Other Function, TV Auto ON/OFF Function

When the station is received, the SR4001/ SR5001 turns ON and TV is selected automatically.

OTHER FUNCTION

TV AUTO ON/OFF FUNCTION

This function allows the component connected to the TV-VIDEO in jack to control the power (ON/OFF) to the SR4001/SR5001.

AUTO POWER ON

1. Be sure the TV auto mode is ENABLED. (Refer page 26 : System Setup)

2. Connect your TV TUNER (etc) to the TV- VIDEO in terminal. Be sure to connect the VIDEO input.

3. Turn OFF the power to the TV TUNER and the SR4001/SR5001.

4. Turn ON the TV TUNER and tune in a receivable station.

AUTO POWER OFF

1. In the above situation, turn the TV TUNER OFF or select a channel that does not contain any broadcast.

2. The power to the SR4001/SR5001 switches to STANDBY after approx. 5 minutes.

Notes:

•AUTO POWER OFF is canceled if the SR4001/ SR5001 is set to a source other than TV.

The function reactivates when TV is selected again.

•Some TV broadcasts may cause the TV AUTO FUNCTION to turn ON.

•The S-Video terminal does not support “TV AUTO ON/OFF” function.

ATTENUATION TO ANALOG INPUT SIGNAL

REC	T.DISP	PTY	F.DIRECT
- PRESET +		- TUNING +
DISC+	ANGLE	SUB TITLE	AUDIO
CH-SEL V-OFF		ATT.
	BASS	TREBLE
TV	DVD	VCR	DSS
TUNER	CD	CDR	MD

If the selected analog audio input signal is greater than the capable level of internal processing, the “PEAK” indicator will light up on the front display. If this happens, you should press the ATT button on the remote.

“ATT” indicator will be illuminated when this function is activated. The signal-input level is reduced by about half. Attenuation will not work with the output signal of TAPE-OUT, CD-R/MD-OUT, VCR1-OUT and DSS/VCR2-OUT.

This function is memorized for each individual input source.

LISTENING THROUGH HEADPHONES

This jack may be used to listen to the SR4001/ SR5001’s output through a pair of headphones. Be certain that the headphones have a standard 1/4” stereo phono plug. (Note that the speakers will automatically be turned off when the headphone jack is in use.)

AV SURROUND RECEIVER SR5001

Note:

The surround mode returns to the previous setting as soon as the plug is removed from the jack.

DOLBY HEADPHONE MODE

This feature simulates the waveforms of the actual sounds heard from the speakers.

When headphones are used, the MENU button automatically switches to the Dolby headphone mode.

The OSD that appears when the MENU button is pressed is shown below.

	HEAD PHONE
DOLBY HP MODE : ON
SURROUND		: OFF
L	LEVEL	:	0	dB
R	LEVEL	:	0	dB

DOLDBY HP (Headphone) MODE can be selected with the left and right cursor buttons.

BYPASS → ON → BYPASS

BYPASS: Bypasses the Dolby headphone mode and delivers ordinary 2-channel stereo.

ON: Dolby headphone mode active.

When the PURE DIRECT mode is selected, Dolby surround processing is bypassed and “✽✽✽” is displayed as the mode indication.

The surround mode can be selected when mode is ON.

L/R LEVEL can be set in the ±10 dB range.

Notes:

•The surround mode returns to the previous setting as soon as the plug is removed from the jack.

•TONE cannot be set when mode is ON.

•The Dolby Headphone function will not work when 32 or 96 kHz PCM digital signals are input.

VIDEO ON/OFF				ENGLISH
When no video signal is connected to the SR4001/				ENGLISH
When no video signal is connected to the SR4001/
SR5001 or a DVD, etc., is connected directly to your
TV, the unnecessary video circuit can be turned off
by selecting the “VIDEO OFF” setting.
To select video off, press the AMP button and press
the V-OFFbutton.
TV	DVD	VCR	DSS
TUNER	CD	CDR	MD
R5001
TAPE	AUX1	AUX2	AMP
	REMOTE CONTROLLER
	RC5001SR
REC	T.DISP	PTY F.DIRECT
- PRESET +		- TUNING +
DISC+	ANGLE	SUB TITLE	AUDIO
CH-SEL V-OFF		ATT.
	BASS	TREBLE
TV	DVD	VCR	DSS

DISPLAY MODE

ER SR5001

	LEARN	SEND
SOURCE	SET	OFF	ON
l/
SLEEP	DISPLAY	P.DIRECT	SURROUND
			LIP SYNC/
AUTO		dts	INPUT
1	2	3
CS	EX/ES	VIRTUAL	T.MODE
4	5	6
M-CH ST	STEREO	NIGHT	P.SCAN
7	8	9

You can select the display mode for the front display of the SR4001/SR5001.

To select this mode, press the DISPLAY on the remote control.

When this button is pressed, the display mode is switched in the following sequence.

→Surround Mode → Auto-display Off → Display Off

→Input Function → Surround Mode....

In Auto display off mode, the display is off. But, if you make a change to the unit such as input or surround mode, the display will show that change, then go back to off after about 3 seconds. When changing the volume, it is not displayed.

In Display off mode, the display is off completely.