Land Pride AFM4211 Type B Clutch Clutch Run-In, Disassembly and Assembly, Hex Head Socket Bolts

Page 30

Table of Contents

Section 5: Maintenance and Lubrication

Land Pride

Type B Clutch

Clutch Run-In

Refer to Figure 5-10:

1.Loosen counterclockwise all 8 hex head socket bolts uniformly 6 full turns.

2.Cycle clutch on and off 5 or 6 times (15 seconds on and 15 seconds off) with the engine operating at half throttle. Disengage driveline, shut off tractor and remove key. Wait for all components to stop before dismounting from tractor.

3.Tighten hex head socket bolts fully back. Clutch is ready for use

4.The clutch should be checked during the first hour of cutting and periodically each week.

Hex Head

Socket Bolts

21270

Type B Clutch Run-In

Figure 5-10

Disassembly and Assembly

Refer to Figure 5-11:

If the clutch run-in procedure indicated that one or more of the friction disks did not slip, then the clutch must be disassembled to separate the friction disks.

1.Rotate 8 hex head socket bolts (#2) all the way out to free stop flange (#3).

2.Rotate stop flange (#3) and remove from housing (#11)

3.Remove the following inner components:

a.Spring kit (#4)

b.Pressure flange (#5)

c.1st Friction Disc (#6)

d.Hub with flange and pull collar (#7 & #1)

e.2nd Friction disc (#6)

f.Intermediate flange (#8)

g.3rd Friction disc (#6)

h.Hub disc (#9)

i.4th Friction disc (#6)

j.Bearing (#10)

4.Inspect all components and replace to their original position. Make certain stop flange (#3) is replaced with its flanges down as shown.

(IMPORTANT NOTICE) Check position of lip on stop flange (UP or DOWN). Replace stop flange with lip in its original position.

22376

Type B Clutch Assembly

Figure 5-11

5. Fully tighten all 8 hex head socket bolts (#2).

28 AFM4211 All-Flex Mowers 315-507M

11/14/08

Image 30
Contents All-Flex Mowers Table of Contents Safety at All Times Use a Safety Chain Practice Safe MaintenanceTransport Machinery Safely Avoid High Pressure Fluids Hazard Tire SafetyWear Protective Equipment Keep Riders Off MachinerySafety Labels 818-339C818-019C 818-561C818-337C 818-130C818-552C 818-556C 818-045C818-555C 838-270C 818-003C838-345C 818-543C0818-187C 818-229C 818-230C818-540C Using This Manual ApplicationOwner Assistance PTO To Drawbar Set-Up Tractor RequirementsHardware Torque Information Tractor Hook-upMain Driveline Installation Check Constant Velocity Driveline LengthDriveline Shortening Gauge Wheel Assembly Hydraulic Hook-upPull Rope Hook-up Bleeding Hydraulics Transport Fold Hydraulic PlumbingTransporting IntroductionJoint Timing Joint TimingConstant Velocity Driveline Angle Pre-Operation InstructionsOperating Instructions Table of Contents Center Deck Height Adjustments Cutting Height ChartBelt Tension Accessory Part Numbers Ball Swivel HitchCutting Blades Servicing Mower Blades MaintenanceBlade Placement Blade InspectionBlade Removal And Installation Blade RotationBlade Removal Blade Options Belt InstallationBlade Sharpening Blade SharpeningType a Clutches Clutch Run-In Clutch Disassembly, Inspection & AssemblyDriveline Protection Clutch TypesPlate Disassembly Step Plate Assembly StepType B Clutch Clutch Run-In Disassembly and AssemblyType B Clutch Assembly Hex Head Socket BoltsStorage Tires With Air PressureDriveline Constant Velocity Shaft LubricationHours Driveline ShaftsWheel Bushings Transport Hubs Wheel Support BushingsWheel Bushings Gauge Wheels Blade Spindle Bearings, Center DeckMower Deck Gearbox RequiredWay Gearbox Blade Spindle Bearings, Wing DecksRear Deck Pivot Half Clamps Transport LocksWing Deck Pivot Bushings Wing Flex Pivot LugsSpecification / Capacity AFM4211 All-Flex Grooming MowersTable of Contents Features Benefits Problem Cause Solution Patches of uncut grass Discharge openings pluggedBelt slipping Gearbox noisyTorque Values Chart Tire Inflation ChartAdditional Torque Values 40 AFM4211 All-Flex Mowers 315-507M Warranty Overall Unit and Drivelines One year Parts and LaborCorporate Office P.O. Box 5060 Salina, Kansas 67402-5060 USA
Related manuals
Manual 82 pages 29.47 Kb