Exmark 4500-872 manual Open the Fuel Shut-Off Valve, Starting the Engine, Engaging the PTO

Page 23

Operation

2.Apply forward pressure to the upper hoop of the roll bar.

3.Pull the knob and rotate 90° to hold in the unlatched position to lower the roll bar.

4.To return to the operate position, raise the roll bar, and then rotate knobs 90° so that the tabs interlock partially. Apply forward pressure to the roll bar upper hoop and observe that the knobs return to the completely latched position.

Figure 12

1.Roll bar upper hoop

2.Knob in “latched” position

3.Pull knob to unlatch

4.Rotate 90° to hold unlatched

5.Knob in “unlatched” position

5.Make sure the knobs are fully engaged with the roll bar in the raised position. The upper hoop of the roll bar may need to be pushed forward or pulled rearward to get both knobs fully engaged (see Figure 13).

 

Figure 13

1. Engaged

2. Partially engaged — Do

 

Not operate with ROPS

 

in this condition.

 

 

Important: Always use the seat belt with the roll bar in the operate (raised) position. Ensure that the rear part of the seat is secured with the seat latch.

Open the Fuel Shut-Off Valve

Rotate the valve and align with the fuel line to open.

Starting the Engine

1.Move the motion control levers out to the neutral lock position.

2.Pull up and back on the parking brake lever to engage the parking brake.

3.Push down on the PTO switch to the “disengage” position.

Note: It is not necessary for the operator to be in the seat to start the engine.

4.Place the throttle midway between the “SLOW” and “FAST” positions.

5.On a cold engine, push the choke lever forward into the “ON” position.

On a warm engine, leave the choke in the “OFF” position.

6.Turn ignition switch to the “START” position. Release the switch as soon as the engine starts.

Important: Do Not crank the engine continuously for more than ten seconds at a time. If the engine does not start, allow a 60 second cool-down period between starting attempts. Failure to follow these guidelines can burn out the starter motor.

7.If the choke is in the “ON” position, gradually return choke to the “OFF” position as the engine warms up.

Engaging the PTO

DANGER

The rotating blades under the mower deck are dangerous. Blade contact can cause serious injury or kill you.

Do Not put hands or feet under the mower or mower deck when the blades are engaged.

23

Image 23
Contents Lazer Z E-SERIES California Introduction Contents Training SafetySafety Alert Symbol Safe Operating PracticesSafety Slope Operation OperationMaintenance and Storage Using the Rollover Protection System RopsSafety Safety Safety and Instructional Decals 109-7232 109-8483 116-2927 Systems SpecificationsModel Numbers Cutting Deck SeatHydrostatic Ground Drive System Tires & WheelsDimensions Torque Requirements Accessory Weight Table WorksheetMotion Control Levers Product OverviewOperation ControlsBrake Lever Ignition SwitchChoke Control Throttle ControlDrive Wheel Release Valves Fuel Shut-Off ValveFuel Gauge Operating Instructions Pre-StartEngaging the PTO Open the Fuel Shut-Off ValveStarting the Engine Driving the Machine Disengaging the PTOStopping the Engine Driving Forward Adjusting the Cutting HeightAdjusting the Anti-Scalp Rollers Adjusting the Deck Lift Foot Pedal 48 & 52 inch Decks OnlyTransporting a Unit TransportingLoading a Unit Recommended Maintenance Schedules MaintenanceCheck Engine Oil Level Check Battery ChargeService Interval As required Recommended Jump Starting ProcedureCheck Mower Blades Check Safety Interlock SystemCheck for Loose Hardware Service Air CleanerCheck Rollover Protections Systems Roll Bar Knobs Check Seat BeltCheck Condition Of Belts Check Hydraulic Oil LevelCheck Tire Pressures Lubricate Caster Wheel Hubs Lubricate Grease FittingsChange Fuel Filter Lubricate Brake Handle PivotLubricate Deck Lift Pivot Check Spark PlugsCheck Spark Arrester if equipped Wheel Hub Slotted Nut Torque SpecificationThread Locking Adhesives Copper-Based Anti-seizeDeck Leveling AdjustmentsDeck Belt Tension Adjusting the Parking BrakePump Drive Belt Tension Left Hand Brake Shown Start the mower while in the operator position Electric Clutch AdjustmentMotion Control Linkage Adjustment RH Motion Control Shown Motion Control Damper AdjustmentMotion Control Handle Adjustment Motion Control Neutral Lock Pivot AdjustmentClean Hydro Cooling Fins Caster Pivot Bearings Pre-Load AdjustmentClean Engine and Exhaust System Area Remove Engine Shrouds and Clean Cooling FinsWaste Disposal Clean Debris From MachineClean Grass Build-Up Under Deck Battery DisposalProblem Possible Cause Corrective Action TroubleshootingSee Drive Wheel Release Valves section Troubleshooting Electrical Diagram SchematicsElectrical SchematicHydraulic Diagram Lazer Z E-Series Turf Equipment Page This page may be copied for personal use See EXMARK’S Complete Line of Accessories and Options