Black & Decker LSWV36R manual Installing and Removing the Battery Pack

Page 7

LED glowing indefinitely. The charger will keep the battery pack fresh and fully charged.

Important Charging Notes

1. Longest life and best performance can be obtained if the battery pack is charged when the air temperature is between 60°F and 80°F (16°- 27°C). DO NOT charge the battery pack in an air temperature below +40°F (+4.5°C), or above +105°F (+40.5°C). This is important and will prevent serious damage to the battery pack.

2. The charger and battery pack may become warm to touch while charging. This is a normal condition, and does not indicate a problem. To facilitate the cooling of the battery pack after use, avoid placing the charger or battery pack in a warm environment such as in a metal shed, or an uninsulated trailer.

3. If the battery pack does not charge properly:

a. Check current at receptacle by plugging in a lamp or other appliance b. Check to see if receptacle is connected to a light switch which turns power off when you turn out the lights.

c. Move charger and battery pack to a location where the surrounding air temperature is approximately 60°F - 80°F (16° - 27°C).

d. If charging problems persist, take the tool, battery pack and charger to your local service center.

4. The battery pack should be recharged when it fails to produce sufficient power on jobs which were easily done previously. DO NOT CONTINUE to use under these conditions. Follow the charging procedure. You may also charge a partially used pack whenever you desire with no adverse affect on the battery pack.

5. Foreign materials of a conductive nature such as, but not limited to, steel wool, aluminum foil, or any buildup of metallic particles should be kept away from charger cavities. Always unplug the charger from the power supply when there is no battery pack in the cavity. Unplug charger before attempting to clean.

6. Do not freeze or immerse charger in water or any other liquid. WARNING: Shock hazard. Do not allow any liquid to get inside charger. Never attempt to open the battery pack for any

reason. If the plastic housing of the battery pack breaks or cracks, return to a service center for recycling.

State of charge indicator (figure B)

The back of the battery is equipped with a state of charge indicator. This can be used to display the current level of charge in the battery during use and during charging. It does not indicate tool functionality and is subject to variation based on product components, temperature and end-user application.

Checking state of charge during use:

 

 

• Press the state of charge indicator button (B1).

 

 

• The four LED’s (B2) will illuminate indicating the percent of charge in the

battery. See chart in figure B.

B

B1

• If LED light does not lluminate, charge battery.

NOTE: This battery is designed to not

B2

 

operate when a charge below 20% of its

 

 

capacity is reached. After the battery charge is

 

 

depleated, the toll will not operate until after the

 

 

battery has been recharged.

 

 

Installing and Removing the Battery Pack

WARNING: Make certain the tool is switched off before removing or installing battery.

To install battery pack:

 

Insert battery pack into tool until fully seated and an

C

audible click is heard (figure C). Make sure battery

pack is fully seated and fully latched into position.

 

To remove battery pack: Depress the

 

battery release button in the back of the battery

 

pack and pull battery pack out of tool.

 

WARNING: Before assembly, make

 

sure that the tool is switched off and the

 

battery has been removed.

 

