Exmark 4500-497 manual Safety Alert Symbol, Safe Operating Practices, Training, Preparation

Page 5

Safety

Safety

Safety Alert Symbol

This Safety Alert Symbol (Figure 2) is used both in this manual and on the machine to identify important safety messages which must be followed to avoid accidents

This symbol means: ATTENTION! BECOME

ALERT! YOUR SAFETY IS INVOLVED!

Figure 2

1.Safety alert symbol

The safety alert symbol appears above information which alerts you to unsafe actions or situations and will be followed by the word DANGER, WARNING, or CAUTION.

DANGER: White lettering / Red background. Indicates an imminently hazardous situation which, if not avoided, Will result in death or serious injury.

WARNING: Black lettering / Orange background. Indicates a potentially hazardous situation which, if not avoided, Could result in death or serious injury.

CAUTION: Black lettering / Yellow background. Indicates a potentially hazardous situation which, if not avoided, May result in minor or moderate injury.

This manual uses two other words to highlight information. Important calls attention to special mechanical information and Note emphasizes general information worthy of special attention.

Safe Operating Practices

Training

Read the Operator’s Manual and other training material. If the operator(s) or mechanic(s) can not read English it is the owner’s responsibility to explain this material to them.

Become familiar with the safe operation of the equipment, operator controls, and safety signs.

All operators and mechanics should be trained. The owner is responsible for training the users.

Never let children or untrained people operate or service the equipment. Local regulations may restrict the age of the operator.

The owner/user can prevent and is responsible for accidents or injuries occurring to himself or herself, other people or property.

Preparation

Evaluate the terrain to determine what accessories and attachments are needed to properly and safely perform the job. Only use accessories and attachments approved by Exmark.

Wear appropriate clothing including safety glasses, substantial footwear, long trousers, and hearing protection. Do Not operate when barefoot or when wearing open sandals. Long hair, loose clothing or jewelry may get tangled in moving parts.

CAUTION

This machine produces sound levels in excess of 85 dBA at the operator’s ear and can cause hearing loss through extended periods of exposure.

Wear hearing protection when operating this machine.

Inspect the area where the equipment is to be used and remove all rocks, toys, sticks, wires, bones, and other foreign objects which can be thrown by the machine and may cause personal injury to the operator or bystanders.

5

Image 5
Contents Frontrunnertm California Introduction Contents Safety Alert Symbol SafetySafe Operating Practices TrainingSafety Operation Slope Operation Using the Rollover Protection System RopsMaintenance and Storage Safety Safety and Instructional Decals 109-2355 109-2356 109-2358 109-2377 109-2396 109-7413 116-1003 109-2360 Systems SpecificationsModel Numbers Cutting Deck Hydrostatic Ground Drive SystemTires & Wheels Torque Requirements DimensionsControls Product OverviewOperation Pre-Start Raise the Rollover Protection System Rops Operating InstructionsOpen the Fuel Shut-Off Valve Starting the EngineStopping the Engine Driving the MachineDisengaging the PTO Transporting a Unit TransportingLoading a Unit Recommended Maintenance Schedules MaintenanceCheck Engine Oil Level Check Battery ChargeEngine must initiate shutdown Check Safety Interlock SystemService Air Cleaner Check Rollover Protections Systems Roll Bar PinsCheck Seat Belt Check for Loose HardwareCheck Tire Pressures Check Auxiliary Hydraulic Oil LevelCheck Condition Of Belts Lubricate Grease FittingsPumps Places Lubricate Rear Caster Wheel HubsLubricate Brake Handle Pivot Lubricate Motion Control ShaftLubricate Brake Rod Bushings Lubricate Motion Control Bronze BushingsChange Hydraulic System Filter Fuel Tank Mounting Hardware SpecificationsCheck Wheel Hub Locknuts Thread Locking AdhesivesPark Brake Adjustment Pump Drive Belt ReplacementDielectric Grease Pump Drive Belt TensionMotion Control Linkage Adjustment Weight Transfer Spring Adjustment Clutch Shim Caster Pivot Bearings Pre-Load AdjustmentFeeler gauge Brake mounting bolt Clean Engine Cooling System CleaningBattery Disposal Remove Engine Shrouds and Clean Cooling FinsWaste Disposal Motor Oil DisposalProblem Possible Cause Corrective Action TroubleshootingTroubleshooting Ignition Switch Schematics31HP Ignition SwitchBlack / Grey Rown B Electrical Logic Schematic 27HP KohlerViolet Electrical Logic Schematic 31HP Briggs & StrattonHydraulic Diagram Exmark Commercial Turf Equipment Page Page Service Record Page Page See EXMARK’S Complete Line of Accessories and Options