Land Pride AFM4211 Transport Machinery Safely, Use a Safety Chain, Practice Safe Maintenance

Page 4

Table of Contents

Important Safety Information

Land Pride

These are common practices that may or may not be applicable to the products described in this manual.

Use Safety

Lights and Devices

Slow moving tractors, self- propelled equipment, and towed implements can create a hazard when driven on public roads. They are difficult to see, especially at night.

Flashing warning lights and turn signals are recommended whenever driving on public roads.

Transport

Machinery Safely

Comply with state and local laws.

Maximum transport speed for implement is 20 mph. DO NOT EXCEED. Never travel at a speed which does not allow adequate control of steering and stopping. Some rough terrains require a slower speed.

Sudden breaking can cause a towed load to swerve and upset. Reduce speed if towed load is not equipped with breaks.

Use the following maximum speed - tow load weight ratios as a guideline:

20 mph when weight is less than or equal to the weight of tractor.

10 mph when weight is double the weight of tractor.

IMPORTANT: Do not tow a load that is more than double the weight of tractor.

Use A Safety Chain

A safety chain will help control drawn machinery should it separate from the tractor drawbar.

Use a chain with the strength rating equal to or greater than the gross weight of the towed machinery.

Attach the chain to the tractor drawbar support or other specified anchor location. Allow only enough slack in the chain to permit turning.

Do not use safety chain for towing.

Practice Safe

Maintenance

Understand procedure before doing work. Use proper tools and equipment, refer to Operator’s Manual for additional information.

Work in a clean dry area.

Lower the implement to the ground, put tractor in park, turn off engine, and remove key before performing maintenance.

Allow implement to cool completely.

Do not grease or oil implement while it is in operation.

Inspect all parts. Make sure parts are in good condition & installed properly.

Remove buildup of grease, oil or debris.

Remove all tools and unused parts from implement before operation.

2

AFM4211 All-Flex Mowers 315-507M

11/14/08

Image 4
Contents All-Flex Mowers Table of Contents Safety at All Times Practice Safe Maintenance Use a Safety ChainTransport Machinery Safely Tire Safety Wear Protective EquipmentAvoid High Pressure Fluids Hazard Keep Riders Off MachinerySafety Labels 818-339C818-019C 818-561C818-337C 818-130C818-045C 818-552C 818-556C818-555C 818-003C 838-345C838-270C 818-543C0818-187C 818-229C 818-230C818-540C Application Using This ManualOwner Assistance Tractor Requirements Hardware Torque InformationPTO To Drawbar Set-Up Tractor Hook-upCheck Constant Velocity Driveline Length Main Driveline InstallationDriveline Shortening Hydraulic Hook-up Gauge Wheel AssemblyPull Rope Hook-up Bleeding Hydraulics Transport Fold Hydraulic PlumbingIntroduction Joint TimingTransporting Joint TimingConstant Velocity Driveline Angle Pre-Operation InstructionsOperating Instructions Table of Contents Center Deck Height Adjustments Cutting Height ChartBelt Tension Ball Swivel Hitch Accessory Part NumbersCutting Blades Maintenance Blade PlacementServicing Mower Blades Blade InspectionBlade Rotation Blade Removal And InstallationBlade Removal Belt Installation Blade SharpeningBlade Options Blade SharpeningClutch Disassembly, Inspection & Assembly Driveline ProtectionType a Clutches Clutch Run-In Clutch TypesPlate Disassembly Step Plate Assembly StepDisassembly and Assembly Type B Clutch AssemblyType B Clutch Clutch Run-In Hex Head Socket BoltsStorage Tires With Air PressureLubrication HoursDriveline Constant Velocity Shaft Driveline ShaftsWheel Support Bushings Wheel Bushings Gauge WheelsWheel Bushings Transport Hubs Blade Spindle Bearings, Center DeckRequired Way GearboxMower Deck Gearbox Blade Spindle Bearings, Wing DecksTransport Locks Wing Deck Pivot BushingsRear Deck Pivot Half Clamps Wing Flex Pivot LugsSpecification / Capacity AFM4211 All-Flex Grooming MowersTable of Contents Features Benefits Problem Cause Solution Discharge openings plugged Belt slippingPatches of uncut grass Gearbox noisyTire Inflation Chart Torque Values ChartAdditional Torque Values 40 AFM4211 All-Flex Mowers 315-507M Warranty Overall Unit and Drivelines One year Parts and LaborCorporate Office P.O. Box 5060 Salina, Kansas 67402-5060 USA
Related manuals
Manual 82 pages 29.47 Kb