Meridian Audio FPP-61HD20, FPP-50HD20, FPP-42HD20 Menu Operations, Advanced menu mode

Page 20

OSM(On Screen Menu) Controls

Menu Operations

The OSM window is displayed with respect to the screen as shown on the diagram.

*Depending on the screen’s mode, the OSM may be displayed differently.

In the explanation, the OSM section is shown close up.

		MAIN MENU			1 / 2
	PICTURE

	AUDIO
	IMAGE ADJUST
	OPTION1
	ADVANCED OSM			:	OFF
	NEXT PAGE
	SEL.	MENU/ENTER	OK		EXIT	EXIT

The following describes how to use the menus and the selected items.

1.Press the MENU/ENTER button on the remote control to display the MAIN MENU.

				MAIN MENU			1 / 2
	PICTURE

AUDIO
IMAGE ADJUST
OPTION1
ADVANCED OSM						:	OFF
		NEXT PAGE
		SEL.		MENU/ENTER	OK		EXIT	EXIT

				MAIN MENU			2 / 2
		PREVIOUS PAGE
	LANGUAGE
COLOR SYSTEM
SOURCE INFORMATION
		SEL.			OK			EXIT
				MENU/ENTER
				MENU/ENTER			EXIT

2.Press the cursor buttons ▲ ▼ on the remote control to highlight the menu you wish to enter.

3.Press the MENU/ENTER button on the remote control to select a sub menu or item.

			PICTURE		1 / 2
	CONTRAST

	BRIGHTNESS
	SHARPNESS
	COLOR
	COLOR
	TINT
	PICTURE MODE			:	NORMAL
	NR			:	OFF
	NEXT PAGE
	SEL.		ADJ.		EXIT	RETURN

4.Adjust the level or change the setting of the selected item by using the cursor buttons on the remote control.

5.The adjustments or the settings that are stored in memory.

The change is stored until you change it again.

6.Repeat steps 2 – 5 to adjust an additional item, or press the EXIT button on the remote control to return to the main menu.

Note: The main menu disappears by pressing the EXIT button.

Information

Advanced menu mode

When “ADVANCED OSM” is set to “ON” in the main menu (1/2), full menu items will be shown.

MAIN MENU

1 / 2

PICTURE

AUDIO

IMAGE ADJUST

OPTION1

OPTION2

OPTION3

ADVANCED OSM			: ON
NEXT PAGE
SEL.	MENU/ENTER	OK		EXIT	EXIT

14

Image 20

Contents Digital Cinema Series Risk of Electric Shock Do not Open PrecautionsImportant Information Use only with120V50/60HzAC power Plasma monitor cleaning procedureTo avoid damage and prolong operating life Recommendations to avoid or minimize phosphor burn-inMises en garde et précautions de sécurité Recommandations importantesPrécautions Méthode de nettoyage du moniteur à plasma Contents How to Attach Options to the Plasma Monitor Ventilation Requirements for enclosure mountingTurns the monitor’s power on and off Receives the signals from the remote controlPart Names and Function Front ViewRear View/ Terminal Board RGB2Remote Control Battery Installation and Replacement Transmits the remote control signalsNot functional for the models covered in this manual Clears the number set by the ID Select buttonOperating Range Using the wired remote control modeHandling the remote control Installation Connections Pin Assignments and Signal Levels for 15 pin RGB Analog Signal AnalogBasic Operations To set the off timer To cancel the off timerAfter the power is turned off with the off timer To check the remaining timeWhen viewing videos or digital video discs Wide OperationsWide Screen Operation with Computer Signals When Picture Size is set to OFF Supported resolution Picture Size setting Advanced menu mode Menu OperationsReset Menu TreeOPTION2 PWR. MGT Picture Settings Menu Adjusting the picture Picture adjustment screen Adjusting for the video processorReducing noise in the picture Setting the color temperatureAdjusting the color to the desired level Making the Low Tone adjustments Adjusting the white balance Gamma settings LOW Tone settingsAudio Settings Menu Adjusting the colors Color Tune settings Audio settings menuImage Adjust Settings Menu Setting the allocation of the audio connectorsAdjusting the Position, Size, Fine Picture, Picture Adj Example Setting Audio INPUT1 to VideoOption1 Settings Menu Setting the on-screen menuSetting the BNC connectors Checking the signal being transmitted to RGB1 terminalSetting a computer image to the correct RGB select screen OSM Orbiter settingsSetting high definition images to the suitable screen size Setting the Input Skip Input Skip settings RGB Select modesSetting the power management for computer images Option2 Settings MenuResetting to the default values POWER/STANDBY indicator Setting the picture to suit the movie PLE settings Reducing burn-in of the screen Inverse Settings Orbiter settings Orbiter Function settings Screen Wiper Setting the time To select on for the Working Time Setting the screen size for S1/S2 video input Soft Focus settings Gray Level settings SpeedSetting the picture size for RGB input signals Setting the signal and black level for DVI signal S1/S2 settings PLUG/PLAY settingsOption3 Settings Menu Using the timer Present Time settings Present TimeSetting the power on mode To reset the program To reset the data Special characters in the Program Timer screenEnabling/disabling remote control wireless transmission PWR. on Mode settings Control Lock settings IR Remote settingsLoop Out setting ID number settingVideo Wall setting Divider settings Video Wall Position settings Divider Image Adjust settings Auto ID settings DISP. Mode settings On Delay Power on delay P. on Delay settings PLE Link settings PLE LinkAdvanced OSM Settings Menu Setting the menu modeRepeat Timer Repeat Timer settingsLanguage Settings Menu Color System Settings MenuSetting the language for the menus Setting the video signal formatExternal Control ApplicationConnections Communication ParametersTroubleshooting Symptom Checks RemedyPage Limited Warranty Plasma Monitors This warranty may be enforced only by the first purchaserFor More Information Telephone 408 735 Faroudja Palomar Ave Sunnyvale, CA