Meridian Audio FPP-50HD20 Reducing noise in the picture, Setting the color temperature

Page 24

Reducing noise in the picture

Use these settings if the picture has noise due to poor reception or when playing video tapes on which the picture quality is poor.

Example: Setting “NR-3”

1.On the MAIN MENU, select “PICTURE”, then press the MENU/ENTER button.

The “PICTURE” screen appears.

2.Use the ▲ and ▼ buttons to select “NR”.

 

 

 

PICTURE

 

1 / 2

CONTRAST

 

 

 

 

 

 

BRIGHTNESS

 

 

 

 

 

 

SHARPNESS

 

 

 

 

 

 

COLOR

 

 

 

 

 

 

 

 

 

 

 

 

TINT

 

 

 

 

 

 

PICTURE MODE

 

:

NORMAL

 

 

NR

 

 

:

OFF

 

 

NEXT PAGE

 

 

 

 

 

 

 

SEL.

ADJ.

 

EXIT

RETURN

3.Use the  and  buttons to select “NR-3”.

The mode switches as follows each time the  or  button is pressed:

Α OFF Χ NR-1 Χ NR-2 Χ NR-3 ≅

 

 

NR

: NR-3

 

 

*If neither the  or  button is pressed within 5 seconds, the current selection is set and the previous screen reappears.

Information

NR

*“NR” stands for Noise Reduction.

*This function reduces noise in the picture.

Types of noise reduction

There are three types of noise reduction. Each has a different level of noise reduction.

The effect becomes stronger as the number increases (in the order NR-1Α NR-2Α NR-3).

OFF

Turns the noise reduction function off.

Setting the color temperature

Use this procedure to set color tone produced by the plasma display.

Example: Setting “HIGH”

1.On the MAIN MENU, select “PICTURE”, then press the MENU/ENTER button.

The “PICTURE” screen appears.

2.Use the ▲ and ▼ buttons to select “COLOR TEMP.”.

3.Use the  and  buttons to select “HIGH”.

The mode switches as follows each time the  or  button is pressed:

Α LOW Χ MID LOW Χ MID Χ HIGH ≅

* See below to set “WHITE BALANCE”.

 

 

 

PICTURE

 

2 / 2

 

 

PREVIOUS PAGE

 

 

 

 

COLOR TEMP.

 

:

HIGH

 

 

 

 

 

 

GAMMA

 

:

2

 

LOW TONE

 

:

AUTO

COLOR TUNE

 

 

 

 

 

 

SEL.

ADJ.

 

 

RETURN

 

 

 

EXIT

*If neither the  or  button is pressed within 5 seconds, the current selection is set and the previous screen reappears.

Information

Setting the color temperature

LOW

Redder

MID LOW

Slightly redder

MID

Standard (slightly bluer)

HIGH

Bluer

Restoring the factory default settings

Select “ALL RESET” under the OPTION1 menu. Note that this also restores other settings to the factory defaults.

Adjusting the color to the desired level

THIS HAS BEEN OPTIMIZED BY FAROUDJA DO NOT CHANGE

Example: Adjusting the “GAIN RED” of “HIGH” color temperature

Set “ADVANCED OSM” to “ON” in the main menu (1/ 2), then perform the following operations.

Perform Steps 1-3 of COLOR TEMP., then...

4.Press the MENU/ENTER button.

The “WHITE BALANCE” screen appears.

5.Use the ▲ and ▼ buttons to select “GAIN RED”.

WHITE BALANCE

COLOR TEMP. HIGH

GAIN RED

 

 

GAIN GREEN

 

 

GAIN BLUE

 

 

BIAS RED

 

 

BIAS GREEN

 

 

BIAS BLUE

 

 

RESET

 

: OFF

SEL.

ADJ.

EXIT RETURN

18

Page 23 Page 25
Image 24
Page 23 Page 25
Contents Digital Cinema Series Precautions Important InformationRisk of Electric Shock Do not Open Use only with120V50/60HzAC power Plasma monitor cleaning procedureTo avoid damage and prolong operating life Recommendations to avoid or minimize phosphor burn-inRecommandations importantes PrécautionsMises en garde et précautions de sécurité Méthode de nettoyage du moniteur à plasma Contents How to Attach Options to the Plasma Monitor Ventilation Requirements for enclosure mountingTurns the monitor’s power on and off Receives the signals from the remote controlPart Names and Function Front ViewRear View/ Terminal Board RGB2Remote Control Battery Installation and Replacement Transmits the remote control signalsNot functional for the models covered in this manual Clears the number set by the ID Select buttonUsing the wired remote control mode Handling the remote controlOperating Range Installation Connections Pin Assignments and Signal Levels for 15 pin RGB Analog Signal AnalogBasic Operations To set the off timer To cancel the off timerAfter the power is turned off with the off timer To check the remaining timeWhen viewing videos or digital video discs Wide OperationsWide Screen Operation with Computer Signals When Picture Size is set to OFF Supported resolution  Picture Size setting Advanced menu mode Menu OperationsReset Menu TreeOPTION2 PWR. MGT Picture Settings Menu Adjusting the picture Picture adjustment screen  Adjusting for the video processorSetting the color temperature Adjusting the color to the desired levelReducing noise in the picture Making the Low Tone adjustments  Adjusting the white balance Gamma settings  LOW Tone settingsAudio Settings Menu Adjusting the colors Color Tune settings  Audio settings menuImage Adjust Settings Menu Setting the allocation of the audio connectorsAdjusting the Position, Size, Fine Picture, Picture Adj Example Setting Audio INPUT1 to VideoOption1 Settings Menu Setting the on-screen menuSetting the BNC connectors Checking the signal being transmitted to RGB1 terminalSetting a computer image to the correct RGB select screen  OSM Orbiter settingsSetting high definition images to the suitable screen size Setting the Input Skip Input Skip settings  RGB Select modesOption2 Settings Menu Resetting to the default valuesSetting the power management for computer images POWER/STANDBY indicator Setting the picture to suit the movie PLE settings Reducing burn-in of the screen Orbiter settings  Orbiter Function settings Inverse Settings  Setting the time  To select on for the Working TimeScreen Wiper Setting the screen size for S1/S2 video input  Soft Focus settings Gray Level settings SpeedSetting the picture size for RGB input signals Setting the signal and black level for DVI signal S1/S2 settings  PLUG/PLAY settingsOption3 Settings Menu Using the timer Present Time settings Present TimeSetting the power on mode  To reset the program To reset the data  Special characters in the Program Timer screenEnabling/disabling remote control wireless transmission  PWR. on Mode settings Control Lock settings  IR Remote settingsLoop Out setting ID number settingVideo Wall setting  Divider settings Video Wall Position settings Divider Auto ID settings  DISP. Mode settings Image Adjust settings On Delay Power on delay  P. on Delay settings PLE Link settings PLE LinkAdvanced OSM Settings Menu Setting the menu modeRepeat Timer  Repeat Timer settingsLanguage Settings Menu Color System Settings MenuSetting the language for the menus Setting the video signal formatExternal Control ApplicationConnections Communication ParametersTroubleshooting Symptom Checks RemedyPage Limited Warranty Plasma Monitors This warranty may be enforced only by the first purchaserFor More Information Telephone 408 735 Faroudja Palomar Ave Sunnyvale, CA
Top Page Image Contents