Marantz Essential Setup and Operation Guide for SR5001 Stereo Receiver

Page 19

BASIC OPERATION

NORMAL MODE

Importants:

• Some codes may be not match your equipment.

In this case, you can use LEARN mode to store these

2. Press and hold down the SOURCE button for appliance which should be controlled and press SET button until the SEND indicator blinking

RESETTING THE CODE

ENGLISH

(When operating Marantz AV equipment products) This remote control is preset with a total of 12 types of remote codes, including Marantz TV (television), DVD, VCR (VCR deck), DSS (satellite broadcasting tuner), TUNER, CD, CD-R, MD, TAPE (tape deck), AUX1, AUX2, and AMP (amplifier).

Learning is not necessary for Marantz products. You can use these products without setting any codes.

codes.

• The preset codes do not cover full functions.

If you need extra function, use LEARN mode to

store extra function.

• Wen the batteries are getting weak, the preset

procedure is not successful.

PROGRAMMING WITH THE 4-DIGIT CODE

twice. Then back light flushes.

3. Aim the remote control at the appliance and slowly alternate between pressing CH+ button and the SOURCE ON/OFF button for the appliance.

4. Stop when the appliance turns off.

5. Press ENTER button once to lock in the code.

1.

1.

 

LEARN

SEND

 

SOURCE

SET

OFF

ON

l/

 

 

 

SLEEP

DISPLAY

P.DIRECT

SURROUND

 

 

 

LIP SYNC/

AUTO

 

dts

INPUT

1

2

3

 

DISC+

ANGLE

SUB TITLE

AUDIO

CH-SEL V-OFF

ATT.

 

BASS

TREBLE

TV

DVD

VCR

DSS

TUNER

CD

CDR

MD

TAPE

AUX1

AUX2

AMP

2.

LEARNSEND

SOURCE

SET

OFF

ON

l/

 

 

 

SLEEP

DISPLAY

P.DIRECT

SURROUND

 

 

 

LIP SYNC/

AUTO

 

dts

INPUT

1

2

3

 

CS

EX/ES

VIRTUAL

T.MODE

4

5

6

 

M-CH ST

STEREO

NIGHT

P.SCAN

7

8

9

 

 

7.1CH IN

A/D

HT-EQ

CL

0

+10

MEMO

CH/ CAT

SPKR A/B

MUTE

VOLUME

 

 

 

MULTI/ CAT

M-SPKR

 

1. Press the SOURCE button. For this example, press DVD.

- PRESET +

- TUNING +

DISC+

ANGLE

SUB TITLE AUDIO

CH-SEL

V-OFF

ATT.

1.

SOURCE

SET

OFF

ON

l/

 

 

 

SLEEP

DISPLAY

P.DIRECT

SURROUND

 

 

 

LIP SYNC/

AUTO

 

dts

INPUT

CHECKING THE CODE

REMOTE CONTROLLER

RC5001SR

INFO

MENU

Pressing the SOURCE button once changes the remote control to the settings for the source that was pressed.

To change the amplifier on other source, press the SOURCE button twice (double-click). The code is sent, and then the amplifi er source

1.

BASSTREBLE

TV DVD VCR DSS

TUNER CD CDR MD

TAPE AUX1 AUX2 AMP

REMOTE CONTROLLER

RC5001SR

2.

1

2

3

 

CS

EX/ES

VIRTUAL

T.MODE

4

5

6

 

M-CH ST

STEREO

NIGHT

P.SCAN

7

8

9

 

 

7.1CH IN

A/D

HT-EQ

CL

0

+10

MEMO

CH/ CAT

SPKR A/B

MUTE

VOLUME

 

 

1.

 

LEARN

SEND

 

SOURCE

SET

OFF

ON

l/

 

 

 

SLEEP

DISPLAY

P.DIRECT

SURROUND

 

 

 

LIP SYNC/

AUTO

 

dts

INPUT

1

2

3

 

3.

4.

