Meridian Audio FPP-61HD20 Important Information, Precautions, Risk of Electric Shock Do not Open

Page 2

Important Information

Precautions

Please read this manual carefully before using your plasma monitor and keep the manual handy for future reference.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER. NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

This symbol warns the user that uninsulated voltage within the unit may have sufficient magnitude to cause electric shock. Therefore, it is dangerous to make any kind of contact with any part inside of this unit.

This symbol alerts the user that important literature concerning the operation and maintenance of this unit has been included. Therefore, it should be read carefully in order to avoid any problems.

WARNING

TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. ALSO DO NOT USE THIS UNIT’S POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLETS, UNLESS THE PRONGS CAN BE FULLY INSERTED. REFRAIN FROM OPENING THE CABINET AS THERE ARE HIGH-VOLTAGE COMPONENTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

Warnings and Safety Precaution

This plasma monitor is designed and manufactured to provide long, trouble-free service. No maintenance other than cleaning is required. Please see the section “Plasma monitor cleaning procedure” on the next page.

The plasma display panel consists of fine picture elements (cells) with more than 99.99 percent active cells. There may be some cells that do not produce light or remain lit.

For operating safety and to avoid damage to the unit, read carefully and observe the following instructions. To avoid shock and fire hazards:

1.Provide adequate space for ventilation to avoid internal heat build-up. Do not cover rear vents or install the unit in a closed cabinet or shelves.

If you install the unit in an enclosure, make sure there is adequate space at the top of the unit to allow hot air to rise and escape. If the monitor becomes too hot, the overheat protector will be activated and the monitor will be turned off. If this happens, turn off the power to the monitor and unplug the power cord. If the room where the monitor is installed is particularly hot, move the monitor to a cooler location, and wait for 60 minutes to cool the monitor. If the problem persists, contact your dealer for service.

2.Do not use this unit’s polarized plug with extension cords or outlets unless the prongs can be completely inserted.

3.Do not expose the unit to water or moisture.

4.Avoid damage to the power cord, and do not attempt to modify the power cord.

5.Unplug the power cord during electrical storms or if the unit will not be used over a long period.

6.Do not open the cabinet which has potentially dangerous high voltage components inside. If the unit is damaged in this way the warranty will be void. Moreover, there is a serious risk of electric shock.

7.Do not attempt to service or repair the unit. The manufacturer is not liable for any bodily harm or damage caused if unqualified persons attempt service or open the back cover. Refer all service to authorized Service Centers.

Page 1 Page 3
Image 2
Page 1 Page 3
Contents Digital Cinema Series Risk of Electric Shock Do not Open PrecautionsImportant Information To avoid damage and prolong operating life Use only with120V50/60HzAC powerPlasma monitor cleaning procedure Recommendations to avoid or minimize phosphor burn-inMises en garde et précautions de sécurité Recommandations importantesPrécautions Méthode de nettoyage du moniteur à plasma Contents How to Attach Options to the Plasma Monitor Ventilation Requirements for enclosure mountingPart Names and Function Turns the monitor’s power on and offReceives the signals from the remote control Front ViewRear View/ Terminal Board RGB2Remote Control Not functional for the models covered in this manual Battery Installation and ReplacementTransmits the remote control signals Clears the number set by the ID Select buttonOperating Range Using the wired remote control modeHandling the remote control Installation Connections Pin Assignments and Signal Levels for 15 pin RGB Analog Signal AnalogBasic Operations After the power is turned off with the off timer To set the off timerTo cancel the off timer To check the remaining timeWhen viewing videos or digital video discs Wide Operations Supported resolution Wide Screen Operation with Computer SignalsWhen Picture Size is set to OFF  Picture Size setting Advanced menu mode Menu OperationsReset Menu TreeOPTION2 PWR. MGT  Picture adjustment screen Picture Settings MenuAdjusting the picture  Adjusting for the video processorReducing noise in the picture Setting the color temperatureAdjusting the color to the desired level  Gamma settings Making the Low Tone adjustments Adjusting the white balance  LOW Tone settings Color Tune settings Audio Settings MenuAdjusting the colors  Audio settings menuAdjusting the Position, Size, Fine Picture, Picture Adj Image Adjust Settings MenuSetting the allocation of the audio connectors Example Setting Audio INPUT1 to VideoOption1 Settings Menu Setting the on-screen menuSetting a computer image to the correct RGB select screen Setting the BNC connectorsChecking the signal being transmitted to RGB1 terminal  OSM Orbiter settings Input Skip settings Setting high definition images to the suitable screen sizeSetting the Input Skip  RGB Select modesSetting the power management for computer images Option2 Settings MenuResetting to the default values  PLE settings POWER/STANDBY indicatorSetting the picture to suit the movie Reducing burn-in of the screen Inverse Settings  Orbiter settings Orbiter Function settings Screen Wiper  Setting the time To select on for the Working Time  Gray Level settings Setting the screen size for S1/S2 video input Soft Focus settings Speed S1/S2 settings Setting the picture size for RGB input signalsSetting the signal and black level for DVI signal  PLUG/PLAY settings Present Time settings Option3 Settings MenuUsing the timer Present Time To reset the data Setting the power on mode To reset the program  Special characters in the Program Timer screen Control Lock settings Enabling/disabling remote control wireless transmission PWR. on Mode settings  IR Remote settingsLoop Out setting ID number setting Video Wall Position settings Video Wall setting Divider settings Divider Image Adjust settings  Auto ID settings DISP. Mode settings  PLE Link settings On Delay Power on delay P. on Delay settings PLE LinkRepeat Timer Advanced OSM Settings MenuSetting the menu mode  Repeat Timer settingsSetting the language for the menus Language Settings MenuColor System Settings Menu Setting the video signal formatConnections External ControlApplication Communication ParametersTroubleshooting Symptom Checks RemedyPage For More Information Limited Warranty Plasma MonitorsThis warranty may be enforced only by the first purchaser Telephone 408 735 Faroudja Palomar Ave Sunnyvale, CA
Top Page Image Contents