Kenmore 7, 11, 5, 3, 9 manual Reel to BED Knife Adjustment, Pre-single point adjustment units

Page 27

REEL TO BED KNIFE ADJUSTMENT

Pre-single point adjustment units.

Fig.19

When the reels are sharp, and correctly adjusted to the bed-knife, they will cut paper as clean as scissors.

To adjust the reel blade to bed-knife clearance :

Check the Bed-knife and the Bed-knife Holder Screws for tightness.

Compress the Telescopic Arm with the belt release tool, to allow the Reel to be rotated.

CAUTION

The Telescopic Arm is heavily ‘spring loaded’. Exercise care when compressing it to avoid personal injury.

Fig.20

Turn the reel manually. If the reel blades contact the Bed-knife, turn the Reel Adjusters CCW until there is no contact.

Back-off the lock-slug screw and turn each reel adjuster CW, in small amounts, until the reel blades ‘just’ contact the bed-knife.

Adjust the reels to give an even cut across the full length of the bed-knife.

Tighten the lock-slug screw.

Fig.19

Fig.20

24

Image 27
Contents Kesmac Foreword Kesmac Transportable Reel MowersLift Cain Adjustment Eleven Gang Mowing Procedure Contents Safety Precautions Vertical Mower General SafetyMaintenance Specifications HOOK-UP to TractorIf you do not understand……….ASK Before Operating the Mower Safety Precautions General SafetyMaintenance Safety Be a Qualified Operator bySafety Alert Symbol During MaintenanceDECALS. See Pages 5 & 6 also Page Page Operating Conditions Turf tires are not designed for use on highways Mainwheel BearingsTires Main and OutriggerDaily Inspection Daily Inspection Drive Belts and Sheaves Primary BeltsReel Drive Belts Tongue Tube Daily Inspection PTO ShaftTo do so may result in serious personal injury This check should be done at regular service intervalsDaily Inspection Hydraulic System Guards and DecalsMower Transport Wheel Bearing Service Life Lifting the Reels Transport Safety ChainsTransport Lowering the Reels Do not set the tractor engine RPM too highREEL/WING Lower Sequence Hydraulic Lift Operation REEL/WING Lift SequenceHydraulic Lift Operation REEL/WING Lift Sequence Sequence Valve Setting , 9 & 11 Gang only Relief Valve Setting Reels 4 Lift Chain AdjustmentsReels 4 and 5 Lift Chains AdjustmentCutting Height Adjusment Cutting Height Adjustment FAIRWAY. Floating Head Pre-single point adjustment units Reel to BED Knife AdjustmentReel to BED-KNIFE Single Point Adjustment Drive Belt Adjustment Vertical MOWER. Depth of CUT AdjustmentVertical Mower Operation Routine Maintenance Hours or WeeklyHours Annual Maintenance Inspection Lubrication = Grease. B = OilGearbox Lubrication Gearbox Lubrication Cones as assemblies Main Wheel Axle Assembly . From Feb.07Main Wheel Axle Assembly. Serial No’s 357 to February Single Outrigger Wheel Dual Outrigger Wheels Outrigger Single Wheel. From Serial NoWing Kick Springs Main Drive Belts Reel Drive Belts Maintenance Maintenance Main Jackshaft Bearing replacement PTO Shaft SET- UPShafts must be set-up as illustrated Gang Gang 7-Gang 5-Gang Gang 9-Gang SpecificationsNumber of Reels Specifications Primary DriveTractor POWER. Nominal STEP-UP Drive RatioHydraulic Operation Backlapping AttachmentBacklapping Operation Reel and Bedknife Sharpening Optional Castor Wheel Gang only Wing FrameLift Chains Attachment Points Torque Guide Grade 5 and 8 Fasteners. Coarse ThreadSize Plated Plain
Related manuals
Manual 44 pages 60.15 Kb