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents VEA EL ESPA-OL EN LA Contraportada Save this manual for future referencePour LE FRANÇAIS, Voir LA Couverture ARRIÈre Important Safety warnings & instructions Table of ContentsGeneral safety warnings and instructions for all tools Components Important safety instructions For battery chargersLSWV36 Power Head Do not attempt to charge the battery pack with any chargersRecommended Minimum Wire Size for Extension Cords Important safety instructions For battery PacksHot/Cold pack delay Charging ProcedureCharger Diagnostics Bad batteryInstalling and Removing the Battery Pack Tube assembly Sweeper Mode assemblyFan Cover assembly To attach Sweeper operation OperationParts. this Sweeper is for Actions that may lead to the unit jamming are VacUUM operationWhat to do if the unit jams Figure M With a small wooden stick. Do not use a metal implement orCleaning and Storage MaintenanceAccessories How to avoid jamming the unitProblem Solution TRoubleshootingFull Three-Year Home Use Warranty Service InformationNuméro de catalogue LSWV36 Graves blessures Table DES MatièresDéfinitions Directives ET Avertissements DE Sécurité ImportantsLire et respecter toutes les mesures de sécurité Générales Pour Tous LES OutilsUniquement des pièces de rechange Black & Decker Avertissement risque de choc électrique ComposantesTenir le cordon éloigné des surfaces chauffées Calibre de fil minimum recommandé pour les rallongesProtéger le chargeur de la pluie et de la neige NE Jamais tenter de relier deux chargeurs ensemble Directives de sÉcuritÉ importantes pour Les blocs-pilesPile en mauvais état Recommandations en matière de rangementFonctions de diagnostic du chargeur Procédure de chargeIndicateur DE L’ÉTAT DE Charge Figure B Indicateur de L’état De charge figure BPile laissée dans le chargeur Remarques importantes pour le chargementSAC Collecteur Figure D Assemblage DU Mode BalayeuseInsertion et retrait du bloc-piles Insertion DU BLOC-PILESFonctionnement InterrupteurLe sac avant de réutiliser l’appareil Fonctionnement DE LA BalayeuseComment Éviter LE Blocage DE L’APPAREIL AccessoiresEntretien Actions Pouvant Entraîner LE Blocage DE L’APPAREILDEpannage Page Modelo N LSWV36 Importantes DE Seguridad ÍndicePautas DE SEGURIDAD/DEFINICIONES Advertencias E Instrucciones30 Guárdese bajo techo Tenga Mucho Cuidado cuando limpie en escalonesComponentes Conserve Estas Instrucciones No exponga el cargador a la lluvia ni a la nieveRecomendaciones con respecto al almacenamiento Dejar la batería en el cargador Procedimiento de cargaBatería en mal estado Retraso por paquete caliente/fríoLa carga. Éste no indica la capacidad de IndicaDOr deL Estado de la carga figure BInstalación y extracción del paquete de Ensamblaje EN Modo DE BarredoraEnsamblaje DEL Tubo Aspirador Figuras E, F Y G Ensamblaje EN Modo DE AspiradoraOperación Bolsa DE Recolección Figura DNota Asegúrese de que la barredora Anteojos de seguridad. Use unaRopa holgada lejos de las aberturas y las Piezas en movimiento. Esta BarredoraCómo Evitar LA Obstrucción DE LA Unidad MantenimientoLimpieza Y Almacenamiento El sello Rbrc Detección de problemasAccesorios Información de mantenimientoSolamente para Propósitos de México Garantía completa de tres años para Uso en el hogarPage Page Page Solamente Para Propositos DE Mexico

LSWV36, LSWV36R specifications

The Black & Decker LSWV36 and LSWV36R are versatile cordless leaf blowers that embody efficiency and convenience for outdoor maintenance. These models provide exceptional power in a lightweight design, making them ideal for homeowners looking to keep their yards tidy without the hassle of cords or gas.

One of the standout features of the LSWV36 and LSWV36R is the 36-volt lithium-ion battery. This technology ensures longer run times and faster charging, allowing users to complete their tasks without frequent interruptions. The battery delivers consistent power, ensuring that the blower operates at peak performance until the charge is exhausted. Users can expect up to 30 minutes of runtime on a single charge, which is generally sufficient for most residential lawns.

Both models boast a powerful wind speed of up to 120 mph, allowing for efficient leaf removal and debris clearance from sidewalks, driveways, and patios. The lightweight and ergonomic design of the blowers makes them easy to maneuver, reducing arm fatigue during extended use. Weighing approximately 7.5 pounds, these leaf blowers are manageable for users of all ages.

The LSWV36 and LSWV36R come equipped with two speed settings, providing the flexibility to tackle different tasks. The lower speed setting is perfect for clearing grass clippings, while the higher speed is ideal for moving stubborn leaves and heavier debris. This feature ensures that users have control over the tool's performance, adapting to the specific needs of their outdoor spaces.

Moreover, the LSWV36R model features a vacuum and mulching system, which adds to its versatility. Users can easily switch from blowing leaves to vacuuming them up, transforming yard waste into mulch for composting or garden use. This dual functionality not only saves time but also assists in creating an eco-friendly gardening solution.

In summary, the Black & Decker LSWV36 and LSWV36R deliver powerful performance, runtime efficiency, and dual functionality, making them indispensable tools for maintaining a clean and orderly yard. They combine innovative technology with user-friendly features, providing an excellent solution for anyone seeking a reliable cordless leaf blower. Whether blowing leaves or mulching yard waste, these models are sure to exceed expectations.
Top Page Image Contents