DCS PHFS-DW-SS, PHFS-DW-BK, PHFS-DWWT, PHFS-DW-BL, PHFS-DW-GN, PHFS-DW-BZ Lighting And Shutdown

Page 14
 Lighting And Shutdown

BEFORE TURNING THE GAS SUPPLY “ON” Lighting And Shutdown

BEFORE TURNING THE GAS SUPPLY “ON”

Visually inspect the hose assembly for evidence of excessive abrasion, cuts or wear. If the hose leaks it must be replaced prior to use. The replacement hose assembly shall be that specified by the manufac- turer. Make sure the surrounding areas are free of combustible materials, gasoline and other flammable vapors or liquids.

BEFORE LIGHTING

For your safety, if relighting a hot heater, always wait 5 minutes. The heater should be inspected (emitter screen, gas hookup, pilot assembly) before each use, and at least annually by a qualified service person.

To light:

1)Open door.

2)Make sure regulator hose is connected to the heater intake pipe and regulator is connected to the LP tank with both connections tight and leakproof.

3)Turn supply tank valve in a counter-clockwise direction. Check for leaks by applying soapy water to the tank and hose connections.

4)Turn control knob counter clockwise to the pilot position.

5)Depress and hold in the control knob to begin pilot gas flow, hold in the control knob for (3) minutes on new installations or cylinder changes to purge air from the lines, or (5) seconds for regular relight.

6)While depressing knob, depress the igniter button which will snap indicating it has produced a spark which should light the pilot. If not, depress control again and depress the igniter until lit or match light.The pilot is located behind the match hole cover. Rotate the disc upward from the hole for match lighting or viewing (see figure 2 on page 5).

7)Once the pilot is lit, continue to hold in the control knob for 30 seconds or until the pilot remains lit after knob is released.

8)The burner may now be turned on to the full on position (all the way counter-clockwise) and then reduce to the desired heat range.

9)Close door.

Relighting:

1)Turn control knob to off position.

2)Wait (5) minutes before attempting to relight pilot.

3)Repeat steps beginning with step (4) above.

Shut down instructions:

1)Turn control knob clockwise to the off position, the burner will make a slight popping sound when extinguished.This is a normal condition.

2)Turn LP-tank gas valve clockwise to “OFF” position when heater is not in use.

13

Image 14
Contents PHFS-DW-SS PHFS-DW-BK PHFS-DW-WT PHFS-DW-BL PHFS-DW-GN PHFS-DW-BZ THE PH3 PATIO HEATERUse and Care Guide Models or by mail DCS Attention Customer Service PRECAUTIONFOR YOUR SAFETY WHAT TO DO IF YOU SMELL GAS A Message To Our Customers19-20 Table Of Contents17-18 Safety Practices & Precautions CHECK THE HEATER IMMEDIATELY IF ANY OF THE FOLLOWING CONDITIONS EXISTFeatures TOOLS NEEDEDDo not tape over the first two threads at the of the intake pipe fig Assembly InstructionsSTEP HARDWARE USED 1 P/N 18159 Reducer Fitting1 P/N 15001-26 #10 Machine Screws BASE COVER POST STEPHARDWARE USED CHECK THE FOLLOWING CONNECTIONS LP Gas Hook-UpLP GAS CONNECTION-REFERENCE are leak tested at the factory prior toLEAK TEST PRECAUTIONSGas Sounding Test TEST POINTSWashers - Flat 1 P/N2 P/N 15019-07 1/4 Cap Acorn Nuts 3 P/N 15005-10 Washers - Split REFLECTOR SPLIT WASHER FLAT WASHER BURNER HEADLocating Heater For Use BEFORE LIGHTING Lighting And ShutdownBEFORE TURNING THE GAS SUPPLY “ON” To lightSPIDER & INSECT WARNING CLEANINGStorage And Insect Warning Install the burner assembly by reversing the Burner Removal And InstallationBURNER INSTALLATION BURNER REMOVALPilot Cleaning Call customer service for replacement pilot assembly TroubleshootingPROBLEM available?Is there adequate gas supply? Straighten hose Check the burner and orifices forEmitter glow is uneven Level heaterParts List DESCRIPTIONNylon Washer Post AssemblyBase Assembly Reducer FittingService HOW TO OBTAIN SERVICEDCS WILL PAY FOR WarrantyLENGTH OF WARRANTY DCS WILL NOT PAY FORPage Page CHAUFFERETTE DE PATIO PH3 Guide d’utilisation et d’entretien ModèlesAVERTISSEMENT ou par courrier DCS Attention Customer ServiceÀ notre clientèle MESURE DE PRÉCAUTIONDEMONTAGE / INSTALLATION DU BRULEUR RESOLUTION DES PROBLEMESMESURES DE SECURITE ET DE PRECAUTION Table des matièresCIRCONSTANCES SUIVANTES Mesures de sécurité et de précautionINSPECTEZ IMMEDIATEMENT LA CHAUFFERETTE DANS LES Caractéristiques OUTILS NECESSAIRESInstructions de montage ETAPEETAPE QUINCAILLERIE UTILISEE1 Réf. 18159 Réducteur 1 Réf. 15001-26 Vis à métal cal. 10 COUVERCLE DE BASE MÂT ÉTAPEQUINCAILLERIE UTILISEE VERIFIEZ SOIGNEUSEMENT LES RACCORDS SUIVANTS Branchement du gazRACCORDEMENT DE LALIMENTATION - REFERENCE REMARQUE les raccords du brûleur ont été vérifiés à lusineDEPISTAGE DES FUITES MESURES DE PRECAUTIONTest détanchéité POINTS DE DETECTION DES FUITESECROU BORGNE Rondelles platesREFLECTEUR RONDELLE OUVERTE RONDELLE PLATE BRÛLEUR Dégagement à respecter Assurez-vous toujours que laération est suffisanteAVANT DALLUMER LA CHAUFFERETTE Allumage et extinctionAVANT DOUVRIR LALIMENTATION EN GAZ Pour allumerNETTOYAGE Entreposage et mise en garde relative aux insectesMISE EN GARDE RELATIVE AUX ARAIGNEES ET AUX INSECTES DEMONTAGE DU BRULEUR Démontage et installation du brûleurINSTALLATION DU BRULEUR Nettoyage du pilote nouveau. Y a-t-il une étincelle? Résolution des problèmesPROBLÈME Le réservoir de gaz est-il plein?Le tuyau dalimentation est-il tordu? Le bouton de commande est-il tourné à fond dans le sens contrairePROBLÈME Remplissez le réservoirPièces de rechange Soupape dalimentationAppui du réservoir Écrous borgnesréservoir 18 po Poignée de portePOUR LOBTENTION DU SERVICE DE GARANTIE DCS COUVRE LES FRAIS SUIVANTS GarantieDUREE DE LA GARANTIE DCS NE COUVRE PAS LES FRAIS SUIVANTSPage Lithographié aux États-Unis 01/2002 Fax 714 372-7001 Customer Service 888Part No. 17314 Rev. B Litho in USA 01/2002 Réf. 17314 Rev. B 5800 Skylab Road, Huntington Beach, CA 92647 Tel 714