Land Pride AFM4211 manual Safety at All Times

Page 3

Land Pride

Table of Contents

Important Safety Information

These are common practices that may or may not be applicable to the products described in this manual.

Safety at All Times

Thoroughly read and understand the instructions given in this manual before operation. Refer to the “Safety Label” section, read all instructions noted on them.

Do not allow anyone to operate this equipment who has not fully read and comprehended this manual and who has not been properly trained in the safe operation of the equipment.

Look For The Safety Alert Symbol

The SAFETY ALERT SYMBOL indicates there is a

!safety precaution must be taken. When you see this symbol, be alert and carefully read the message that follows it. In addition to design and configuration of equipment, hazard control and accident prevention are dependent upon the awareness, concern, prudence and proper training of personnel involved in

the operation, transport, maintenance and storage of equipment.potential hazard to personal safety involved and extra

Operator should be familiar with

all functions of the unit.

Operate implement from the

driver’s seat only.

Make sure all guards and shields

are in place and secured before

operating implement.

Do not leave tractor or implement

unattended with engine running.

Dismounting from a moving

tractor could cause serious injury

or death.

Do not allow anyone to stand

between the tractor and

implement while backing up to the

implement.

Keep hands, feet, and clothing

away from power-driven parts.

Wear snug fitting clothing to avoid

entanglement with moving parts.

Watch out for wires, trees, etc.,

Be Aware of

Signal Words

A Signal word designates a degree or level of hazard seriousness. The signal words are:

!DANGER

Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. This signal word is limited to the most extreme situations, typically for machine components that, for functional purposes, cannot be guarded.

!WARNING

Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury, and includes hazards that are exposed when guards are removed. It may also be used to alert against unsafe practices.

!CAUTION

Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury. It may also be used to alert against unsafe practices.

when raising implement. Make

sure all persons are clear of

working area.

Turning tractor too tight may

cause implement to ride up on

wheels. This could result in injury

or equipment damage.

Do not carry passengers on

implement at any time.

For Your Protection

Thoroughly read and understand the “Safety Label” section, read all instructions noted on them.

Shutdown and Storage

Lower machine to ground, put tractor in park, turn off engine, and remove the key.

Detach and store implements in a area where children normally do not play. Secure implement by using blocks and supports.

OFF

11/14/08

AFM4211 All-Flex Mowers 315-507M

1

Image 3
Contents All-Flex Mowers Table of Contents Safety at All Times Use a Safety Chain Practice Safe MaintenanceTransport Machinery Safely Keep Riders Off Machinery Tire SafetyWear Protective Equipment Avoid High Pressure Fluids Hazard818-339C Safety Labels818-561C 818-019C818-130C 818-337C818-552C 818-556C 818-045C818-555C 818-543C 818-003C838-345C 838-270C818-230C 0818-187C 818-229C818-540C Using This Manual ApplicationOwner Assistance Tractor Hook-up Tractor RequirementsHardware Torque Information PTO To Drawbar Set-UpMain Driveline Installation Check Constant Velocity Driveline LengthDriveline Shortening Gauge Wheel Assembly Hydraulic Hook-upPull Rope Hook-up Transport Fold Hydraulic Plumbing Bleeding HydraulicsJoint Timing IntroductionJoint Timing TransportingPre-Operation Instructions Constant Velocity Driveline AngleOperating Instructions Table of Contents Cutting Height Chart Center Deck Height AdjustmentsBelt Tension Accessory Part Numbers Ball Swivel HitchCutting Blades Blade Inspection MaintenanceBlade Placement Servicing Mower BladesBlade Removal And Installation Blade RotationBlade Removal Blade Sharpening Belt InstallationBlade Sharpening Blade OptionsClutch Types Clutch Disassembly, Inspection & AssemblyDriveline Protection Type a Clutches Clutch Run-InPlate Assembly Step Plate Disassembly StepHex Head Socket Bolts Disassembly and AssemblyType B Clutch Assembly Type B Clutch Clutch Run-InTires With Air Pressure StorageDriveline Shafts LubricationHours Driveline Constant Velocity ShaftBlade Spindle Bearings, Center Deck Wheel Support BushingsWheel Bushings Gauge Wheels Wheel Bushings Transport HubsBlade Spindle Bearings, Wing Decks RequiredWay Gearbox Mower Deck GearboxWing Flex Pivot Lugs Transport LocksWing Deck Pivot Bushings Rear Deck Pivot Half ClampsAFM4211 All-Flex Grooming Mowers Specification / CapacityTable of Contents Features Benefits Problem Cause Solution Gearbox noisy Discharge openings pluggedBelt slipping Patches of uncut grassTorque Values Chart Tire Inflation ChartAdditional Torque Values 40 AFM4211 All-Flex Mowers 315-507M Overall Unit and Drivelines One year Parts and Labor WarrantyCorporate Office P.O. Box 5060 Salina, Kansas 67402-5060 USA
Related manuals
Manual 82 pages 29.47 Kb