Meridian Audio FPP-42HD20  Setting the time,  To select on for the Working Time, Screen Wiper

Page 34

Setting the time for INVERSE/WHITE

Set a time duration.

Example: Setting to that the INVERSE mode starts in 2 hours and proceeds for one hour and a half.

Perform Steps 1-3 of INVERSE, then...

4.Use the  and  buttons to select “ON”, then press the MENU/ENTER button.

THE “INVERSE/WHITE” screen appears.

5.Adjust the time using the ▲▼ and  buttons.

The mode switches as follows each time the  or  button is pressed:

• WORKING TIME

ΑON Χ 00H03M Χ 00H06M Χ ..... Χ 12H42M Χ 12H45M≅

• WAITING TIME

Α00H03M Χ 00H06M Χ 00H09M Χ ... Χ 12H42M Χ 12H45M≅

INVERSE/WHITE

 

WORKING TIME

:

01H30M

WAITING TIME

:

02H00M

SEL.

ADJ.

EXIT

RETURN

Information

Setting the time

WORKING TIME ..... Set the time duration for

“INVERSE/WHITE”.

When the WORKING TIME is set to “ON” the mode will stay on.

WAITING TIME ...... Set the standby time until the

“INVERSE/WHITE” mode starts.

*The “WAITING TIME” can not be set when the “WORKING TIME” is ON.

*THE “WORKING TIME” and “WAITING TIME” can be set for up to 12 hours and 45 minutes in units of 3 minutes.

*Ending a WORKING TIME function, the monitor will

be STAND BY. [Example]

WORKING TIME: 01H30M

WAITING TIME: 02H00M

≅<<<< 2 H

<<<<Α≅<< 1.5 H <<Α≅<<<<

Start

INVERSE/WHITE Start STAND BY

To select “ON” for the “WORKING TIME”...

Set the hours of the working time to 0H and the minutes to 0M. “ON” will be displayed.

SCREEN WIPER

When this is set to ON, a white vertical bar moves repeatedly from the left and of the screen to the right end at a constant speed.

Example: Setting “SCREEN WIPER” to “ON”

Perform Steps 1-2 of LONG LIFE, then...

3.Use the ▲ and ▼ buttons to select “SCREEN WIPER”.

4.Use the  and  buttons to select “ON”.

The mode switches as follows each time the  or  button is pressed:

OFF Χ ON

 

 

 

LONG LIFE

 

 

PLE

:

AUTO

ORBITER

:

OFF

INVERSE

:

OFF

 

SCREEN WIPER

:

ON

 

 

 

 

 

SOFT FOCUS

:

OFF

 

 

SEL.

ADJ.

 

RETURN

 

 

EXIT

Information

SCREEN WIPER

ON ......... The white vertical bar appears.

You can set the time by pressing the MENU/ ENTER button while “ON” is set.

OFF ....... Screen wiper mode does not function.

Setting the time for SCREEN WIPER

Set a time duration and the speed.

Example: Setting to that the SCREEN WIPER mode starts in 30 minutes and proceeds for one hour and a half.

Perform Steps 1-3 of SCREEN WIPER, then...

4.Use the  and  buttons to select “ON”, then press the MENU/ENTER button.

THE “SCREEN WIPER” screen appears.

5.Adjust the time and speed using the ▲▼ and  buttons. The mode switches as follows each time the  or  button is pressed:

• WORKING TIME

ΑON Χ 00H03M Χ 00H06M Χ ..... Χ 12H42M Χ 12H45M≅

• WAITING TIME

Α00H03M Χ 00H06M Χ 00H09M Χ ... Χ 12H42M Χ 12H45M≅

• SPEED

Α1 Χ 2 Χ 3 Χ 4 Χ 5≅

SCREEN WIPER

WORKING TIME

:

01H30M

WAITING TIME

:

00H30M

SPEED

:

3

 

SEL.

ADJ.

 

RETURN

EXIT

28

Page 33 Page 35
Image 34
Page 33 Page 35
Contents Digital Cinema Series Important Information PrecautionsRisk of Electric Shock Do not Open To avoid damage and prolong operating life Use only with120V50/60HzAC powerPlasma monitor cleaning procedure Recommendations to avoid or minimize phosphor burn-inPrécautions Recommandations importantesMises en garde et précautions de sécurité Méthode de nettoyage du moniteur à plasma Contents How to Attach Options to the Plasma Monitor Ventilation Requirements for enclosure mountingPart Names and Function Turns the monitor’s power on and offReceives the signals from the remote control Front ViewRear View/ Terminal Board RGB2Remote Control Not functional for the models covered in this manual Battery Installation and ReplacementTransmits the remote control signals Clears the number set by the ID Select buttonHandling the remote control Using the wired remote control modeOperating Range Installation Connections Pin Assignments and Signal Levels for 15 pin RGB Analog Signal AnalogBasic Operations After the power is turned off with the off timer To set the off timerTo cancel the off timer To check the remaining timeWhen viewing videos or digital video discs Wide Operations Supported resolution Wide Screen Operation with Computer SignalsWhen Picture Size is set to OFF  Picture Size setting Advanced menu mode Menu OperationsReset Menu TreeOPTION2 PWR. MGT  Picture adjustment screen Picture Settings MenuAdjusting the picture  Adjusting for the video processorAdjusting the color to the desired level Setting the color temperatureReducing noise in the picture  Gamma settings Making the Low Tone adjustments Adjusting the white balance  LOW Tone settings Color Tune settings Audio Settings MenuAdjusting the colors  Audio settings menuAdjusting the Position, Size, Fine Picture, Picture Adj Image Adjust Settings MenuSetting the allocation of the audio connectors Example Setting Audio INPUT1 to VideoOption1 Settings Menu Setting the on-screen menuSetting a computer image to the correct RGB select screen Setting the BNC connectorsChecking the signal being transmitted to RGB1 terminal  OSM Orbiter settings Input Skip settings Setting high definition images to the suitable screen sizeSetting the Input Skip  RGB Select modesResetting to the default values Option2 Settings MenuSetting the power management for computer images  PLE settings POWER/STANDBY indicatorSetting the picture to suit the movie Reducing burn-in of the screen Orbiter Function settings  Orbiter settings Inverse Settings  To select on for the Working Time  Setting the timeScreen Wiper  Gray Level settings Setting the screen size for S1/S2 video input Soft Focus settings Speed S1/S2 settings Setting the picture size for RGB input signalsSetting the signal and black level for DVI signal  PLUG/PLAY settings Present Time settings Option3 Settings MenuUsing the timer Present Time To reset the data Setting the power on mode To reset the program  Special characters in the Program Timer screen Control Lock settings Enabling/disabling remote control wireless transmission PWR. on Mode settings  IR Remote settingsLoop Out setting ID number setting Video Wall Position settings Video Wall setting Divider settings Divider DISP. Mode settings  Auto ID settings Image Adjust settings  PLE Link settings On Delay Power on delay P. on Delay settings PLE LinkRepeat Timer Advanced OSM Settings MenuSetting the menu mode  Repeat Timer settingsSetting the language for the menus Language Settings MenuColor System Settings Menu Setting the video signal formatConnections External ControlApplication Communication ParametersTroubleshooting Symptom Checks RemedyPage For More Information Limited Warranty Plasma MonitorsThis warranty may be enforced only by the first purchaser Telephone 408 735 Faroudja Palomar Ave Sunnyvale, CA
Top Page Image Contents