Exmark 4500-872 manual Clean Debris From Machine, Clean Grass Build-Up Under Deck, Waste Disposal

Page 46

Maintenance

2.Slide seat all the way forward.

3.Remove accumulated debris from the hydro cooling fins.

Clean Debris From Machine

Service Interval: Before each use or daily

1.Stop engine, wait for all moving parts to stop, and remove key. Engage parking brake.

2.Clean off any oil, debris, or grass build-up on the machine and cutting deck, especially under deck belt shields, around the fuel tank, around engine and exhaust area.

Clean Grass Build-Up Under Deck

Service Interval: Before each use or daily

1.Stop engine, wait for all moving parts to stop, and remove key. Engage parking brake.

2.Raise deck to the transport (4 1/2 inch (11.4 cm) cutting height) position. Lift the front of unit and support unit using jack stands or equivalent support.

CAUTION

Raising the mower deck for service or maintenance relying solely on mechanical or hydraulic jacks could be dangerous. The mechanical or hydraulic jacks may not be enough support or may malfunction allowing the unit to fall, which could cause injury.

Do Not rely solely on mechanical or hydraulic jacks for support. Use adequate jack stands or equivalent support.

3.Clean out any grass build-up from underside of deck and in discharge deflector.

Waste Disposal

Motor Oil Disposal

Engine oil and hydraulic oil are both pollutants to the environment. Dispose of used oil at a certified recycling center or according to your state and local regulations.

Battery Disposal

DANGER

Battery electrolyte contains sulfuric acid, which is poisonous and can cause severe burns. Swallowing electrolyte can be fatal or if it touches skin can cause severe burns.

Wear safety glasses to shield eyes, and rubber gloves to protect skin and clothing when handling electrolyte.

Do Not swallow electrolyte.

In the event of an accident, flush with water and call a doctor immediately.

Federal law states that batteries should not be placed in the garbage. Management and disposal practices must be within relevant federal, state, or local laws.

If a battery is being replaced or if the unit containing the battery is no longer operating and is being scrapped, take the battery to a local certified recycling center. If no local recycling is available return the battery to any certified battery reseller.

46

Image 46
Contents Lazer Z E-SERIES California Introduction Contents Safe Operating Practices SafetySafety Alert Symbol TrainingSafety Operation Slope OperationUsing the Rollover Protection System Rops Maintenance and StorageSafety Safety Safety and Instructional Decals 109-7232 109-8483 116-2927 Model Numbers SpecificationsSystems Tires & Wheels SeatHydrostatic Ground Drive System Cutting DeckDimensions Accessory Weight Table Worksheet Torque RequirementsControls Product OverviewOperation Motion Control LeversThrottle Control Ignition SwitchChoke Control Brake LeverFuel Gauge Fuel Shut-Off ValveDrive Wheel Release Valves Pre-Start Operating InstructionsStarting the Engine Open the Fuel Shut-Off ValveEngaging the PTO Stopping the Engine Disengaging the PTODriving the Machine Adjusting the Cutting Height Driving ForwardAdjusting the Deck Lift Foot Pedal 48 & 52 inch Decks Only Adjusting the Anti-Scalp RollersTransporting Transporting a UnitLoading a Unit Maintenance Recommended Maintenance SchedulesCheck Battery Charge Check Engine Oil LevelRecommended Jump Starting Procedure Service Interval As requiredCheck Safety Interlock System Check Mower BladesCheck Seat Belt Service Air CleanerCheck Rollover Protections Systems Roll Bar Knobs Check for Loose HardwareCheck Tire Pressures Check Hydraulic Oil LevelCheck Condition Of Belts Lubricate Grease Fittings Lubricate Caster Wheel HubsCheck Spark Plugs Lubricate Brake Handle PivotLubricate Deck Lift Pivot Change Fuel FilterCopper-Based Anti-seize Wheel Hub Slotted Nut Torque SpecificationThread Locking Adhesives Check Spark Arrester if equippedAdjustments Deck LevelingPump Drive Belt Tension Adjusting the Parking BrakeDeck Belt Tension Left Hand Brake Shown Electric Clutch Adjustment Start the mower while in the operator positionMotion Control Linkage Adjustment Motion Control Damper Adjustment RH Motion Control ShownMotion Control Neutral Lock Pivot Adjustment Motion Control Handle AdjustmentRemove Engine Shrouds and Clean Cooling Fins Caster Pivot Bearings Pre-Load AdjustmentClean Engine and Exhaust System Area Clean Hydro Cooling FinsBattery Disposal Clean Debris From MachineClean Grass Build-Up Under Deck Waste DisposalTroubleshooting Problem Possible Cause Corrective ActionSee Drive Wheel Release Valves section Troubleshooting Schematics Electrical DiagramSchematic ElectricalHydraulic Diagram Lazer Z E-Series Turf Equipment Page This page may be copied for personal use See EXMARK’S Complete Line of Accessories and Options