Meridian Audio FPP-42HD20, FPP-50HD20, FPP-61HD20 operation manual Basic Operations

Page 16

Basic Operations

POWER

To turn the unit ON and OFF:

1.Plug the power cord into an active AC power outlet.

2.Press the Power button (on the unit).

The monitor’s POWER/STANDBY indicator turns red and the standby mode is set.

3.Press the POWER ON button (on the remote control) to turn on the unit.

The monitor’s POWER/STANDBY indicator will light up (green) when the unit is on.

4.Press the POWER STANDBY button (on the remote control) or the Power button (on the unit) to turn off the unit.

The monitor’s POWER/STANDBY indicator turns red and the standby mode is set (only when turning off the unit with the remote control).

VOLUME

To adjust the sound volume:

1.Press and hold the VOLUME button (on the remote control or the unit) to increase to the desired level.

2.Press and hold the VOLUMEbutton (on the remote control or the unit) to decrease to the desired level.

MUTE

To cancel the sound:

Press the MUTE button on the remote control to cancel the sound; press again to restore.

DISPLAY

To check the settings:

1.The screen changes each time the DISPLAY button is pressed.

2.If the button is not pressed for approximately three seconds, the menu turns off.

DIGITAL ZOOM

Digital zoom specifies the picture position and enlarges the picture.

1.Press the POINTER button to display the pointer. ()

To change the size of the picture:

Press the ZOOM+ button and enlarge the picture.

The pointer will change to resemble a magnifying

glass. ( )

A press of the ZOOM- button will reduce the picture and return it to its original size.

To change the picture position:

Select the position with the ▲▼ buttons.

2.Press the POINTER button to delete the pointer.

AUTO ADJUST

To adjust the size or quality of the picture automatically:

Press the AUTO ADJUST button.

Information

AUTO ADJUST ON setting

When RGB (still picture) input

is selected ...... Fine Picture, Picture ADJ, Position,

and Contrast will be adjusted automatically.

When RGB (motion picture),

VIDEO, or Y/Pb/Pr (component) input

is selected ...... The screen size switches to ZOOM

mode automatically with the superimposed caption displayed fully only when the picture contains dark areas above and below the picture.

10

Image 16

Contents Digital Cinema Series Important Information PrecautionsRisk of Electric Shock Do not Open Use only with120V50/60HzAC power Plasma monitor cleaning procedureTo avoid damage and prolong operating life Recommendations to avoid or minimize phosphor burn-inPrécautions Recommandations importantesMises en garde et précautions de sécurité Méthode de nettoyage du moniteur à plasma Contents How to Attach Options to the Plasma Monitor Ventilation Requirements for enclosure mountingTurns the monitor’s power on and off Receives the signals from the remote controlPart Names and Function Front ViewRear View/ Terminal Board RGB2Remote Control Battery Installation and Replacement Transmits the remote control signalsNot functional for the models covered in this manual Clears the number set by the ID Select buttonHandling the remote control Using the wired remote control modeOperating Range Installation Connections Pin Assignments and Signal Levels for 15 pin RGB Analog Signal AnalogBasic Operations To set the off timer To cancel the off timerAfter the power is turned off with the off timer To check the remaining timeWhen viewing videos or digital video discs Wide OperationsWide Screen Operation with Computer Signals When Picture Size is set to OFF Supported resolution Picture Size setting Advanced menu mode Menu OperationsReset Menu TreeOPTION2 PWR. MGT Picture Settings Menu Adjusting the picture Picture adjustment screen Adjusting for the video processorAdjusting the color to the desired level Setting the color temperatureReducing noise in the picture Making the Low Tone adjustments Adjusting the white balance Gamma settings LOW Tone settingsAudio Settings Menu Adjusting the colors Color Tune settings Audio settings menuImage Adjust Settings Menu Setting the allocation of the audio connectorsAdjusting the Position, Size, Fine Picture, Picture Adj Example Setting Audio INPUT1 to VideoOption1 Settings Menu Setting the on-screen menuSetting the BNC connectors Checking the signal being transmitted to RGB1 terminalSetting a computer image to the correct RGB select screen OSM Orbiter settingsSetting high definition images to the suitable screen size Setting the Input Skip Input Skip settings RGB Select modesResetting to the default values Option2 Settings MenuSetting the power management for computer images POWER/STANDBY indicator Setting the picture to suit the movie PLE settings Reducing burn-in of the screen Orbiter Function settings Orbiter settings Inverse Settings To select on for the Working Time Setting the timeScreen Wiper Setting the screen size for S1/S2 video input Soft Focus settings Gray Level settings SpeedSetting the picture size for RGB input signals Setting the signal and black level for DVI signal S1/S2 settings PLUG/PLAY settingsOption3 Settings Menu Using the timer Present Time settings Present TimeSetting the power on mode To reset the program To reset the data Special characters in the Program Timer screenEnabling/disabling remote control wireless transmission PWR. on Mode settings Control Lock settings IR Remote settingsLoop Out setting ID number settingVideo Wall setting Divider settings Video Wall Position settings Divider DISP. Mode settings Auto ID settings Image Adjust settings On Delay Power on delay P. on Delay settings PLE Link settings PLE LinkAdvanced OSM Settings Menu Setting the menu modeRepeat Timer Repeat Timer settingsLanguage Settings Menu Color System Settings MenuSetting the language for the menus Setting the video signal formatExternal Control ApplicationConnections Communication ParametersTroubleshooting Symptom Checks RemedyPage Limited Warranty Plasma Monitors This warranty may be enforced only by the first purchaserFor More Information Telephone 408 735 Faroudja Palomar Ave Sunnyvale, CA