Exmark 4500-872 manual See EXMARK’S Complete Line of Accessories and Options

Page 56

SEE EXMARK’S COMPLETE LINE OF ACCESSORIES AND OPTIONS

MID-MOUNT RIDING ACCESSORIES AND OPTIONS

CUSTOM RIDE SEAT SUSPENSION SYSTEM	OPERATOR CONTROLLED DISCHARGE
FULL SUSPENSION SEAT	ROLL OVER PROTECTION SYSTEM (ROPS)
DECK LIFT ASSIST KIT	SUN SHADE
HITCH KIT	TRASH CONTAINER
LIGHT KIT	TURF STRIPER
12V POWER PORT	ULTRA VAC COLLECTION SYSTEM
MICRO-MULCH SYSTEM	ULTRA VAC QUICK DISPOSAL SYSTEM
OUT-FRONT RIDING ACCESSORIES AND OPTIONS
CUSTOM RIDE SEAT SUSPENSION SYSTEM	SNOW BLADE
DUAL-TAIL WHEEL	SNOWBLOWER
FLOOR PAN EXTENDER	SUN SHADE
HITCH KIT	TRASH CONTAINER
LIGHT KIT	ULTRA VAC COLLECTION SYSTEM
MICRO-MULCH SYSTEM	ULTRA VAC QUICK DISPOSAL SYSTEM
ROLL OVER PROTECTION SYSTEM (ROPS)	WEATHER CAB

WALK-BEHIND ACCESSORIES AND OPTIONS

GRASS CATCHER

MICRO-MULCH SYSTEM

Place Model No. and Serial No.

Label Here (Included in the Literature

Pack) or Fill in Below

Model No.

Serial No.

TURF STRIPER

STANDON

Date Purchased

Engine Model No. and Spec. No.

Engine Serial No. (E/No)

©2010 Exmark Mfg. Co., Inc.	Part No. 4500-872 Rev. A
Industrial Park Box 808	(402) 223-6300
Beatrice, NE 68310	Fax (402) 223-5489
All Rights Reserved	Printed in the USA

www.exmark.com

Image 56

Contents Lazer Z E-SERIES California Introduction Contents Safety Safety Alert SymbolSafe Operating Practices TrainingSafety Operation Slope OperationUsing the Rollover Protection System Rops Maintenance and StorageSafety Safety Safety and Instructional Decals 109-7232 109-8483 116-2927 Systems SpecificationsModel Numbers Seat Hydrostatic Ground Drive SystemTires & Wheels Cutting DeckDimensions Accessory Weight Table Worksheet Torque RequirementsProduct Overview OperationControls Motion Control LeversIgnition Switch Choke ControlThrottle Control Brake LeverDrive Wheel Release Valves Fuel Shut-Off ValveFuel Gauge Pre-Start Operating InstructionsEngaging the PTO Open the Fuel Shut-Off ValveStarting the Engine Driving the Machine Disengaging the PTOStopping the Engine Adjusting the Cutting Height Driving ForwardAdjusting the Deck Lift Foot Pedal 48 & 52 inch Decks Only Adjusting the Anti-Scalp RollersTransporting Transporting a UnitLoading a Unit Maintenance Recommended Maintenance SchedulesCheck Battery Charge Check Engine Oil LevelRecommended Jump Starting Procedure Service Interval As requiredCheck Safety Interlock System Check Mower BladesService Air Cleaner Check Rollover Protections Systems Roll Bar KnobsCheck Seat Belt Check for Loose HardwareCheck Condition Of Belts Check Hydraulic Oil LevelCheck Tire Pressures Lubricate Grease Fittings Lubricate Caster Wheel HubsLubricate Brake Handle Pivot Lubricate Deck Lift PivotCheck Spark Plugs Change Fuel FilterWheel Hub Slotted Nut Torque Specification Thread Locking AdhesivesCopper-Based Anti-seize Check Spark Arrester if equippedAdjustments Deck LevelingDeck Belt Tension Adjusting the Parking BrakePump Drive Belt Tension Left Hand Brake Shown Electric Clutch Adjustment Start the mower while in the operator positionMotion Control Linkage Adjustment Motion Control Damper Adjustment RH Motion Control ShownMotion Control Neutral Lock Pivot Adjustment Motion Control Handle AdjustmentCaster Pivot Bearings Pre-Load Adjustment Clean Engine and Exhaust System AreaRemove Engine Shrouds and Clean Cooling Fins Clean Hydro Cooling FinsClean Debris From Machine Clean Grass Build-Up Under DeckBattery Disposal Waste DisposalTroubleshooting Problem Possible Cause Corrective ActionSee Drive Wheel Release Valves section Troubleshooting Schematics Electrical DiagramSchematic ElectricalHydraulic Diagram Lazer Z E-Series Turf Equipment Page This page may be copied for personal use See EXMARK’S Complete Line of Accessories and Options