SOURCE SET OFF ON l/

SLEEP DISPLAY P.DIRECT SURROUND

 

 

 

LIP SYNC/

AUTO

 

dts

INPUT

1

2

3

 

CS

EX/ES

VIRTUAL

T.MODE

4

5

6

 

M-CH ST

STEREO

NIGHT

P.SCAN

7

8

9

 

 

7.1CH IN

A/D

HT-EQ

CL

0

+10

MEMO

1. Press and hold down the SOURCE button for appliance which should be controlled and press SET button until the SEND indicator blinking twice.

Then back light flushes.

2. Press the below codes to reset.

changes to DVD.

SETTING THE BACK LIGHT

Each time press the buttons, illuminate button 2 seconds.

1. Press and hold down the SOURCE button for the appliance which should be controlled and press SET button until the SEND indicator blinks twice. Then back light flushes.

2. Press the 4-digit code for appliance (code table at the end of this book)

1.

DISC+

ANGLE

SUB TITLE

AUDIO

CH-SEL V-OFF

ATT.

 

 

BASS

TREBLE

TV

DVD

VCR

DSS

TUNER

CD

CDR

MD

TAPE

AUX1

AUX2

AMP

REMOTE CONTROLLER

RC5001SR

2.

CH/ CAT

VOLUME

SPKR A/B

MUTE

MULTI/ CAT

M-SPKR

INFO

MENU

ENTER

T.TONE

 

/SET UP

EXIT

TV : 1000

DVD : 2000

VCR : 3000

DSS : 4000

The indicator will blink twice.

To turn off back light, press and hold down the SET and OFF button until SEND indicator blinks twice. To turn on it again, press and hold down the SET and ON button until SEND indicator blinks twice.

Initial is back light ON.

PRESET MODE

(When operating non-Marantz AV equipment products)

When the procedure is successful, the SEND indicator will blink twice.

Note:

If the indicator did not blink twice, then repeat steps 1 through 2 and try entering the same code again.

SCANNING THE CODE TABLE

1. Press and hold down the SOURCE button for appliance which should be controlled and press SET button until the SEND indicator blinking twice then back light flushes.

2. Press the INFO button.

The SEND indicator will blink twice.

3. To view the code for first digit, press 1 once.

Wait 3 seconds, count the SEND indicator

Note:

After this procedure, the selected SOURCE button is set initial code.

This remote control is preset with remote control codes from AV equipment by other manufacturers. The preset codes are TV, VCR, DVD and DSS. Settings can be made in one of two ways.

When the preset codes are set, the following codes are contained in the source button of the remote control.

See the attached manufacturer number list for the preset manufacturers, devices, preset numbers, and other settings.

Remote control

Corresponding preset Device name

source name

code

 

TV

TV

Television

2.

2.

 

LEARN

SEND

 

SOURCE

SET

OFF

ON

l/

 

 

 

SLEEP

DISPLAY

P.DIRECT

SURROUND

 

 

 

LIP SYNC/

AUTO

 

dts

INPUT

1

2

3

 

CS

EX/ES

VIRTUAL

T.MODE

4

5

6

 

DISC+

ANGLE

SUB TITLE

AUDIO

CH-SEL V-OFF

ATT.

 

BASS

TREBLE

TV

DVD

VCR

DSS

TUNER

CD

CDR

MD

TAPE

AUX1

AUX2

AMP

REMOTE CONTROLLER

RC5001SR

3.

3.

5.

SOURCE SET OFF ON

l/

 

 

 

SLEEP

DISPLAY

P.DIRECT

SURROUND

 

 

 

LIP SYNC/

AUTO

 

dts

INPUT

1

2

3

 

CS

EX/ES

VIRTUAL

T.MODE

4

5

6

 

M-CH ST

STEREO

NIGHT

P.SCAN

7

8

9

 

 

7.1CH IN

A/D

HT-EQ

CL

0

+10

MEMO

CH/ CAT

SPKR A/B

MUTE

VOLUME

 

 

 

MULTI/ CAT

M-SPKR

 

INFO

MENU

 

ENTER

T.TONE

 

/SET UP

EXIT

blinks (e.g. 3 blinks = 3) and write down the number.

Note:

If a code digit is “0”, the SEND indicator will not blink.

