Land Pride AFM4211 manual Blade Removal And Installation, Blade Rotation

Page 26

Table of Contents

Section 5: Maintenance and Lubrication

Blade Removal And Installation

! CAUTION!

Depending on blade rotation, bolts attaching mower blades to their respective spindles may be either left hand or right hand. Prevent spindle and/or bolt damage by knowing which hand the threads are before removing and/or tightening any blade mounting bolts.

Refer to Figure 5-2

1. Verify blade rotation and bolt thread type (right hand or left hand) before loosening center blade bolts and removing blades to be sharpened or replaced.

NOTE: Blade bolt on the left hand deck is right hand threads. Blade bolts on the right hand and center decks are left hand threads.

Refer to Figure 5-3:

2. Remove blades by grasping the blade end (#1) with a rag or thick padded glove while loosening the blade mounting bolt (#4).

3. Remove blade bolt (#4) and Washer (#5) from blade being replaced.

Land Pride

IMPORTANT: Replace blades with Land Pride blades only.

IMPORTANT: Always install blades with cutting edge facing direction of blade spindle rotation and with wing tips pointing up towards bottom of deck.

4.Reinstall blade (#1), blade washer (#5) and bolt (#4). Care should be taken when installing the blade bolt to not get it cross threaded and to know if the bolt is right hand or left hand. Do not exceed 55 ft.-lbs. of torque on bolt.

Blade Rotation

Figure 5-2

22374

Blade Removal

Figure 5-3

24 AFM4211 All-Flex Mowers 315-507M

11/14/08

Image 26

Contents All-Flex Mowers Table of Contents Safety at All Times Transport Machinery Safely Use a Safety ChainPractice Safe Maintenance Avoid High Pressure Fluids Hazard Tire SafetyWear Protective Equipment Keep Riders Off MachinerySafety Labels 818-339C818-019C 818-561C818-337C 818-130C818-555C 818-552C 818-556C818-045C 838-270C 818-003C838-345C 818-543C0818-187C 818-229C 818-230C818-540C Owner Assistance Using This ManualApplication PTO To Drawbar Set-Up Tractor RequirementsHardware Torque Information Tractor Hook-upDriveline Shortening Main Driveline InstallationCheck Constant Velocity Driveline Length Pull Rope Hook-up Gauge Wheel AssemblyHydraulic Hook-up Bleeding Hydraulics Transport Fold Hydraulic PlumbingTransporting IntroductionJoint Timing Joint TimingConstant Velocity Driveline Angle Pre-Operation InstructionsOperating Instructions Table of Contents Center Deck Height Adjustments Cutting Height ChartBelt Tension Cutting Blades Accessory Part NumbersBall Swivel Hitch Servicing Mower Blades MaintenanceBlade Placement Blade InspectionBlade Removal Blade Removal And InstallationBlade Rotation Blade Options Belt InstallationBlade Sharpening Blade SharpeningType a Clutches Clutch Run-In Clutch Disassembly, Inspection & AssemblyDriveline Protection Clutch TypesPlate Disassembly Step Plate Assembly StepType B Clutch Clutch Run-In Disassembly and AssemblyType B Clutch Assembly Hex Head Socket BoltsStorage Tires With Air PressureDriveline Constant Velocity Shaft LubricationHours Driveline ShaftsWheel Bushings Transport Hubs Wheel Support BushingsWheel Bushings Gauge Wheels Blade Spindle Bearings, Center DeckMower Deck Gearbox RequiredWay Gearbox Blade Spindle Bearings, Wing DecksRear Deck Pivot Half Clamps Transport LocksWing Deck Pivot Bushings Wing Flex Pivot LugsSpecification / Capacity AFM4211 All-Flex Grooming MowersTable of Contents Features Benefits Problem Cause Solution Patches of uncut grass Discharge openings pluggedBelt slipping Gearbox noisyAdditional Torque Values Torque Values ChartTire Inflation Chart 40 AFM4211 All-Flex Mowers 315-507M Warranty Overall Unit and Drivelines One year Parts and LaborCorporate Ofﬁce P.O. Box 5060 Salina, Kansas 67402-5060 USA

Related manuals

Manual 82 pages 29.47 Kb