Meridian Audio FPP-42HD20 Wide Screen Operation with Computer Signals, Supported resolution

Page 19

Wide Screen Operation with Computer Signals

Switch to the wide screen mode to expand the 4 : 3 image to fill the entire screen.

1.Press the WIDE button on the remote control.

2.Within 3 seconds ...

Press the WIDE button again.

The screen size switches as follows:

Α NORMAL Α FULL Α ZOOM

NORMAL size screen (4:3 or SXGA 5:4)

The picture has the same size as the normal computer image.

FULL size screen

The image is expanded in the horizontal direction.

ZOOM size screen

When wide signals are input.

FULL size screen

When “PICTURE SIZE” is set to “OFF”

*This cannot be set in some models. “TRUE size” will not be displayed in such cases.

The screen size switches as follows:

ΑTRUE Α FULL Α ZOOM

TRUE size screen (VGA, SVGA 4:3)

The image is true resolution.

FULL size screen

The image is expanded in the horizontal and vertical direction.

ZOOM size screen

When wide signals are input.

TRUE

The image is true resolution.

FULL

Information

Supported resolution

See page 7 of Model Information for details on the display output of the various VESA signal standards supported by the monitor.

“PICTURE SIZE” setting

When the setting of “PICTURE SIZE” is OFF, the size of RGB-input pictures will be TRUE in place of

NORMAL.

When 852 (848) dot 480 line wide VGA* signals with a vertical frequency of 60 Hz and horizontal frequency of 31.7 (31.0) kHz are in- put

Select an appropriate setting for RGB SELECT mode referring to the“Table of Signals Supported” on page 7 of Model Information.

*“VGA”, “SVGA” and “SXGA” are registered trademarks of IBM, Inc. of the United States.

Note:

Do not allow the displayed in 4:3 mode for an extended period. This can cause a phosphor burn-in.

13

Image 19

Contents Digital Cinema Series Important Information PrecautionsRisk of Electric Shock Do not Open Recommendations to avoid or minimize phosphor burn-in Use only with120V50/60HzAC powerPlasma monitor cleaning procedure To avoid damage and prolong operating lifePrécautions Recommandations importantesMises en garde et précautions de sécurité Méthode de nettoyage du moniteur à plasma Contents Ventilation Requirements for enclosure mounting How to Attach Options to the Plasma MonitorFront View Turns the monitor’s power on and offReceives the signals from the remote control Part Names and FunctionRGB2 Rear View/ Terminal BoardRemote Control Clears the number set by the ID Select button Battery Installation and ReplacementTransmits the remote control signals Not functional for the models covered in this manualHandling the remote control Using the wired remote control modeOperating Range Installation Connections Signal Analog Pin Assignments and Signal Levels for 15 pin RGB AnalogBasic Operations To check the remaining time To set the off timerTo cancel the off timer After the power is turned off with the off timerWide Operations When viewing videos or digital video discs Picture Size setting Wide Screen Operation with Computer SignalsWhen Picture Size is set to OFF Supported resolutionMenu Operations Advanced menu modeMenu Tree ResetOPTION2 PWR. MGT Adjusting for the video processor Picture Settings MenuAdjusting the picture Picture adjustment screenAdjusting the color to the desired level Setting the color temperatureReducing noise in the picture LOW Tone settings Making the Low Tone adjustments Adjusting the white balance Gamma settings Audio settings menu Audio Settings MenuAdjusting the colors Color Tune settingsExample Setting Audio INPUT1 to Video Image Adjust Settings MenuSetting the allocation of the audio connectors Adjusting the Position, Size, Fine Picture, Picture AdjSetting the on-screen menu Option1 Settings Menu OSM Orbiter settings Setting the BNC connectorsChecking the signal being transmitted to RGB1 terminal Setting a computer image to the correct RGB select screen RGB Select modes Setting high definition images to the suitable screen sizeSetting the Input Skip Input Skip settingsResetting to the default values Option2 Settings MenuSetting the power management for computer images Reducing burn-in of the screen POWER/STANDBY indicatorSetting the picture to suit the movie PLE settings Orbiter Function settings Orbiter settings Inverse Settings To select on for the Working Time Setting the timeScreen Wiper Speed Setting the screen size for S1/S2 video input Soft Focus settings Gray Level settings PLUG/PLAY settings Setting the picture size for RGB input signalsSetting the signal and black level for DVI signal S1/S2 settingsPresent Time Option3 Settings MenuUsing the timer Present Time settings Special characters in the Program Timer screen Setting the power on mode To reset the program To reset the data IR Remote settings Enabling/disabling remote control wireless transmission PWR. on Mode settings Control Lock settingsID number setting Loop Out settingDivider Video Wall setting Divider settings Video Wall Position settings DISP. Mode settings Auto ID settings Image Adjust settings PLE Link On Delay Power on delay P. on Delay settings PLE Link settings Repeat Timer settings Advanced OSM Settings MenuSetting the menu mode Repeat TimerSetting the video signal format Language Settings MenuColor System Settings Menu Setting the language for the menusCommunication Parameters External ControlApplication ConnectionsSymptom Checks Remedy TroubleshootingPage Telephone 408 735 Faroudja Palomar Ave Sunnyvale, CA Limited Warranty Plasma MonitorsThis warranty may be enforced only by the first purchaser For More Information