Marantz SR5001 Selecting Analog Audio Input or Digital Audio Input, Recording AN Analog Source

ENGLISH

SELECTING ANALOG AUDIO INPUT OR

DIGITAL AUDIO INPUT

TV	DVD	VCR	DSS
TUNER	CD	CDR	MD
TAPE	AUX1	AUX2	AMP

REMOTE CONTROLLER

RC5001SR

4	5	6
M-CH ST	STEREO	NIGHT	P.SCAN
7	8	9
	7.1CH IN	A/D	HT-EQ
CL	0	+10	MEMO
CH/ CAT	SPKR A/B	MUTE	VOLUME
	MULTI/ CAT	M-SPKR

If you have already assigned the digital inputs, you can temporarily select the audio input mode for each input source as following procedures.

Press the AMP button and press the A/D (0) button. When this button is pressed, the input mode is switched in the following sequence.

→ HDMI Auto → HDMI → Digital Auto → Digital → Analog → HDMI Auto....

In HDMI Auto mode, the types of signals being input to the digital and analog input jacks for the selected input source are detected automatically.

If no digital signal is being input, the analog input jacks are selected automatically.

In Digital and HDMI mode, input is fixed to an assigned digital input terminal.

In analog mode, the analog input jacks are selected. This selecting is temporary, so the result will not be stored in memory.

If you need to change the input mode completely, use INPUT SETUP in OSD menu system. (see page 25)

RECORDING AN ANALOG SOURCE

In normal operation, the audio or video source selected for listening through the SR4001/SR5001 is sent to the record outputs.

This means that any program you are watching or listening to may be recorded simply by placing machines connected to the outputs for TAPE OUT, CD-R/MD OUT, VCR1 OUT in the record mode.

To record the input source signal you are currently watching or listening to

1.

	- PRESET +		- TUNING +
AV SURROUND RECEIVER SR5001
	DISC+	ANGLE	SUB TITLE	AUDIO
	CH-SEL V-OFF		ATT.
1.		BASS	TREBLE
	TV	DVD	VCR	DSS
	TUNER	CD	CDR	MD
	TAPE	AUX1	AUX2	AMP

REMOTE CONTROLLER

RC5001SR

1. Select the input source to record by turning the INPUT SOURCE knob on the front panel or simply press the input selector buttons on the remote.

The input source is now selected and you may watch or listen to it as desired.

2. The currently selected input source signal is output to the TAPE OUT, CD-R/MD OUT, VCR1 OUT outputs for recording.

3. Start recording to the recording component as desired.

Recording the video from one source and the audio from another

You can add the sound from one source to the video of another source to make your own video recordings.

Below is an example of recording the sound from a compact disc player connected to CD IN and the video from a video camera connected to DSS/VCR2 to video cassette recorder connected to the VCR1 OUT jack.

1.	DISC+	ANGLE	SUB TITLE	AUDIO
	CH-SEL V-OFF		ATT.
		BASS	TREBLE
	TV	DVD	VCR	DSS
2.	TUNER	CD	CDR	MD
	TAPE	AUX1	AUX2	AMP

REMOTE CONTROLLER

RC5001SR

1. Switch the video output source to VCR1 by simply pressing the input selector buttons on the remote.

2. Switch the audio input source to CD by simply pressing the input selector buttons on the remote.

3. Now “CD” has been selected as the audio input source and “VCR1” as the video input source.

Notes:

•If you change the input source during recording, you will record the signals from the newly selected input source.

•You cannot record the surround effects.

•Digital input signals are only output to the digital outputs. There is no conversion from digital to analog.

When connecting CD players and other digital components, do not connect only the digital terminals, but the analog ones as well.

HT-EQ

AV SURROUND RECEIVER SR5001

Press the HT-EQbutton on the front panel to turn on the HT-EQ mode.

The tonal balance of a film soundtrack will be excessively bright and harsh when played back over audio equipment in the home. This is because film soundtracks were designed to be played back in large movie theater environments.

Activating the HT-EQ feature when watching a film made for movie theaters corrects this and restores the correct tonal balance.

The HT-EQ feature is available except in the following modes.

•7.1 CH INPUT

•PURE-DIRECT

•When VIRTUAL is set for the surround mode

7.1 CH INPUT

The SR4001/SR5001 is equipped for future expansion through the use of Multi channel SACD multichannel player or DVD-Audio player.

When this is selected, the input signals connected to the L(front left), R (front right), CENTER, SL (surround left), SR (surround right) and SBL (surround back left) and SBR (surround back right) channels of the 7.1 CH. In jacks are output directly to the front (left and right), center, surround (left and right) and surround back speaker systems as well as the pre-out jacks without passing through the surround circuitry.

In addition, the signal input to the SW (subwoofer) jack is output to the PRE OUT SW (subwoofer) jack. When 7.1 CH. INPUT is selected, the last video input used remains routed to the Monitor Outputs.

This permits simultaneous viewing with video sources.

2. 1.

	M-CH ST	STEREO	NIGHT	P.SCAN
AV SURROUND RECEIVER SR5001	7	8	9
2.		7.1CH IN	A/D	HT-EQ
	CL	0	+10	MEMO
	CH/ CAT	SPKR A/B	MUTE	VOLUME
4.		MULTI/ CAT	M-SPKR
	INFO			MENU
		ENTER
	T.TONE
4.	/SET UP			EXIT
	REC	T.DISP	PTY	F.DIRECT
	- PRESET +		- TUNING +
	DISC+	ANGLE	SUB TITLE	AUDIO
	CH-SEL V-OFF		ATT.
1.	BASS		TREBLE
	TV	DVD	VCR	DSS
	TUNER	CD	CDR	MD
	TAPE	AUX1	AUX2	AMP

REMOTE CONTROLLER

RC5001SR

36