4. Repeat step 3 three more times for remaining

digits. Use 2 for the second digit, 3 for the third digit, and 4 for the fourth digit.

DVD

DVD

DVD player

VCR

VCR

Video deck

DSS

SATELLITE

Satellite broadcasting

 

 

tuner equipment

1. Switch on the appliance which should be controlled.

15

Image 19
Contents Model SR4001/SR5001 User Guide Nederlands EnglishFrançais DeutschDeutsch EnglishMains FrançaisSvenska NederlandsEspañol ItalianoRecycling Table of Contents Foreword IntroductionNeo6 offers several important improvements as follow DescriptionAbout Dolby Pro Logic User Guide FeaturesAccessories Remote Controller RC5001SRFront Panel ATT Attenuate button Volume control knobMode button @2 Headphone jack for stereo headphones¡6 Encoded Channel Status indicators ¡4 Analog input indicator¡5 Signal Format indicators Disp Display Off indicator Video-OFF mode indicatorTV, DVD, VCR1, DSS/VCR2 Rear Panel8FLASHER 4AUDIO IN/OUT CD, TAPE, CD-R TV, DVD, VCR1, DSS/VCR25DIGITAL Input 6HDMI INPUT/OUTPUTFunction and Operation Remote Control Operation¤3 P.SCAN button ¤4 MEMO/HT-EQ button ¤6 Volume +/- buttons¤1 BAND/LIP SYNC/INPUT button ¤2 T.MODE buttonSR4001/SR5001 Remote control unit RC5001SR Operation of Remote Control UnitLoading Batteries Tuner Mode AMP ModeGeneral Information of RC5001SR to SR4001/SR5001 Controlling Marantz Components Controlling a Marantz DVD Player DVD ModeControlling a Marantz CD CD Mode Controlling a Marantz VCR VCR ModeRewind / Forward Searchs forward or backward Controlling a Marantz Tape Deck Tape ModeBasic Operation Learning Procedure Learn ModeErasing Programmed Codes Returning to Initial Settings Height of the Speaker Units Connecting Speakers Speaker PlacementConnecting Speaker Wire ConnectionsConnecting a Subwoofer Connecting Audio ComponentsConnecting Digital Audio Components Component jack Connecting Video ComponentsVIDEO, S-VIDEO , Component Jacks Video jackConnecting AN External Power Amplifier Advanced ConnectingConnecting the Remote Control Jacks Connecting Multi Channel Audio SourceConnecting AN AM Outdoor Antenna Connecting the Antenna TerminalsConnecting the Supplied Antennas Connecting AN FM Outdoor AntennaMultiroom Bi-wire ConnectionHdmi Jack Connecting Hdmi DevicesSelect an input source from the OSD menu system. See On Screen Display Menu System SetupSpeakers Size Speaker SetupSpeakers Distance PreferenceCS II Circle Surround II Parameter SurroundCH Input Level Multi Room SR5001 onlyRelation of the speakers number and conectted speaker Simple SetupRelation of the room size and floor space SR4001/SR5001 Basic OperationVideo Convert SR5001 onlyNight Mode Selecting the Surround ModeAdjusting the Main Volume Using the Sleep TimerSurround Mode Source Direct CSII-Mono modeVirtual StereoRelation between the selected surround Mode and the input signalOther Function Listening Through HeadphonesDolby Headphone Mode Display ModeCH Input Selecting Analog Audio Input or Digital Audio InputRecording AN Analog Source HT-EQLIP.SYNC SR5001 only AUX2 InputListening to the Tuner Preset Memory RDS Operation Room OUT Terminals Multi Room Playback Using the Multi Speaker TerminalsMulti Room Playback Using the Multi Multi RoomVolume of S. Speaker B is interlocked with the main volume Another Room Playback Using Surround Speaker B TerminalsSymptom Cause Remedy TroubleshootingDimensions Technical Specifications1083, 1090, 1100 1110, 1113, 1133, 11361010, 1069, 1073, 1111 1094, 1139, 1140, 11453040, 3048, 3067, 3072 3056, 3068, 30693026, 3029, 3032 3052, 3060, 30674002, 4008, 4009 Is a registered trademark