Kenmore 7, 11, 5, 3, 9 manual Maintenance

Page 42

MAINTENANCE

Reel Drive Belts

To replace the Reel Drive Belts. Reels 2 and 3.

Fig.34

Remove the Safety Chain from the Stay Rod and compress the Telescopic Arm with the Compression Tool as shown in Fig.33.

Remove the Front Jackshaft Couplers and pull the belt through the gap between the Jackshafts.

Install the new belt onto the sheaves. Fit the Jackshaft Coupler.

Carefully release the Compression Tool and re- attach the Safety Chain.

To replace the Reel Drive Belts. Reels 6 and 7.

Fig.35

With the Wings ‘down’, remove Shaft Cover.

Remove the Socket Set Screws from the ‘outboard’ end of inner front PTO Shafts, and slide the PTO Shafts off the Reel Drive Shaft.

Remove the Safety Chain from the Stay Rod and compress the Telescopic Arm as in Fig.33.

Remove Belts. Fit new Belts. Carefully release the Compression Tool and attach Safety Chain. Refit PTO Shafts and Covers.

39

Fig.34

Fig.35

IMPORTANT

Apply ‘Loctite 242’ to the PTO Shaft Setscrews.

Image 42
Contents Kesmac Kesmac Transportable Reel Mowers ForewordSpecifications HOOK-UP to Tractor Contents Safety Precautions Vertical Mower General SafetyMaintenance Lift Cain Adjustment Eleven Gang Mowing ProcedureIf you do not understand……….ASK Be a Qualified Operator by Safety Precautions General SafetyMaintenance Safety Before Operating the MowerDuring Maintenance Safety Alert SymbolDECALS. See Pages 5 & 6 also Page Page Operating Conditions Main and Outrigger Mainwheel BearingsTires Turf tires are not designed for use on highwaysDaily Inspection Daily Inspection Drive Belts and Sheaves Primary BeltsReel Drive Belts Daily Inspection PTO Shaft Tongue TubeGuards and Decals This check should be done at regular service intervalsDaily Inspection Hydraulic System To do so may result in serious personal injuryMower Transport Wheel Bearing Service Life Do not set the tractor engine RPM too high Transport Safety ChainsTransport Lowering the Reels Lifting the ReelsHydraulic Lift Operation REEL/WING Lift Sequence REEL/WING Lower SequenceHydraulic Lift Operation REEL/WING Lift Sequence Sequence Valve Setting , 9 & 11 Gang only Relief Valve Setting Lift Chain Adjustments Reels 4Lift Chains Adjustment Reels 4 and 5Cutting Height Adjusment Cutting Height Adjustment FAIRWAY. Floating Head Reel to BED Knife Adjustment Pre-single point adjustment unitsReel to BED-KNIFE Single Point Adjustment Vertical MOWER. Depth of CUT Adjustment Drive Belt AdjustmentVertical Mower Operation Routine Maintenance Hours or WeeklyHours Annual Maintenance Inspection = Grease. B = Oil LubricationGearbox Lubrication Gearbox Lubrication Main Wheel Axle Assembly . From Feb.07 Cones as assembliesMain Wheel Axle Assembly. Serial No’s 357 to February Outrigger Single Wheel. From Serial No Single Outrigger Wheel Dual Outrigger WheelsWing Kick Springs Main Drive Belts Reel Drive Belts Maintenance Maintenance Main Jackshaft Bearing replacement PTO Shaft SET- UPShafts must be set-up as illustrated Specifications Gang Gang 7-Gang 5-Gang Gang 9-GangSTEP-UP Drive Ratio Specifications Primary DriveTractor POWER. Nominal Number of ReelsBacklapping Attachment Hydraulic OperationBacklapping Operation Reel and Bedknife Sharpening Wing Frame Optional Castor Wheel Gang onlyLift Chains Attachment Points Torque Guide Grade 5 and 8 Fasteners. Coarse ThreadSize Plated Plain
Related manuals
Manual 44 pages 60.15 Kb