Kenmore 5, 11, 7, 3, 9 manual Reel Drive Belts

Page 41

MAINTENANCE

Reel Drive Belts.

When fitting Belts to Reels 2 or 3, the Main Drive Belts and the Jackshaft Couplers, must be removed first. See page 37. To keep the Compression Tool clear of the Stay Rod the Binder Collar and Chain may be used.

CAUTION

When the Binder Collar is used check it is firmly in place on the ¾ nut, before compressing the Telescopic Arm.

To replace the Reel Drive Belts. Reels 1, 4 and 5. :

Fig.33

•Remove the Safety Chain at the Stay Rod. Attach the Release Tool. Compress the Telescopic Arm.

•Remove Tie Rod from the Reel.

•Carefully release the Compression Tool to fully expand the Telescopic Arm.

•Pull the Reel ‘out’, to separate the Telescopic Arm, and remove the belt.

•Install new Drive Belt and re-assemble in the reverse order.

CAUTION Telescopic Arms are heavily spring loaded.

Exercise extreme care when compressing them to avoid serious injury.

Fig.33

38

Page 40 Page 42
Image 41
Page 40 Page 42
Contents Kesmac Foreword Kesmac Transportable Reel MowersMaintenance Contents Safety Precautions Vertical Mower General SafetySpecifications HOOK-UP to Tractor Lift Cain Adjustment Eleven Gang Mowing ProcedureIf you do not understand……….ASK Maintenance Safety Safety Precautions General SafetyBe a Qualified Operator by Before Operating the MowerSafety Alert Symbol During MaintenanceDECALS. See Pages 5 & 6 also Page Page Operating Conditions Tires Mainwheel BearingsMain and Outrigger Turf tires are not designed for use on highwaysDaily Inspection Reel Drive Belts Daily Inspection Drive Belts and SheavesPrimary Belts Tongue Tube Daily Inspection PTO ShaftDaily Inspection Hydraulic System This check should be done at regular service intervalsGuards and Decals To do so may result in serious personal injuryMower Transport Wheel Bearing Service Life Transport Lowering the Reels Transport Safety ChainsDo not set the tractor engine RPM too high Lifting the ReelsREEL/WING Lower Sequence Hydraulic Lift Operation REEL/WING Lift SequenceHydraulic Lift Operation REEL/WING Lift Sequence Sequence Valve Setting , 9 & 11 Gang only Relief Valve Setting Reels 4 Lift Chain AdjustmentsReels 4 and 5 Lift Chains AdjustmentCutting Height Adjusment Cutting Height Adjustment FAIRWAY. Floating Head Pre-single point adjustment units Reel to BED Knife AdjustmentReel to BED-KNIFE Single Point Adjustment Drive Belt Adjustment Vertical MOWER. Depth of CUT AdjustmentVertical Mower Operation Hours Routine MaintenanceHours or Weekly Annual Maintenance Inspection Lubrication = Grease. B = OilGearbox Lubrication Gearbox Lubrication Cones as assemblies Main Wheel Axle Assembly . From Feb.07Main Wheel Axle Assembly. Serial No’s 357 to February Single Outrigger Wheel Dual Outrigger Wheels Outrigger Single Wheel. From Serial NoWing Kick Springs Main Drive Belts Reel Drive Belts Maintenance Maintenance Shafts must be set-up as illustrated Main Jackshaft Bearing replacementPTO Shaft SET- UP Gang Gang 7-Gang 5-Gang Gang 9-Gang SpecificationsTractor POWER. Nominal Specifications Primary DriveSTEP-UP Drive Ratio Number of ReelsHydraulic Operation Backlapping AttachmentBacklapping Operation Reel and Bedknife Sharpening Optional Castor Wheel Gang only Wing FrameLift Chains Attachment Points Size Plated Plain Torque GuideGrade 5 and 8 Fasteners. Coarse Thread
Related manuals
Manual 44 pages 60.15 Kb
Top Page Image Contents