Marantz SR5001 manual Preset Memory

ENGLISH

(FM) TUNING MODE (AUTO STEREO OR MONO)

SOURCE	SET	OFF	ON
l/
SLEEP	DISPLAY	P.DIRECT	SURROUND
			LIP SYNC/
AUTO		dts	INPUT
1	2	3
CS	EX/ES	VIRTUAL	T.MODE
4	5	6
M-CH ST	STEREO	NIGHT	P.SCAN
7	8	9
	7.1CH IN	A/D	HT-EQ
CL	0	+10	MEMO
CH/ CAT	SPKR A/B	MUTE	VOLUME

When in the auto stereo mode, AUTO indicator will be illuminated on the display.

The “ST” indicator is illuminated when a stereo broadcast is tuned in.

At open frequencies, the noise is muted and the “TUNED” and “ST” indicators are not illuminated.

If the signal is weak, it may be difficult to tune into the station in stereo. In such a case, press the T-MODEbutton on the front panel or remote.

“AUTO” indicator is not illuminated, if FM stereo broadcasts are received in monaural and the “ST” indicator is not illuminated.

To return to auto stereo mode, press the T-MODEbutton or press T-MODEbutton on the remote again. AUTO indicator is illuminated on the display.

1. To select FM, press the BAND button on the front panel.

2. While pressing the MEMO button, press the 2 cursor button.

“AUTO PRESET” will appear on the display, and scanning starts from the lowest frequency.

3. Each time the tuner finds a station, scanning will pause and the station will be played for five seconds.

During this time, the following operations are possible.

The band can be changed by the BAND button.

4. If no button is pressed during this period, the current station is memorized in location Preset 02.

If you wish to skip the current station, press the 3 cursor button during this period, this station is skipped and auto presetting continues.

5. Operation stops automatically when all 50 preset memory positions are filled or when auto scanning attains the highest end of all bands. If you desire to stop the auto preset memory at anytime, press the CLEAR button.

(Using the remote control unit)

1. Tune into the radio station you desire (Refer to the “MANUAL TUNING” or “AUTO TUNING” section).

2. Press the MEMO button on the remote. “– –“ (preset number) starts blinking on the display.

3. Enter the desired preset number by pressing the numeric buttons.

Note:

When entering a single digit number (2 for example), either input “02” or just input “2” and wait for a few seconds.

RECALLING A PRESET STATION

1.	SLEEP	DISPLAY	P.DIRECT	SURROUND
				LIP SYNC/
	AUTO		dts	INPUT
1.	1	2	3
	CS	EX/ES	VIRTUAL	T.MODE
	4	5	6
	M-CH ST	STEREO	NIGHT	P.SCAN
	7	8	9
		7.1CH IN	A/D	HT-EQ
	CL	0	+10	MEMO
	CH/ CAT	SPKR A/B	MUTE	VOLUME
	REC	T.DISP	PTY	F.DIRECT
1.	- PRESET +		- TUNING +
	DISC+	ANGLE	SUB TITLE	AUDIO

(Using the remote control unit)

1. Press the P.SCAN on the remote.

“PRESET SCAN” appears on the display and then the preset station with the lowest preset number is recalled first.

2. Preset stations are recalled in sequence (No.1

→No.2 → etc.) for 5 seconds each.

No stored preset number will be skipped.

3. You can fast forward the preset stations by pressing the T continuously.

When the desired preset station is received, cancel the preset scan operation by pressing the CLEAR button or P.SCAN on the remote.

CLEARING STORED PRESET STATIONS

You can remove preset stations from the memory using the following procedure.

2.	3.				LIP SYNC/
		AUTO		dts	INPUT
		1	2	3
	2.	CS	EX/ES	VIRTUAL	T.MODE
		4	5	6
		M-CH ST	STEREO	NIGHT	P.SCAN
		7	8	9
			7.1CH IN	A/D	HT-EQ
		CL	0	+10	MEMO
	3.	CH/ CAT	SPKR A/B	MUTE	VOLUME
			MULTI/ CAT	M-SPKR

PRESET MEMORY

With this unit you can preset up to 50 FM/AM stations in any order.

For each station, you can memorize the frequency and reception mode if desired.

AUTO PRESET MEMORY

This function automatically scans the FM and AM band and enters all stations with proper signal strength into the memory.

2. 4. 2. 5. 1. 3.

AV SURROUND RECEIVER SR5001

38

MANUAL PRESET MEMORY

3.	2. 4.	SLEEP	DISPLAY	P.DIRECT	SURROUND
					LIP SYNC/
		AUTO		dts	INPUT
	3.	1	2	3
ECEIVER SR5001
		CS	EX/ES	VIRTUAL	T.MODE
		4	5	6
		M-CH ST	STEREO	NIGHT	P.SCAN
		7	8	9
			7.1CH IN	A/D	HT-EQ
	2.	CL	0	+10	MEMO
		CH/ CAT	SPKR A/B	MUTE	VOLUME
			MULTI/ CAT	M-SPKR
		INFO			MENU

(Using the SR5001)

1. Tune into the radio station you desire (Refer to the “MANUAL TUNING” or “AUTO TUNING” section).

2. Press the MEMO button on the front panel. “– –“ (preset number) starts blinking on the display.

3. Select the preset number by pressing the 1 or 2 cursor buttons, while this is still blinking (approx. 5 seconds)

4. Press the MEMO button again to enter. The display stops blinking.

The station is now stored in the specified preset memory location.

(Using the SR5001)

1. Select the desired preset station by pressing the 1 or 2 cursor buttons on the front panel

(Using the remote control unit)

1. Press the S or T buttons to select the desired preset station, or input your desired preset channel with the numeric buttons on the remote.

PRESET SCAN

	CS	EX/ES	VIRTUAL	T.MODE	1.
	7	8	9
	4	5	6
	M-CH ST	STEREO	NIGHT	P.SCAN
3.		7.1CH IN	A/D	HT-EQ	3.
	CL	0	+10	MEMO
	CH/ CAT	SPKR A/B	MUTE	VOLUME
	REC	T.DISP	PTY	F.DIRECT
	- PRESET +		- TUNING +		3.
	DISC+	ANGLE	SUB TITLE	AUDIO
	CH-SEL	V-OFF	ATT.

INFO MENU

1. Recall the preset number to be cleared with the method described in “Recalling” a preset station.

2. Press the MEMO button on the front panel or press the MEMO button on the remote.

3. The stored preset number blinks in the display for 5 seconds. While blinking, press the CLEAR button on the front panel or the remote.

4. “xx CLEAR” appears on the display to indicate that the specified preset number has been cleared.

Note:

To clear all stored preset stations, press and hold the CLEAR and the ENTER buttons for two seconds.