DCS PHFS-DW-SS, PHFS-DW-BK, PHFS-DWWT, PHFS-DW-BL, PHFS-DW-GN, PHFS-DW-BZ manual LP Gas Hook-Up

Page 10

LP Gas Hook-Up

LP Gas Hook-Up

The heater comes equipped with a regulator/hose assembly for connection to a standard 20 lb. / 5 gallon LP gas tank (not included) and 18” tank strap to secure the tank within the base. A dented or rusty LP tank may be hazardous and should be checked by your LP supplier.

Never use an LP tank with a damaged valve. The LP tank must be arranged to provide for vapor withdrawal from the operating cylinder.

Never connect an unregulated LP tank to the heater. The heater is shipped from the factory for LP use, never substitute gases without first converting the heater with a factory supplied conversion kit. Conversion kits are available through customer service.

LP GAS CONNECTION-REFERENCE

The heater is designed to house a 20 lb. / 5 gallon gas cylinder in the base assembly. Open the door, and place the cylinder into the housing. The regulator can then be screwed into the cylinder. The regulator and the tank have right-handed threads (clockwise to tighten no teflon tape is required). When tightening be careful not to put too much force on the cylinder valve.

CHECK THE FOLLOWING CONNECTIONS

1)Regulator to gas cylinder.

2)All connections on the hose/regulator assembly.

3)The reducer fitting and the intake pipe.

4)Intake pipe fitting at base of safety valve. The remaining connections are to be tested after the heater has been lit. (See lighting instructions on page 13).

5)Pilot tubing to safety valve.

6)Orifice fitting and Safety valve.

7)Pilot tubing and the pilot. Once leak tested, close the door and replace the valve panel.

	NOTE: Gas connections on the heater head assembly	FIG.07
	are leak tested at the factory prior to	FIG.07
	are leak tested at the factory prior to	3
	shipment.	3
	shipment.
		1
		2

GAS CYLINDER

(NOT INCLUDED)

9

Image 10

Contents Use and Care Guide Models THE PH3 PATIO HEATERPHFS-DW-SS PHFS-DW-BK PHFS-DW-WT PHFS-DW-BL PHFS-DW-GN PHFS-DW-BZ or by mail DCS Attention Customer Service PRECAUTIONFOR YOUR SAFETY WHAT TO DO IF YOU SMELL GAS A Message To Our Customers17-18 Table Of Contents19-20 Safety Practices & Precautions CHECK THE HEATER IMMEDIATELY IF ANY OF THE FOLLOWING CONDITIONS EXISTFeatures TOOLS NEEDEDSTEP Assembly InstructionsDo not tape over the first two threads at the of the intake pipe fig HARDWARE USED 1 P/N 18159 Reducer Fitting1 P/N 15001-26 #10 Machine Screws BASE COVER POST STEPHARDWARE USED CHECK THE FOLLOWING CONNECTIONS LP Gas Hook-UpLP GAS CONNECTION-REFERENCE are leak tested at the factory prior toLEAK TEST PRECAUTIONSGas Sounding Test TEST POINTSWashers - Flat 1 P/N2 P/N 15019-07 1/4 Cap Acorn Nuts 3 P/N 15005-10 Washers - Split REFLECTOR SPLIT WASHER FLAT WASHER BURNER HEADLocating Heater For Use BEFORE LIGHTING Lighting And ShutdownBEFORE TURNING THE GAS SUPPLY “ON” To lightStorage And Insect Warning CLEANINGSPIDER & INSECT WARNING Install the burner assembly by reversing the Burner Removal And InstallationBURNER INSTALLATION BURNER REMOVALPilot Cleaning Call customer service for replacement pilot assembly TroubleshootingPROBLEM available?Is there adequate gas supply? Straighten hose Check the burner and orifices forEmitter glow is uneven Level heaterParts List DESCRIPTIONNylon Washer Post AssemblyBase Assembly Reducer FittingService HOW TO OBTAIN SERVICEDCS WILL PAY FOR WarrantyLENGTH OF WARRANTY DCS WILL NOT PAY FORPage Page CHAUFFERETTE DE PATIO PH3 Guide d’utilisation et d’entretien ModèlesAVERTISSEMENT ou par courrier DCS Attention Customer ServiceÀ notre clientèle MESURE DE PRÉCAUTIONDEMONTAGE / INSTALLATION DU BRULEUR RESOLUTION DES PROBLEMESMESURES DE SECURITE ET DE PRECAUTION Table des matièresINSPECTEZ IMMEDIATEMENT LA CHAUFFERETTE DANS LES Mesures de sécurité et de précautionCIRCONSTANCES SUIVANTES Caractéristiques OUTILS NECESSAIRESInstructions de montage ETAPE1 Réf. 18159 Réducteur QUINCAILLERIE UTILISEEETAPE 1 Réf. 15001-26 Vis à métal cal. 10 COUVERCLE DE BASE MÂT ÉTAPEQUINCAILLERIE UTILISEE VERIFIEZ SOIGNEUSEMENT LES RACCORDS SUIVANTS Branchement du gazRACCORDEMENT DE LALIMENTATION - REFERENCE REMARQUE les raccords du brûleur ont été vérifiés à lusineDEPISTAGE DES FUITES MESURES DE PRECAUTIONTest détanchéité POINTS DE DETECTION DES FUITESREFLECTEUR RONDELLE OUVERTE RONDELLE PLATE BRÛLEUR Rondelles platesECROU BORGNE Dégagement à respecter Assurez-vous toujours que laération est suffisanteAVANT DALLUMER LA CHAUFFERETTE Allumage et extinctionAVANT DOUVRIR LALIMENTATION EN GAZ Pour allumerMISE EN GARDE RELATIVE AUX ARAIGNEES ET AUX INSECTES Entreposage et mise en garde relative aux insectesNETTOYAGE INSTALLATION DU BRULEUR Démontage et installation du brûleurDEMONTAGE DU BRULEUR Nettoyage du pilote nouveau. Y a-t-il une étincelle? Résolution des problèmesPROBLÈME Le réservoir de gaz est-il plein?Le tuyau dalimentation est-il tordu? Le bouton de commande est-il tourné à fond dans le sens contrairePROBLÈME Remplissez le réservoirPièces de rechange Soupape dalimentationAppui du réservoir Écrous borgnesréservoir 18 po Poignée de portePOUR LOBTENTION DU SERVICE DE GARANTIE DCS COUVRE LES FRAIS SUIVANTS GarantieDUREE DE LA GARANTIE DCS NE COUVRE PAS LES FRAIS SUIVANTSPage Lithographié aux États-Unis 01/2002 Fax 714 372-7001 Customer Service 888Part No. 17314 Rev. B Litho in USA 01/2002 Réf. 17314 Rev. B 5800 Skylab Road, Huntington Beach, CA 92647 Tel 714