Grizzly T23108 owner manual Depth stop and controls

Page 29

15.Rotate the clamp lever to the right to firmly secure the chain between the clamp plates of the chain holder.

16.Lower the grinding wheel into the cutter gullet until it stops, then thread the depth knob bolt down until it is against the depth stop (see

Figure 33).

 

 

Depth

Knob

 

 

Knob Bolt

Lock Nut

 

 

 

 

 

 

Depth Stop

Figure 33. Depth stop and controls.

Important: When adjusting the depth knob bolt, keep in mind that you want to replace and sharpen angles that may be worn or damaged. Do not make the gullet any deeper than is necessary to accomplish this.

Also, taking deep cuts with the grinding wheel could burn the metal, which will damage the temper of the steel. Chain cutters that are heated excessively during sharpening become brittle and dull quickly.

It is better to make a few light passes than one deep one!

17.Back the depth knob bolt away from the depth stop by a small amount, then thread the knob lock nut down to secure the setting.

18.Adjust the advancement guide so that the chain moves slightly to the right. This will remove a small amount from the top and side plates and provide the sharpened angles.

Note: This critical adjustment is a matter of trial-and-error and experience.

19.Connect the sharpener to power and wait for the wheel to come to full speed.

Model T23108 (Mfg. Since 7/10)

20.Using a slow and steady pace, lower the grinding wheel into the first cutter link until the depth bolt hits against the depth stop, then allow the spring-loaded swing arm to raise the grinding wheel slowly.

21.While taking care not to contact the spinning grinding wheel with your hands or the chain, rotate the clamp lever to the left enough to release the chain from the clamp plates.

22.Slowly pull the chain to the right until the advancement guide falls behind the next cutter link for that side, then pull the chain to the left to firmly seat the advancement guide against the rear of the cutter link to be sharp- ened. This will properly position the link for sharpening.

23.Re-tighten the clamp lever and repeat Steps 19–22until all cutters for that side of the chain have been sharpened.

24.Turn the sharpener OFF and wait for the grinding wheel to completely stop, then dis- connect the sharpener from power.

25.Release the chain from the clamp plates, turn it around 180° so that the cutters on the other side of the chain are ready for sharpening.

26.Rotate the chain holder to align with the angle marks on the other side of the rotation scale, and, if the chain requires a gullet angle, tilt the chain holder 10° in the opposite direc- tion.

27.When you are satisfied that the sharpener settings are correct, repeat Steps 18–23for the rest of the cutters on that side of the chain.

28.Check, and if necessary, adjust the height of the depth gauges. Refer to the next subsec- tion for more information.

29.Clean and lubricate the chain per the manu- facturer's recommendation before re-install- ing it onto the chain saw.

-27-

Page 28 Page 30
Image 29
Page 28 Page 30
Contents Chain SAW Sharpener Page Table of Contents Manual Accuracy IntroductionContact Info Machine DescriptionON/OFF IdentificationSafety Instructions for Machinery SafetyUnattended OPERATION. Never­ leave­ Additional Safety for Chain Saw Sharpeners Single-Phase Power SupplyFull-Load Current Rating at Amps Nominal Voltage 110V/120V50 ft Minimum Gauge Size 14 AWGNeeded for Setup SetupUnpacking Description QtyInventory Figure Qty InventorySite Considerations Weight LoadMachine Base Workbench MountingWorkbench To assemble the sharpener AssemblyTo install the grinding wheel Installing Grinding WheelTo test run the machine Power ConnectionChain Saw Terminology OperationsDrive Link Chain PitchPage How the Chain Cuts Grinding Wheel Selection To perform a ring test Wheel Inspection Ring TestTop Plate Angle To set up the chain holder for the top plate angleTop Plate Cutting Angle To tilt the chain holder for a 10 gullet angle Gullet AngleTo sharpen the chain cutters Sharpening OperationAdvancement guide and controls Depth stop and controls To adjust the clamp plate pressure Depth Gauge SettingClamp Plate Adjustment Cleaning MaintenanceSchedule LubricationTroubleshooting ServiceWiring Safety Instructions WiringT23108 wiring T23108 Wiring DiagramParts Breakdown DiagramDescription Parts ListComments Warranty CardBOX BELLINGHAM, WA Grizzly INDUSTRIAL, INCWarranty and Returns Warranty and ReturnsOrder Hours a DAY

T23108 specifications

Grizzly T23108 is a powerful and versatile woodworking tool designed to meet the needs of both professional woodworkers and hobbyists alike. As a table saw, it combines precision, safety, and ease-of-use, ensuring that users can execute a variety of cutting tasks with confidence and accuracy.

One of the standout features of the Grizzly T23108 is its robust construction. Built with a sturdy cast iron tabletop, it provides stability and reduces vibrations during operation, ensuring cleaner cuts and enhancing the overall durability of the saw. The table measures a generous size, allowing for larger workpieces to be handled with ease.

The T23108 is equipped with a powerful 2 HP motor that delivers impressive performance, making it suitable for cutting hardwood and other dense materials. The motor is designed to provide consistent power, even under heavy loads, ensuring that users can tackle tough tasks without the tool bogging down.

Safety is a top priority in the design of the Grizzly T23108. It features a high-quality blade guard that protects the user from accidental contact with the saw blade while cutting, and it includes riving knife technology. This feature helps to prevent kickback, a common hazard with table saws, by allowing the blade to remain aligned with the workpiece during cuts. Additionally, the saw boasts an easy-to-use emergency stop switch that can quickly disconnect power in case of an emergency.

Another key technological feature of the Grizzly T23108 is its adjustable fence system. The rip fence is easy to adjust, ensuring that users can achieve precise measurements and straight cuts consistently. The fence locks securely in place, giving users the confidence that their settings will remain accurate throughout the cutting process.

The saw also offers versatility with its capability to perform various cuts, including crosscuts and bevel cuts, thanks to its tilting blade mechanism. This adaptability makes the Grizzly T23108 an excellent choice for a range of woodworking projects, from simple DIY tasks to complex furniture building.

Overall, the Grizzly T23108 is an exceptional table saw that delivers on performance, safety, and versatility. Its superior build quality, powerful motor, and advanced safety features make it a reliable choice for anyone looking to invest in a high-quality woodworking tool. Whether you are a seasoned professional or just starting in woodworking, the Grizzly T23108 can enhance your workshop and help you achieve your crafting goals with efficiency and precision.
Top Page Image Contents