All-Flex Grooming Mowers Specification / CapacityTable of Contents Features Benefits Problem Cause Solution Gearbox noisy Discharge openings pluggedBelt slipping Patches of uncut grassTorque Values Chart Tire Inflation ChartAdditional Torque Values 40 AFM4211 All-Flex Mowers 315-507M Overall Unit and Drivelines One year Parts and Labor WarrantyCorporate Office P.O. Box 5060 Salina, Kansas 67402-5060 USA
Related manuals
Manual 82 pages 29.47 Kb