Marantz SR4001 and SR5001 User Manual - HDMI Connection and Setup Guide

HDMI JACK

This unit has two HDMI inputs and one HDMI output. It can send digital video and audio signals from DVDs and other sources directly to a display. It minimizes signal degradation caused by analog conversion so that high quality images can be enjoyed.

Select an input source from the OSD menu system. (See page 25)

Notes:

•When the HDMI output is connected to a display monitor that does not support HDCP, signals are not output. To view images in HDMI, it is necessary to connect to a display that supports HDCP.

•There may be no image output if connected to a TV or display that is not compatible with the above format.

•Refer to the instruction manual of the TV or display to be connected to the SR4001/SR5001 for detailed information regarding the HDMI terminal.

*HDCP: High-bandwidth Digital Content Protection

CONNECTING HDMI DEVICES

An HDMI cable (sold separately) is used to connect the HDMI jack on the SR4001/SR5001 with the HDMI jack on a DVD player, TV, projector or other component. To transmit multichannel audio via HDMI, the connected

•Disconnecting or connecting cables with the power on can damage the equipment. Turn the power off before disconnecting or connecting cables.

•Some DVD-Audio disks disable downmixing. These types of disks are not played back correctly unless the left, center, right and surround left and right speakers, and subwoofer are connected.

•If a DVD player that does not support HDMI 1.1 is connected to the SR4001/SR5001, multi channel PCM playback is not possible even with DVD- Audio disks.

•If a DVD player or other device with DVI output is connected to the SR4001/SR5001, a separate audio cable (i.Link, optical-digital, coaxial digital or analog) is needed for the audio signals. In this case, select the connected audio input as explained in “1 INPUT SETUP”. (See page 25)

•Multi channel PCM signals and audio signals of 62 kHz or higher that are input from the HDMI jack are not output from the DIGITAL OUT jacks.

•Depending on the quiality of the cable used, the HDMI signal may be affected by noise.

•Audio units that use sampling frequencies of 128 kHz and above are not supported.

DVD player

HDMI OUTPUT

INPUT

COMPONENT

1

INPUT

VIDEO

3

MONITOR

OUT 2

INPUT

INPUT 1

R IN

VCR OUT DSS/VCR2 MONITOR OUT 2

Y

CB/PB

CR/PR

Y

CB/PB

CR/PR

Y

CB/PB CR/PR

3

4

COAX

IN

N

OUT

IN

IN

OUT

IN

OUT

1

2

3

OPT

OUT

FLASHER

DC

VCR1

DSS/VCR2

CD

TAPE

CDR/MD

DIGITAL IN

DIGITAL OUT

RC-5

IN

TRIGER

AUDIO

R

L

R

L

R

L

FRONT A

SURROUND BACK

SURROUND

CENTER

AC OUTLET

TER.

SPEAKER C/

SPEAKER

230V

50/60Hz

6-8 OHMS

MULTI SPEAKER

SYSTEMS

SWITCHED

MS

0.65A 150W

VIDEO PROJECTOR

HDMI INPUT

HDMI Ver 1.1

INPUT 2 OUTPUT

MODEL NO. SR5001

AC IN

ENGLISH

player must support multichannel audio transmission through its HDMI jack.

HDMI video streaming is compatible with DVI in principle. Therefore, it is possible to connect to a TV or monitor that has a DVI terminal using an HDMI-DVI conversion cable or plug. When connecting to a DVI terminal, connect the audio signal separately.

Notes:

•Some HDMI components can be controlled over the HDMI cable, but this receiver cannot control other components this way.

•When connected to a monitor (i.e., TV, projector, etc.) that does not support HDCP, video and audio are not output.

•DVI cables come with 24-pin and 29-pin plugs. This receiver supports 24-pin DVI-D cables; 29-pin DVI cables cannot connect to it.

•Some source devices such as DVD players do not support HDMI repeater operations like those of the SR4001/SR5001. In such case, pictures are not properly projected on monitors such as TVs and projectors.

•When multiple components are connected to this receiver, turn power to unused components off to prevent interference between them.

Satellite Tuner

HDMI OUTPUT

23