Exmark 4500-872 manual Motion Control Damper Adjustment, RH Motion Control Shown

Page 43

Maintenance

WARNING

Engine must be running and drive wheels must be turning so adjustments can be performed. Contact with moving parts or hot surfaces may cause personal injury.

Keep fingers, hands, and clothing clear of rotating components and hot surfaces.

1.Prior to starting the engine, push the deck lift pedal and remove the height of cut pin. Lower deck to the ground.

2.Raise the rear of machine up and support with jack stands (or equivalent support) just high enough to allow drive wheels to turn freely.

3.Remove the electrical connection from the seat safety switch, located under the bottom cushion of the seat. The switch is a part of the seat assembly.

4.Temporarily install a jumper wire across the terminals in the connector of the main wiring harness.

5.Start engine. Brake must be engaged and motion control levers out to start engine. Operator does not have to be in the seat because of the jumper wire being used. Run engine at full throttle and release brake.

6.Run the unit at least 5 minutes with the drive levers at full forward speed to bring hydraulic oil up to operating temperature.

Note: The motion control lever needs to be in neutral while making any necessary adjustments.

7.Bring the motion control levers into the neutral position. Adjust pump control rod lengths by rotating the double nuts on the rod in the appropriate direction until the wheels slightly creep in reverse (Figure 35). Move the motion control levers to the reverse position and while applying slight pressure to the lever allow the reverse indicator springs to bring the levers back to neutral. The wheels must stop turning or slightly creep in reverse.

Figure 35

1.Double nuts

8.Shut off unit. Remove jumper wire from wire harness and plug connector into seat switch.

9.Remove the jack stands.

10.Raise the deck and re-install the height of cut pin.

11.Check that the machine does not creep in neutral with the park brakes disengaged.

Motion Control Damper Adjustment

The top damper mounting bolt can be adjusted to obtain a more desired motion control lever resistance. See Figure 36 for mounting options.

Figure 36

RH Motion Control Shown

1.Torque nyloc nut to 200 in-lb (16.7 ft-lb). Bolt must protrude past end of nyloc nut after torque. A T-40 Torx bit will be necessary to hold the stud from turning.

2.Most resistance (firmest feel)

3.Damper

4.Medium resistance (medium feel)

5.Least resistance (softest feel)

43

Page 42 Page 44
Image 43
Page 42 Page 44
Contents Lazer Z E-SERIES California Introduction Contents Training SafetySafety Alert Symbol Safe Operating PracticesSafety Slope Operation OperationMaintenance and Storage Using the Rollover Protection System RopsSafety Safety Safety and Instructional Decals 109-7232 109-8483 116-2927 Model Numbers SpecificationsSystems Cutting Deck SeatHydrostatic Ground Drive System Tires & WheelsDimensions Torque Requirements Accessory Weight Table WorksheetMotion Control Levers Product OverviewOperation ControlsBrake Lever Ignition SwitchChoke Control Throttle ControlFuel Gauge Fuel Shut-Off ValveDrive Wheel Release Valves Operating Instructions Pre-StartStarting the Engine Open the Fuel Shut-Off ValveEngaging the PTO Stopping the Engine Disengaging the PTODriving the Machine Driving Forward Adjusting the Cutting HeightAdjusting the Anti-Scalp Rollers Adjusting the Deck Lift Foot Pedal 48 & 52 inch Decks OnlyTransporting a Unit TransportingLoading a Unit Recommended Maintenance Schedules MaintenanceCheck Engine Oil Level Check Battery ChargeService Interval As required Recommended Jump Starting ProcedureCheck Mower Blades Check Safety Interlock SystemCheck for Loose Hardware Service Air CleanerCheck Rollover Protections Systems Roll Bar Knobs Check Seat BeltCheck Tire Pressures Check Hydraulic Oil LevelCheck Condition Of Belts Lubricate Caster Wheel Hubs Lubricate Grease FittingsChange Fuel Filter Lubricate Brake Handle PivotLubricate Deck Lift Pivot Check Spark PlugsCheck Spark Arrester if equipped Wheel Hub Slotted Nut Torque SpecificationThread Locking Adhesives Copper-Based Anti-seizeDeck Leveling AdjustmentsPump Drive Belt Tension Adjusting the Parking BrakeDeck Belt Tension Left Hand Brake Shown Start the mower while in the operator position Electric Clutch AdjustmentMotion Control Linkage Adjustment RH Motion Control Shown Motion Control Damper AdjustmentMotion Control Handle Adjustment Motion Control Neutral Lock Pivot AdjustmentClean Hydro Cooling Fins Caster Pivot Bearings Pre-Load AdjustmentClean Engine and Exhaust System Area Remove Engine Shrouds and Clean Cooling FinsWaste Disposal Clean Debris From MachineClean Grass Build-Up Under Deck Battery DisposalProblem Possible Cause Corrective Action TroubleshootingSee Drive Wheel Release Valves section Troubleshooting Electrical Diagram SchematicsElectrical SchematicHydraulic Diagram Lazer Z E-Series Turf Equipment Page This page may be copied for personal use See EXMARK’S Complete Line of Accessories and Options
Top Page Image Contents